Courtyard Creations KTS6463-WM User manual

ASSEMBLY INSTRUCTIONS
ATTENTION: THIS PRODUCT IS NOT FOR COMMERCIAL USE
INTENDED FOR RESIDENTIAL USE ONLY.
Attention:
Make sure that each bolt needed for all steps matches
the corresponding figure to ensure proper assembly.
Step 1:
Place the left leg (#3) onto a non-abrasive surface, such
as a carpet, with its underside facing upwards. Fasten
the supports (#2) to the left leg (#3) and the right leg
(#4) by using bolts (#5) and washers (#7). Keep the
bolts loose. See Figure 1.
PARTS LIST
PART
NO. MATERIAL CODE PART QTY PART NO. MATERIAL CODE PART QTY
1
2
3
4
5
16
7
8
9
10
4
16
12
4
1
HEX.KEY WRENCH 4MM
BOLT CAP M6
BOLT CAP
WASHER d6.5*D13*1.0
BOLT M6*35
3
1
1
12
BOLT M6*16
SEATASSEMBLY
LEFT LEG
RIGHT LEG
SUPPORT
62KTS6463Q101
KTS6463-CS04-4
KTS6463-CS02-1
KTS6463-CS04-3
17C33A0706001Y4
17C01A0712001Y4
17FA05040301-Y4
18000337004
18000337001
17KAA0101----Y4
KTS6463- WM
PAGE 1 OF 2
FIGURE 1
16
7
5
3
2
2
2
48
7
5
8
#5 BOLT M6*16
COURTYARD CREATIONS INC.
Use the correct bolts as indicated. Do not tighten any of the bolts until is completely assembled.
Do not discard of any of the packaging until you have checked that you have all of the parts and
fittings required.
Keep children away during assembly. This item contains small parts that can be swallowed by
children. Children should always be under direct adult supervision while using this product.
Retain these assembly instructions for future reference.
Quote the following FQC NO. when contacting the service center.
!
!
!
!
!
STOP DON’T RETURN TO STORE!
SERVICE CENTER TOLL FREE NO.
TEL: [phone]
FAX: [phone]
R
L
Note:
The labels marked “L” and “R” on legs (#3 and #4)
should coincide with Figure 1 to ensure proper assembly.

PAGE 2 OF 2
STOP DON’T RETURN TO STORE!
The store where you made your purchase
does not stock parts for this item.
If you need parts,
whether they are missing or damaged,
STOP!
MissingAPart?
No Need To Go Back To
The Store
Call us between 9:00 AM and 4:30 PM
Eastern Time Monday through Friday
Call Toll Free:
TEL: [phone]
FAX: [phone]
READ THESE INSTRUCTIONS COMPLETELY BEFORE STARTING ASSEMBLY
SEPARATE AND IDENTIFY ALL PARTS, MAKING SURE THAT YOU
HAVE ALL OF THEPARTSLISTED.
IF YOU DO NOTLOCATE ALL OF THE PARTS LISTED, INSPECT THE
PACKING MATERIAL FOR SMALL PARTSTHAT MAYHAVEBECOME
SEPARATED DURING SHIPMENT.
IF YOU EXPERIENCEANYDIFFICULTY DURING ASSEMBLYOR IF ANY
PARTS ARE MISSING OR DAMAGED,CALL THE HELP LINE AT
1-877-539-7436 BEFORERETURNING THIS ITEM TO THE STORE.
PROVIDE THEFOLLOWING INFORMATION WHEN CALLING:
1-MODEL NUMBER OF THEPRODUCT.
2-PARTNUMBER AND MATERIAL CODE OF THE PARTFROM THE PARTS
LIST.
MOST PROBLEMSCAN BERESOLVED WITHOUT RETURNING THIS
PRODUCT TO THERETAILER.
Step 2:
Place the seat assembly (#1) onto a non-abrasive
surface, such as a carpet, with its underside facing
upwards. Fasten the leg assembly to the seat assembly
(#1) by using bolts (#6) and washers (#7). Make sure
that all of the bolts have been tightened completely
and cover them with bolts caps (#8 and #9).
See Figure 2.
Step 3:
Turn the chair to its upright position. See Figure 3.
Cleaning and Maintenance
• Wash frame parts with mild soap and water, rinse thoroughly, and dry completely. Do not use bleach, acid, or
other solvents on the frame parts.
•We recommend the use of furniture covers when not in use.
•Inspect and tighten all bolts and fasteners on a regular basis to ensure the proper performance and safety of
your chair.
•In order to prolong the life and beauty of your chair, we recommend that it be stored in a dry and protected
area during off season periods.
FIGURE 2
69
3
4
1
7
FIGURE 3
35 #6 BOLT M6*35