Create WIND BALL User manual

WIND BALL
CEILING FAN WITH LIGHT
ASSEMBLY MANUAL

4
EN
To download this user guide in your language, visit our website:
www.create-store.com/uk
ES
Para descargar el manual en su idioma, visite nuestra web:
www.create-store.com/es
PT
Para baixar o manual no seu idiomas, visite nosso site:
www.create-store.com/pt
FR
Pour télécharger le manuel dans votre langue, visitez notre site Web:
www.create-store.com/fr
IT
Per scaricare il manuale nella sua lingua, visitare il nostro sito Web:
www.create-store.com/it
DE
Um das Handbuch in Ihrer Sprachen herunterzuladen, besuchen Sie unsere
Website:
www.create-store.com/de
NL
Bezoek onze website om de handleiding in uw taal te downloaden:
www.create-store.com/nl
PL
Aby pobrać instrukcję w swoim języku, odwiedź naszą stronę internetową:
www.create-store.com/pl
WIND BALL

5
WIND BALL
INDEX
Box contents 6
Step 1. Wood roof 7
Step 1. Concrete ceiling 8
Step 1. False ceiling 10
Choice of height 11
Step 2. Main body assembly 12
Step 3. Earth connection 14
Step 4. Driver connection 15
Step 5. Blade assembly 17
Step 6. Fitting the trim 18
Step 7. Led board connection 19
Step 8. Attaching the lamp cover 20
Blade balancing kit 21

6ENGLISH
A B
E
I J K L
F G H
C D
M N P
O Q
BOX CONTENTS
(1) EXPANSION SCREWS
FLOWER
EMBELLISHER
SPLICING TERMINALS BALANCING KIT
(x3) REVERSIBLE BLADES
SHANK EXTENSION BAR MOUNTING BRACKET EMBELLISHER
THE MOTOR
LAMP COVER
DRIVER
SUPPORT + ENGINE
REMOTE CONTROL LED PLATE
SCREWS FOR
TRIM + ENGINE
SCREWS OF
THE BLADES
(2) WOOD SCREWS
ATTENTION! Before starting the as-
sembly, remember to disconnect the
light from the electrical panel so as
not to suffer an electric shock.

7ENGLISH
K
STEP 1. WOOD CEILING
+ +
(2) WOOD SCREWS
OPTIONAL ACCORDING
TO CEILING TYPE
M
x4
1
3
5 6
4
If necessary, depending on the type of
ceiling, you will need to use a drill to make
the hole in the wood.
Repeat the previous step for the remaining
holes.
Place the washer and then the screw M2.Using the screwdriver, tighten the screw
M2.
Make sure that part K is perfectly xed to
the ceiling and that no wires are trapped.
Mark on the ceiling with a pencil the 4
holes of piece K.
K
PARTS AND TOOLS
M2
M2
NOT INCLUDED
2
K

8ENGLISH
STEP 1. CONCRETE CEILING
(1) EXPANSION SCREWS
With the help of a drill, make the two cor-
responding holes with an Ø8 mm drill bit.
Only the thread of the screw should stick
out.
Place the pieces M1 in the holes on the
ceiling.
Mark on the ceiling with a pencil the 2 cen-
tral holes of piece K, using the same piece
as a guide.
K
M1 M1
M1 M2 M3 M4
Disassemble part Mseparating it into pieces.
M
+ +
MK
PARTS AND TOOLS NOT INCLUDED
Ø8 mm
1
3
2
4

9ENGLISH
Place part Kmatching its holes with the
screws M1. Make sure the ceiling wires are
placed on one side of piece K.
M1 K
K
M4
5
7 8
6
Insert pieces M2, M3 and subsequently
the nut M4.
Tighten piece M4 with a # 10 wrench, until
you feel that it is well xed.
Make sure that piece K is perfectly hooked
to the ceiling and that no wires are trapped.
M2
M3
M4

10 ENGLISH
+ ++
PARTS AND TOOLS
STEP 1. FALSE CEILING
FIXING SCREWS
WITH SPRING LEVER
NOT INCLUDED
Make sure that part Kis perfectly attached to the ceiling to continue with the assembly.
With the help of a drill, make the two cor-
responding holes.
Insert the xing screws into the holes and
make sure the lever opens.
Place piece K and screw the xing screws
to the false ceiling.
Mark on the ceiling with a pencil the 2 cen-
tral holes using piece K as a guide.
K
K
X
1
3
5
4
2
K

11ENGLISH
I J
CHOICE OF HEIGHT
++
Using a screwdriver, remove the two screws on the bar tilt
bracket I.
Remove the pin from the tilt
bracket.
Carefully remove the pin
from the bar I.
Attach the tilt bracket to
the bar J.
Place the pin of the tilt sup-
port on the bar J.
Remove the tilt bracket
from the bar I.
Pull out the bar pin locking
piece I.
Slide the tilt stand down.
Before you start, choose the desired height.
(10cm+/-)
You will have to choose between the height of the
piece Iwave J.
· If you choose the height of the piece J, You must
follow the instructions below.
· If you choose the height of the piece I, go directly
to step 2 (page 12).
1
4
7 8 9
2
5
3
6
TILT SUPPORT
II
J J
J

12 ENGLISH
Snap the tilt bracket onto
the pin.
Tighten the two screws on
the tilt bracket with the
screwdriver.
Secure the pin with the
locking piece so that it does
not come out.
The piece J It would be
ready to use.
Put the pin back in the piece
J.
10
13 14
11 12
J
J
J
JI

13ENGLISH
STEP 2. MAIN BODY ASSEMBLY
++ /+ +
CHOOSE THE HEIGHT YOU NEED
A I JH L
Remove the pin from the
part Ieither J, depending on
the chosen height.
Enter the chosen bar through the hole in the part A.
1 2 3
A A
Insert the piece L As shown
in the picture.
With the help of a screw-
driver, remove the screws
from the top of the piece H.
Insert the bar at the top of
the part H.
Make sure no wires get
pinched.
Once the pieces are inserted Aand L, you must insert the
cables of the part H inside the bar. If you wish, you can tape
the wires to make them easier to handle.
4
7 8
5 6
9
H
H
L
H
H
H

14 ENGLISH
Once the bar has been in-
serted, place the pin of the
part I/Jso that it coincides
with the hole in the bar.
Put the locking piece on the
pin so that it does not come
out.
Then replace the screws on
the part Hso that the bar is
fully secured.
10 11 12
Once the bar is well anchored to the piece H, slide piece Ldown. The main body of the fan
motor will be assembled.
13 14
L
H

15ENGLISH
B
B
STEP 3. DRIVER CONNECTION
Put the tilt bracket into the
slot on the part K.
Remember to set the notch
on the tilt bracket back so
that the piece ts snugly.
Before continuing, check
that the central structure is
well placed so that it does
not fall.
K
1 2 3
+
B O
+
Join the part connections Bwith the motor connections,
each with its corresponding color.
4 5 6
Once the cables are con-
nected, insert the part Bin-
side the piece K, As shown
in the picture.

16 ENGLISH
Select and connect the
ground cables, including
the one for your installation.
You will need to attach the
remaining wires from the
piece Band the phase and
neutral cables of its instal-
lation in the strip of the
piece O, as it's shown in the
following.
Once connected, place the
pieces Oscrewing them
until they are secure.
7 8 9
O
Connect the LINE cable
of the driver (AC-L) to the
PHASE cable of your instal-
lation.
Connect the NEUTRAL ca-
ble of the driver (AC-N) to
the NEUTRAL cable of your
installation.
Make sure no wires are
pinched.
10 11 12
Slide piece A upwards to t it on the protruding screws of
the piece K.
Once tted, turn the piece A
to the right.
13 14 15
K
K
A

17ENGLISH
Finally, with the help of a screwdriver, tighten the screws so that the piece is well xed.
16 17 18
STEP 4. BLADE ASSEMBLY
++
E P
CHOOSE THE COLOR OF THE BLADE
Remember that the blades are reversible, choose the color you like best and put it facing
down. Then insert the blade Ein one of the slots of the piece Huntil it is positioned correctly.
1 2 3
HE
Once you have placed the blade E, screw it with 3 of the screws (part P). Repeat the step with
the remaining blades, making sure they are perfectly attached.
4 5 6
P
H
E
A

18 ENGLISH
STEP 5. FITTING THE TRIM
++
G N
Using a screwdriver, remove the 3 center screws from the
motor for later use. If these screws come separately in a
sealed bag, use them for this step.
Pass the motor cables
through the hole on the side
of the piece G.
Place the piece Galigning
its holes with the holes in
the motor.
Firmly tighten the screws so that the part Gis properly fas-
tened.
1
4
2
5
3
6
G
N

19ENGLISH
STEP 6. LED BOARD CONNECTION
D
Connect the part wires Dto those of the fan joining the connections,
each cable with its same color.
Then attach the part Dto the piece Gwith the help of the magnets so that it remains at-
tached.
1
3
2
4 5
D
D
D

20 ENGLISH
Place the piece F on the fan by snapping it onto the motor and secure it by turning clockwise.
Don't forget to check that the part Git is well attached. Once checked, you can connect the
electricity and enjoy your new fan with light.
1 2 3
STEP 7. ATTACHING THE LAMP COVER
F
F
Once checked, you can connect the electricity and enjoy your new fan with
light.