Courtyard Creations RLS409A-WM User manual

ASSEMBLY INSTRUCTIONS
ATTENTION: THIS PRODUCT IS NOT FOR COMMERCIAL USE
INTENDED FOR RESIDENTIAL USE ONLY.
PAGE 1 OF 6
RLS409A-WM
COURTYARD CREATIONS INC.
Do not discard of any of the packaging until you have checked that you have all of the parts and
fittings required.
Keep children away during assembly. This item contains small parts that can be swallowed by
children. Children should always be under direct adult supervision while using this product.
Retain these assembly instructions for future reference.
Quote the following FQC NO. when contacting the service center.
!
!
!
!
SERVICE CENTER TOLL FREE NO.
TEL: [phone]
FAX: [phone]
STOP DON’T RETURN TO STORE!

A. Read these instructions thoroughly and acquaint yourself with the parts and
the illustrations to ensure safe and proper assembly.
B. You will need the following tools
- Phillips Screwdriver
- Nut Wrench (See Part #29)
- Hex. Key Wrench (See Part #28)
C. Lay out all of the parts and match them with the table below.
PAGE 2 OF 6
PARTS LIST
PART
NO.
1
2
3
5
6
7
8
9
10
11
12
13
14
15
116
17
18
19
20
21
22
23
24
25
26
27
28
29
30
1
1
1
2
2
16
4
8
4
6
2
2
4
6
22
1
1
2
2
2
2
2
2
4
4
1
1
6
RLS409A-CS01 17C01A0716072Y4
17C01A0712002Y4
17C01A0710002Y4
17C17A1306001Y4
17C01A0821061Y4
17C01A0706002Y4
17FA08060601-Y4
17FA05050401-Y4
18000C06001
18000C23001
18000337005
18000337002
18000615004
18000018001
17KAA0201----Y4
17KAB1201----Y4
61R409AD00001BA
WASHER d6.5*D16*1.2
BOLT M6*45
BOLT M6*35
BOLT M6*30
SCREW ST4.2*16
BOLT M8*60
BOLT M6*16
CANOPY/FRAME CONNECTOR
PLASTIC SCREW
HEX.KEY WRENCH 6MM
NUT WRENCH 13&17MM
CANOPY
62RLS409AH102
27LA08098
4 1
27LA08097
RLS409A-CS02
RLS409A-CS03
RLS409A-CS04
RLS409A-CS05
RLS409A-CS06
62RLS409AM101
62RLS409AI101
62RLS409AH201
17GA06081101
TOP CROSS BEAM W/ADJUSTABLE TEETH
REAR CROSS BRACE
RIGHT LATERAL CROSS BRACE
LEFT LATERAL CROSS BRACE
FRONT UPRIGHT SUPPORT
REAR UPRIGHT SUPPORT
SWING ARM
SEAT ASSEMBLY
BACK ASSEMBLY
SWING ARM TUBE
FRONT/REAR CANOPY BRACE
SIDE CANOPY BRACE
SUSPENSION SPRING
PLASTIC NUT M6*P1.0
PLASTIC NUT M8*P1.25
WASHER d8.5*D17*1.6
MATERIAL
CODE PART Q’TY PART NO. MATERIAL CODE PART Q’TY
BOLT CAP M8
BOLT CAP M6
STOP DON’T RETURN TO STORE!

PAGE 3 OF 6
Fig. A
Fig. B
Note:
When fastening with bolts and nuts, always use
a washer (#20 and #21) between the tube and
the bolt and the tube and the nut. Step A - 1
Step A - 2
Step A - 4
Do not tighten the bolts
after Step 1. Fasten all
bolts after Fig A.
Step A - 1 :
Fasten the front and rear upright supports (#5
and #6) at the top by using bolts (#14), washers
(#20), and plastic nuts (#22). Do the same
procedure for both sides. Keep the bolts loose.
Step A - 2 :
At both ends, insert the assembled upright
supports (#5 and #6) into the top cross beam
w/adjustable teeth (#1). Tighten all of the plastic
nuts and bolts.
Step A - 3 :
Fasten the lateral cross braces (#3 and #4) to the
upright supports (#5 and #6) by using bolts (#15)
and washers (#21). Do the same procedure for
both sides.
Step A - 4 :
Fasten the rear cross brace (#2) to the rear
upright supports (#6) by using bolts (#16),
washers (#21), and plastic nuts (#23). Tighten all
of the plastic nuts and bolts.
Step B :
Fasten the back assembly (#9) to the seat
assembly (#8) by using bolts (#17), washers
(#21), and plastic nuts (#23). Tighten all of the
plastic nuts and bolts.
24
24
14
14
20
20 20
22
22
20
Step A - 3
STOP DON’T RETURN TO STORE!
1
56
5
55
5
6
6
6
9
8
26
6
3
4
6
15
15 25
25
21
21
16
23
25
21 21
17
23
25
21 21
Note:
1. Do not fasten the lower rear holes of them yet.
2. To ensure proper assembly, the label marked
“L” and “R” on the lateral cross brace (#3 and
#4) should coincide with the label marked “L”
and “R” on the front upright supports (#5).
R
L
L
R

PAGE 4 OF 6
Fig. C
Fig. D
Fig. E
Step D :
Hook the suspension spring (#13) into the top of both
swing arm tubes (#10). Do the same procedure for
both sides.
Step E :
Hang the other side of the suspension spring (#13)
into the hole located on the angled brace on the top
cross beam w/adjustable teeth (#1). Do the same
procedure for both sides.
Warning :
Make sure that both ends of the suspension springs
(#13) go completely through the holes in the angled
braces on the top cross beam w/adjustable teeth (#1)
and the swing arm tubes (#10).
STOP DON’T RETURN TO STORE!
1
10 10 10
10
79
8
7
10 10 10 10
13
13
13 13
13
13
13
13
Step C :
Open the seat and back assembly and fasten a
swing arm tube (#10) and a swing arm (#7) to the
back assembly (#9) by using bolt (#17) and washers
(#21). Do the same procedure for both sides. Fasten
another swing arm tube (#10) to the swing arm (#7)
at the front bend by using bolt (#17), washers (#21),
and plastic nut (#23). Do the same procedure for
both sides. Fasten the other end of the swing arm
(#7) to the seat assembly (#8) by using bolt (#18)
and washers (#21). Do the same procedure for both
sides. 17
18 25
17
23
25
25
21 21
21
21

PAGE 5 OF 6
Fig. G
Step G :
Fasten the canopy/frame connectors (#26) on
the canopy assembly to the adjustable teeth
on both sides of the top cross beam (#1) by
using plastic screws (#27).
Fig. F
Step 1
Step 3
Step 2
Step 4
Step 5
STOP DON’T RETURN TO STORE!
12
12
12
12
11
11
11
1
11
30
30
30
30
27 26
26
19
19
Step F - 1 and Step F - 2 :
Slide the canopy/frame connectors (#26) onto
the side canopy braces (#11) and fasten into
position by using screws (#19). Make sure that
the teeth of the canopy connectors are facing
towards the inside of the swing.
Step F - 3 :
Insert the front and rear canopy braces (#12)
into the sleeves of the canopy (#30).
Step F - 4 :
Insert the tube ends of the side canopy braces
(#11) into the front and rear canopy braces
(#12).
Step F - 5 :
Insert the corners of the front and rear canopy
braces (#12) into the pockets of the canopy
(#30).
27
26

Fig. H
Cleaning and Maintenance
• Wash frame and fabric parts with mild
soap and water, rinse thoroughly, and dry
completely. Do not use bleach, acid, or
other solvents on the frame or fabric.
• The cushions and canopy may be surface washed with mild soap and water if necessary. Commercial foaming
upholstery cleaner may also be used. Rinse well and hang to dry. Do not machine wash or dry.
• We recommend the use of furniture covers to protect your swing when not in use.
• Inspect and tighten all bolts and fasteners on a regular basis to ensure proper performance and safety of your
swing.
• In order to prolong the life and beauty of your swing, we recommend that the cushions and fabric parts be
stored in a dry and protected area during off season periods (i.e. overnight or on rainy days)
Special Warnings
1. The user of this swing should always inspect it before each use.
2. It is essential to place this swing on level ground and not less than 6 feet from any obstruction; such as fences,
garages, houses, overhanging branches,laundry lines, or electrical wires.
3. Check the tightness of all of the nuts and bolts on a regular basis.
4. Make sure that the suspension springs are properly secured before each use.
5. Always remove the canopy in heavy wind conditions; otherwise the canopy may tip over and cause damage to
its parts.
6. The manufacturer will not accept responsibility for unauthorized repairs or modifications to the swing or its parts.
7. Oil all of the metal parts that move regularly.
8. Weight limit is 500 lbs.
The store where you made your purchase
does not stock parts for this item.
If you need parts,
whether they are missing or damaged,
STOP!
MissingAPart?
No Need To Go Back To
The Store
Call us between 9:00 AM and 4:30 PM
Eastern Time Monday through Friday
Call Toll Free:
TEL: [phone]
FAX: [phone]
READ THESE INSTRUCTIONS COMPLETELY BEFORE STARTING ASSEMBLY
SEPARATE AND IDENTIFY ALL PARTS, MAKING SURE THAT YOU
HAVE ALL OF THEPARTSLISTED.
IF YOU DO NOTLOCATE ALL OF THE PARTS LISTED, INSPECT THE
PACKING MATERIAL FOR SMALL PARTSTHAT MAYHAVEBECOME
SEPARATED DURING SHIPMENT.
IF YOU EXPERIENCEANY DIFFICULTYDURING ASSEMBLYOR IF ANY
PARTS ARE MISSING OR DAMAGED,CALL THE HELP LINE AT 1-877-539-7436
BEFORERETURNING THIS ITEM TO THESTORE.
PROVIDE THEFOLLOWING INFORMATION WHEN CALLING:
1-MODEL NUMBER OF THEPRODUCT.
2-PARTNUMBER AND MATERIAL CODE OF THE PARTFROM THE PARTS LIST
MOST PROBLEMSCAN BERESOLVED WITHOUT RETURNING THIS PRODUCT
TO THERETAILER.
STOP DON’T RETURN TO STORE!
PAGE 6 OF 6
Step H :
To assure stability, double check that all of
the bolts have been completely tightened
and cover them with bolt caps (#24 and #25).
Warning :
To avoid danger of suffocation, always keep
plastic bags or small parts away from babies
and children.