Coway Airmega 250 User manual
Feature HighlightsReal-time Air Quality Monitoring
P. 16Smart Mode
P. 15Rapid modeConnecting the Air Purifier to the Wi-Fi NetworkEZ release2
Max2 Filter
P. 5Filter Lifetime Notifications
P. 173
EN
Quick Start GuideDo not operate the product until completing these steps first.1 2
3
4
5 6
FRONT/전면/前
1
2
3
2
1
4
Connecting the Air Purifier to the Wi-Fi Network Checking the productPre-filterMax2 filter (Activated Carbon + Green True HEPA)Main UnitMax2 Filter*Pre-filter*5
EN
Table of Contents7Symbols Used in This Manual7Safety Instructions79Parts Diagram912Setting Up the Product12Connecting the Power and Turning On the Air Purifier13Connecting the Air Purifier to the Wi-Fi Network (250S Only)1314Smart Mode - Auto14Smart Mode - Sleep14Smart Mode - ECO15Rapid Mode15Setting the Timer15Checking the Air Quality16Adjusting the Sensor Sensitivity16Cover Open Notification Display17Reset The User-Selected Filter Replacement Cycle1718Filter Maintenance and Cleaning Parts18Check Wi-Fi Connection Aad Status2325Troubleshooting25Specification26Legal Notice27Limited Warranty296
Symbols Used in This ManualSafety InstructionsREAD AND SAVE THESE INSTRUCTIONS7
EN
01BEFORE USING THE PRODUCT
Safety InstructionsREAD AND SAVE THESE INSTRUCTIONS801BEFORE USING THE PRODUCT
Parts DiagramExteriorAir outlet coverControl panelAir quality indicatorFront coverHandles (left, right)Power cordSide ViewTop View9
EN
02PREPARATION
Parts Diagram1002PREPARATIONControl Panel (250S)8
1
2
4
6
7
3
5
Control Panel (250)8
1
2
4
6
7
3
5
11
EN
button/indicator1
Power button3
Speed button / indicator5
Filter reset button / indicator
2
Mode button / indicator4
Light button6
Wi-Fi button / indicator(Only 250S)7
Light sensor8
Air quality indicator
6
Timer button / indicator(Only 250)
123Open the cover located at the front ofthe product.Remove the plastic wrapping for Max2 filter.Return the filter and cover in reverse order at the first step. Place the Max2 filter into the filter case with the green side facing the product. Reversed placement may affect the filter lifetime.
FRONT/전면/前
2
1
1
2
12Setting Up the Product03INSTALLATION
12Insert the power plug into a power outlet.Touch the [Power] button to turn the air purifier on.Do not touch the control panel while connecting the power.Buttons may not work for a certain period of time.If the buttons do not work, unplug the power cord for about 10 minutes to discharge, and then connect it again.13
EN
Connecting the Power and Turning On the Air PurifierConnecting the Air Purifier to the Wi-Fi Network
Press the [Mode] button to select the smart mode.Press the [Mode] button to select the sleep mode. This mode minimizes thespeed during operation for a quiet and pleasant environment.Smart Mode - Sleep 1404OPERATIONSmart Mode - Auto Air QualityAir Speed
15
EN
Smart Mode - ECOSetting the TimerRapid ModeFor 250S users, you can set the timer and scheduler using Airmega application.Touch the [Timer] button until the indicator light displays the desired time.
Air quality indicatorThis indicator displays the indoor air quality in LED colors.
Good (blue) → Moderate (green) → Unhealthy (yellow) → Very unhealthy (Red)
23Press the [Mode] button to adjust it to the desired sensitivity.The mode indicator blinks as shown below once sensor sensitivity has been selected.Press the [Mode] button and the [Speed] button at the same time for more than about 2 seconds, the selected sensitivity will be inputted and the product will start operating normally.·
Air quality indicator1604OPERATIONChecking the Air QualityAdjusting the Sensor Sensitivity1While the product is operating, press the [Mode] button and the [Speed] button at the same time for more than 2 seconds.The speed indicator blinks to display the current sensor sensitivity level.·
When the front cover is detected open for more than 2 seconds, all indicators will turn off and the product stops all operation. When the front cover is detected closed for more than 1 second, the product returns to the previous operation mode.
2
The pre-filter indicator will start blinking. Then press the [Filter reset] button to select the filter that needs to be replaced or cleaned. Also, if you press the [Filter reset] button for more than 2 seconds, the selected filter option will reset.
· ·
1Press the [Filter reset] button and [Light] button at the same time for more than 2 seconds.
17
EN
Cover Open Notification DisplayReset The User-Selected Filter Replacement Cycle
Wipe the exterior of the product with a soft dry cloth.Exterior1805MAINTENANCEFilter Maintenance and Cleaning PartsMaintenance FilterMaintenance CycleCleaning PartsCleaning Cycle
1324Open the front cover by pulling out the top part of it. Remove dust with a vacuum cleaner or water depending on the degree of pollution.Pull the pre-filter upward to take it out.
Push in the dried pre-filter inside the product all the way to install. Close the side cover again.
1
2
2
1
19
EN
Pre-filterMax2 filter
20Front Covers05MAINTENANCE123Remove the front covers. · Remove dust with a soft, dry cloth or brush.Fit the cover to the grooves at the bottom of the product, and push the cover into place.
Other manuals for Airmega 250
3
This manual suits for next models
1
Table of contents
Languages:
Other Coway Air Cleaner manuals
Coway
Coway airmega 400S User manual
Coway
Coway airmega AP-1515G User manual
Coway
Coway AP-3008FH User manual
Coway
Coway AIRMEGA 230(W) User manual
Coway
Coway AP-1005AH User manual
Coway
Coway AP-1018F User manual
Coway
Coway Airmega 240 User manual
Coway
Coway Airmega 250 User manual
Coway
Coway Air Purifier AP-1008DH User manual
Coway
Coway AP-2505CH User manual
Coway
Coway AP-1012GH User manual
Coway
Coway airmega 400 User manual
Coway
Coway Airmega ProX User manual
Coway
Coway APM-1010DH User manual
Coway
Coway AP-2021A Gray User manual
Coway
Coway Airmega 200M User manual
Coway
Coway AP-1512HH User manual
Coway
Coway AP-0510IH User manual
Coway
Coway AP-1511FHE User manual
Coway
Coway AP-1009CH User manual
