Courtyard Creations RUS422F-WM User manual

ASSEMBLY INSTRUCTIONS
ATTENTION: THIS PRODUCT IS NOT FOR COMMERCIAL USE
INTENDED FOR RESIDENTIAL USE ONLY.
RUS422F-WM
PAGE 1 OF 6 COURTYARD CREATIONS INC.
STOP DON’T RETURN TO STORE!
Use the correct bolts as indicated. Do not tighten any of the bolts until is completely assembled.
Do not discard of any of the packaging until you have checked that you have all of the parts and
fittings required.
Keep children away during assembly. This item contains small parts that can be swallowed by
children. Children should always be under direct adult supervision while using this product.
Retain these assembly instructions for future reference.
Quote the following FQC NO. when contacting the service center.
!
!
!
!
!
SERVICE CENTER TOLL FREE NO.
TEL: [phone]
FAX: [phone]

PAGE 2 OF 6
STOP DON’T RETURN TO STORE!
A. Read instructions thoroughly. Acquaint yourself with the inventory of parts
and the accompanying drawings to ensure safe and proper assembly.
B. You will need the following tools:
- Phillips Screwdriver (Not Included)
- Nut Wrench (See Part #27)
- Hex. Key Wrench (See Part #26)
C. Lay out all parts on a flat surface and identify them using the table below.
PARTS LIST
PART
NO. MATERIAL CODE PART Q’TY PART NO. MATERIAL CODE PART Q’TY
1
2
3
4
5
6
7
8
9
10
12
13
11
1
2
2
2
1
2
1
4
2
2
2
4
6
14
15
16
17
18
19
21
20
22
23
24
25
26
27
282
2
2
2
2
2
2
4
24
16
2
8
1
1
1
RUS422F-CS01
62RUS422FN101
62RUS422FN102
62RUS422FQ101
62RUS422FM101
28000221042
28000221027
17GA06081101
17C01A0719072Y4
17C01A0706002Y4
62RUS422FH103
RUS422F-CS02
RUS422F-CS03
17C01A0721091Y4
17C01A0716072Y4
17C01A0714003Y4
17C02A0712003Y4
17C17A1306001Y4
17FA05050401-Y4
17KAA0201----Y4
RUS422F-CS05
RUS422F-CS04
REAR UPRIGHT SUPPORT
FRONT UPRIGHT SUPPORT
LATERAL CROSS BRACE
REAR CROSS BRACE
SWING ARM
SEAT
ASSEMBLY
SWING ARM TUBE
SUSPENSION SPRING
BOLT M6*55
BOLT M6*16
BOLT M6*60
BOLT M6*45
BOLT M6*40
BOLT M6*35
WASHER d6.5*D16*1.2
STEEL WASHER
HEX.KEY WRENCH 6MM
NUT WRENCH 10&13MM
TOP CROSS BEAM
W/ADJUSTABLE TEETH
FRONT LEG CAP
REAR LEG CAP
17KAB1101----Y4
18000626020
18000C23001
CANOPY
PLASTIC SCREW
CANOPY/FRAME CONNECTOR
PLASTIC NUT M6*P1.0
SCREW ST4.2*16
18000337002
BOLT CAP M6
18000337006
BOLT CAP M6
17XA9103

STOP DON’T RETURN TO STORE!
PAGE 3 OF 6
Step A - 1
Step A - 2
Step A - 3
Step A - 4
Fig. A
ASSEMBLY (Note: For all nuts and bolts
fastening, always use a washer (#19 or #20)
between the tube and bolt or the tube and
nut.)
Step A - 1:
Insert into the top cross beam w/adjustable
teeth (#1) upright supports (#2 and #3),
fasten them by using bolts (#12), washers
(#19) and plastic nuts (#21). Keep the bolts
loose. Do the same procedure for both sides.
Step A - 2:
Fasten the lateral cross brace (#4) to the
upright supports (#2 and #3) by using bolts
(#13) and washers (#19). Do the same
procedure for both sides.
Step A - 3:
Fasten the rear cross brace (#5) to the rear
upright supports (#3) by using bolts (#14),
washers (#19) and plastic nuts (#21).
Tighten all of the plastic nuts and bolts.
13
13
22
22
19
19
14
21
22
19
19
Step A - 4:
Insert the front leg caps (#9) and rear leg
caps (#10) into all of the base feet.
9
9
10
10
2
2
3
3
3
5
4
4
3
2
2
3
3
1
1
Do not tighten the bolts
after Step A - 1. Fasten
all bolts after Fig A.
22
19 12
12
19
21
21 19 22
19

PAGE 4 OF 6
STOP DON’T RETURN TO STORE!
Fig. B
Fig. C
Fig. D
Step C:
Hook the suspension springs (#11) into the
top of both swing arm tubes (#8). Do the
same procedure for both sides.
Step D:
Hang the other side of the suspension
springs (#11) into the hole located on the
angled brace on the top cross beam
w/adjustable teeth (#1). Do the same
procedure for both sides.
Warning:
Make sure that both ends of the suspension
springs (#11) go completely through the
holes in the angled braces on the top cross
beam w/adjustable teeth (#1) and the swing
arm tubes (#8).
Step B:
Insert the front of the seat assembly (#7)
into the swing arm (#6). Fasten them
together by using bolt (#17) and steel
washer (#20). Open the seat assembly (#7)
and fasten a swing arm tube (#8) and a
swing arm (#6) to the seat assembly (#7) by
using bolt (#15) and washers (#19), and
plastic nut (#21). Do the same procedure for
both sides. Fasten another swing arm tube
(#8) to the swing arm (#6) at the front bend
by using bolts (#16), washers (#19), and
plastic nut (#21). Do the same procedure for
both sides.
8888
11
11
11
20
17
23
11
7
1
11
11
19
19
19
15
16
22
22
21
1
11 11
8
6
6
88
7
8

PAGE 5 OF 6
STOP DON’T RETURN TO STORE!
Fig. F
Fig. G
Fig. E
Step 1 & Step 2:
Slide the canopy/frame connectors (#24)
into the canopy (#28). Fasten them together
by using screws (#18) in the pre-drilled
holes. Make sure that the teeth of the
canopy/frame connectors are facing toward
the inside of the frame. Step 1
Step 2
Step F:
Fasten the canopy/frame connectors (#24)
to the adjustable teeth on the top cross
beam w/adjustable teeth (#1) by using a
plastic screws (#25).
Step G:
To assure stability, double check that all of
the bolts have been completely tightened
and cover them with bolt caps (#22 and #23).
Warning:
To avoid danger of suffocation, always keep
plastic bags or small parts away from babies
and children.
25
24
25
24
28
28
28
24
18
18
1

PAGE 6 OF 6
STOP DON’T RETURN TO STORE!
Cleaning and Maintenance
• Wash frame parts and fabric with mild soap and water, rinse thoroughly. Dry frame completely and allow the
fabric to drip dry.
• Do not use bleach, acid, or other solvents on the fabric or frame parts.
• In order to prolong the life and beauty of your swing, we recommend that the swing be stored in a dry area
when not in use. (For example, overnight or on rainy days)
• Inspect and tighten all bolts and fasteners on a regular basis to ensure proper performance and safety of your
swing.
Special Warnings
1. The user of this swing should always inspect it before each use.
2. It is essential to place this swing on level ground and not less than 6 feet from any obstruction; such as
fences, garages, houses, overhanging branches,laundry lines, or electrical wires.
3. Check the tightness of all of the nuts and bolts on a regular basis.
4. Make sure that the suspension springs are properly secured before each use.
5. Always remove the canopy in heavy wind conditions; otherwise the canopy may tip over and cause damage
to its parts.
6. The manufacturer will not accept responsibility for unauthorized repairs or modifications to the swing or its
parts.
7. Oil all of the metal parts that move regularly.
8. Weight limit is 500 lbs.
The store where you made your purchase
does not stock parts for this item.
If you need parts,
whether they are missing or damaged,
STOP!
Missing A Part?
No Need To Go Back To
The Store
Call us between 9:00 AM and 4:30 PM
Eastern Time Monday through Friday
Call Toll Free:
TEL: [phone]
FAX: [phone]
READ THESE INSTRUCTIONS COMPLETELY BEFORE STARTING ASSEMBLY
SEPARATE AND IDENTIFY ALL PARTS, MAKING SURE THAT YOU
HAVE ALL OF THEPARTSLISTED.
IF YOU DO NOTLOCATE ALL OF THE PARTS LISTED, INSPECT THE
PACKING MATERIAL FOR SMALL PARTSTHAT MAYHAVEBECOME
SEPARATED DURING SHIPMENT.
IF YOU EXPERIENCEANY DIFFICULTY DURING ASSEMBLYOR IF ANY
PARTS ARE MISSING OR DAMAGED,CALL THE HELP LINE AT
1-877-539-7436 BEFORERETURNING THIS ITEM TO THE STORE.
PROVIDE THEFOLLOWING INFORMATION WHEN CALLING:
1-MODEL NUMBER OF THEPRODUCT.
2-PARTNUMBER AND MATERIAL CODE OF THE PARTFROM THE PARTS
LIST.
MOST PROBLEMS CAN BERESOLVED WITHOUT RETURNING THIS
PRODUCT TO THERETAILER.