Crestron DigitalMedia 3 Series User manual

The Crestron® DMPS3-4K-350-C/DMPS3-4K-250-C Series consists of
the DMPS3-4K-350-C,DMPS3-4K-250-C,DMPS3-4K-350-C-AIRMEDIA,
and DMPS3-4K-250-C-AIRMEDIA. The devices provide 4K AV
presentation control and signal routing solutions for boardrooms and
classrooms. A built-in AirMedia® gateway enables wireless presentation
from computers and mobile devices. The DMPS3-4K-350-C and DMPS3-
4K-250-C require the purchase and activation of a license to enable
AirMedia gateway functionality. The DMPS3-4K-350-C-AIRMEDIA and
DMPS3-4K-250-C-AIRMEDIA provide AirMedia gateway functionality
without the need to purchase and activate a license.
In the Box
1 DMPS3-4K-350-C, DMPS3-4K-250-C, DMPS3-4K-350-C-
AIRMEDIA, or DMPS3-4K-250-C-AIRMEDIA 3-Series® 4K
DigitalMedia™ Presentation Systems
Additional Items
2 Bracket, Rack Ear, 3 RU (2033588)
3 Connector, 2-Pin (2012361)
1 Connector, 3-Pin (2003575)
4 Connector, 4-Pin (2003576)
15 Connector, 5-Pin (2003577)
2 Connector, 8-Pin (2003580)
4 Foot, 0.5 in. x 0.5 in. 0.23 in., Rubber (2002389)
1 Power Cord, 6 ft 7 in. (2 m) (2001134)
6 Screw, 6-32 x 5/16 in., Undercut Head, Phillips (2007223)
Install the Device
The Crestron DMPS3-4K-350-C, DMPS3-4K-250-C, DMPS3-4K-350-C-
AIRMEDIA, and DMPS3-4K-250-C-AIRMEDIA can be mounted into a rack
or placed onto a flat surface.
Mounting into a Rack
The DMPS3 devices each occupy 3 RU of rack space.
WARNING: To prevent bodily injury when mounting or servicing the
unit in a rack:
lWhen mounting the unit into a partially filled rack, load the rack
from the bottom to the top with the heaviest component at the
bottom of the rack.
lIf the rack is provided with stabilizing devices, install the stabilizers
before mounting or servicing the unit in the rack.
NOTE: Observe the following rack mount installation guidelines:
lElevated Operating Ambient Temperature: If installed in a closed or
multi-unit rack assembly, the operating ambient temperature of
the rack environment may be greater than room ambient
temperature. Therefore, consideration should be given to installing
the equipment in an environment compatible with the maximum
ambient temperature (Tma) specified by the manufacturer.
lReduced Airflow: Installation of the equipment in a rack should be
such that the amount of airflow required for safe operation of the
equipment is not compromised.
lMechanical Loading: Mounting of the equipment in the rack should
be such that a hazardous condition is not achieved due to uneven
mechanical loading.
1
DMPS3-4K-350-C and DMPS3-4K-250-C Series QuickStart
3-Series® DigitalMedia™ Presentation Systems

lCircuit Overloading: Consideration should be given to the
connection of the equipment to the supply circuit and the effect
that overloading of the circuits might have on overcurrent
protection and supply wiring. Appropriate consideration of
equipment nameplate ratings should be used when addressing this
concern.
lReliable Earthing: Reliable earthing of rack-mounted equipment
should be maintained. Particular attention should be given to supply
connections other than direct connections to the branch circuit
(forexample, use of power strips).
To install the device into a rack:
1. Using a #2 Phillips screwdriver and the six included 6-32 x 5/16-inch
Phillips Undercut Head screws, attach the two included rack ears to
the device (three screws for each rack ear).
2. Mount the device into the rack using four rack mount screws (not
included).
Rack Ear Attachment
Placing onto a Flat Surface
Before placing the device onto a flat surface, attach the four included feet
to the corners on the underside of the device.
Connect the Device
Connect the device as required for the application.
NOTES:
lThe DM INPUT and DM OUTPUT ports are PoDM+ power sourcing
equipment (PSE) ports and are HDBaseT PoE+ compatible. The
CONTROL SUBNET port is a PoE PSE port. Enabling PoDM+,
HDBaseT PoE+, and PoE power sourcing requires connection of the
PoDM+ INPUT PWR port to an external Crestron power supply
(PW-5430DUS or DM-PSU-3X8-RPS, sold separately). Wiring that
connects to a PoDM+, HDBaseT PoE+, or PoE PSE is designed for
intrabuilding use only.
lAs an alternative to using the main LAN port for AirMedia or H.264
content input, the CONTENT LAN port can be used to provide a
secondary LAN connection that is dedicated to either AirMedia or
H.264 content input.
Electrical Connection:
“This product must be connected to an earthed mains socket-outlet.”
lFinland: “Laite on liitettävä suojamaadoituskoskettimilla
varustettuun pistorasiaan.”
lNorway: “Apparatet må tilkoples jordet stikkontakt.”
lSweden: “Apparaten skall anslutas till jordat uttag.”
Refer to the following illustrations for connection information.
2
DMPS3-4K-350-C and DMPS3-4K-250-C Series QuickStart
3-Series® DigitalMedia™ Presentation Systems

DMPS3-4K-350-C/DMPS3-4K-350-C AIRMEDIA Rear Panel Connections
3
DMPS3-4K-350-C and DMPS3-4K-250-C Series QuickStart
3-Series® DigitalMedia™ Presentation Systems

DMPS3-4K-250-C/DMPS3-4K-250-C AIRMEDIA Rear Panel Connections
4
DMPS3-4K-350-C and DMPS3-4K-250-C Series QuickStart
3-Series® DigitalMedia™ Presentation Systems

Determine the Address of the Device
The device can be addressed using the hostname or the IP address.
Thedefault hostname is DMPS3- xxxxxxxx , where xxxxxxxx consists of the
last eight characters (excluding punctuation) of the MAC address.
Forexample, if the MAC address is 00:10:7F:08:09:AA:05, the default
hostname is DMPS3-0809AA05. The MAC address is labeled on the
shipping box and rear panel of the device.
The IP address is assigned using DHCP (Dynamic Host Configuration
Protocol), which is enabled by default. To set a static IP address, use
either of the following:
lCrestron Toolbox™ software on a PC that connects to the device via
the Ethernet network or a USB connection to the COMPUTER port on
the front panel
NOTE: The Device Discovery Tool can be used to find the current IP
address.
lThe front panel LCD display menu
Configure the Device
Using the web interface, configure the device. To access the web interface,
open a web browser and enter either of the following:
hostname /setup ( hostname is the hostname of the device)
or
xxx.xxx.xxx.xxx /setup ( xxx.xxx.xxx.xxx is the IP address of the device)
The device also provides the built-in .AV Framework™ program, which
enables complete system control without requiring additional
programming. To access the .AV Framework configuration interface,
open a web browser and go to either of the following:
hostname :8008 ( hostname is the hostname of the device appended
by :8008)
or
xxx.xxx.xxx.xxx :8008 ( xxx.xxx.xxx.xxx is the IP address of the device
appended by :8008)
For more information, go to www.crestron.com/avframework.
5
DMPS3-4K-350-C and DMPS3-4K-250-C Series QuickStart
3-Series® DigitalMedia™ Presentation Systems

Connect to the Cloud
The XiO Cloud® service allows supported Crestron devices across an
enterprise to be managed and configured from one central and secure
location in the cloud. Supported devices are preconfigured to connect to
the service. Use of the service requires a registered XiO Cloud account.
To connect the device to the XiO Cloud service:
1. Record the MAC address and serial number that are labeled on the
shipping box or rear panel of the device. The MAC address and serial
number are required in order to add the device to the XiO Cloud
environment.
2. Do either of the following:
lIf you have an XiO Cloud account, go to https://portal.crestron.io to
access the XiO Cloud service.
lIf you do not have an XiO Cloud account, go to
www.crestron.com/xiocloud to register for an account.
For detailed information about using the XiO Cloud service, refer to the
XiO Cloud® Provisioning and Management Service User Guide (Doc. 8214).
Route the Inputs
To route the inputs to one or more outputs:
1. Press the ROUTE push button.
2. Press the INPUT push button that corresponds to the input to be
routed.
3. Press the desired OUTPUT push buttons to which the input is to be
routed.
4. Press the ENTER push button.
Enable the AirMedia Presentation
Gateway (DMPS3-4K-350-C and
DMPS3-4K-250-C Only)
Enabling of the integrated AirMedia® presentation gateway of the
DMPS3-4K-350-C and DMPS3-4K-250-C requires the purchase and
activation of the SW-DMPS3-AIRMEDIA license. When enabled, the
integrated AirMedia presentation gateway eliminates the need for a
Crestron AirMedia Presentation System such as the AM-200.
NOTE: The DMPS3-4K-350-C-AIRMEDIA and DMPS3-4K-250C-
AIRMEDIA devices are shipped from the factory with the integrated
AirMedia presentation gateway already enabled and, therefore, do not
require the purchase and activation of a license.
To activate a purchased license for the AirMedia presentation gateway:
1. Obtain the system key from the AirMedia Input Configuration page of
the web interface.
2. Obtain the associated license key by visiting
www.crestron.com/dmps-airmedia-activation.
3. Enable the AirMedia presentation gateway on the AirMedia Input
Configuration page of the web interface.
For detailed information about the activation process for the AirMedia
presentation gateway, refer to Answer ID 5652 in the Online Help section
of the Crestron website.
6
DMPS3-4K-350-C and DMPS3-4K-250-C Series QuickStart
3-Series® DigitalMedia™ Presentation Systems

Visit the Product Page
Scan the QR code to visit the product page.
DMPS3-4K-350-C
www.crestron.com/model/6508338
DMPS3-4K-250-C
www.crestron.com/model/6508337
DMPS3-4K-350-C-AIRMEDIA
www.crestron.com/model/6509877
DMPS3-4K-250-C-AIRMEDIA
www.crestron.com/model/6509876
Additional Information
Original Instructions
The U.S. English version of this document is the original instructions.
All other languages are a translation of the original instructions.
Crestron product development software is licensed to Crestron dealers and Crestron
Service Providers (CSPs) under a limited nonexclusive, nontransferable Software
Development Tools License Agreement. Crestron product operating system software is
licensed to Crestron dealers, CSPs, and end-users under a separate End-User License
Agreement. Both of these Agreements can be found on the Crestron website at
www.crestron.com/legal/software_license_agreement.
The product warranty can be found at www.crestron.com/warranty.
The specific patents that cover Crestron products are listed at
www.crestron.com/legal/patents.
Certain Crestron products contain open source software. For specific information, visit
www.crestron.com/opensource.
Crestron, the Crestron logo, .AV Framework, 3-Series, AirMedia, Cresnet, Crestron
Toolbox, DigitalMedia, DM, DM 8G+, and XiO Cloud are either trademarks or
registered trademarks of Crestron Electronics, Inc. in the United States and/or other
countries. HDMI and the HDMI logo are either trademarks or registered trademarks of
HDMI Licensing LLC in the United States and/or other countries. Other trademarks,
registered trademarks, and trade names may be used in this document to refer to
either the entities claiming the marks and names or their products. Crestron disclaims
any proprietary interest in the marks and names of others. Crestron is not responsible
for errors in typography or photography.
©2020 Crestron Electronics, Inc.
Doc. 8215E
07/30/20
7
DMPS3-4K-350-C and DMPS3-4K-250-C Series QuickStart
3-Series® DigitalMedia™ Presentation Systems