Crestron AM-300 Dimensional drawing

DO GUIDE
AM-300
AirMedia®Presentation System 300
Mount Onto a Flat Surface
Use the four included anchors to mount the device onto a at surface.
NOTE: The anchors are best suited for surfaces with 3/8” to 3/4” thickness.
DO Install the Device
The AM-300 can be mounted onto a rack rail or onto a at surface.
Mount Onto a Rack Rail
Use two mounting screws (not included) to mount the left or right mounting ange of the device onto
the front or rear rail of a rack.
DO Check the Box
QTY ITEM PART NUM.
4 Anchor, Wall, Plastic, Self Drill, #8 x 1-1/4" Screw 2050199
1 Cable, USB 2.0, A - Micro B, 6' (1.83 m) 2038114
1Connector, 4-Pin 2003576
1Connector, 5-Pin 2003577
1 Power Cord, 5' 10" (1.78 m) 2042043
1 Power Pack, 24 Vdc, 2.5 A, 100-240 Vac 2045873

DO GUIDE DOC. 8253C (2050347) 05.18
Specications subject to change without notice.
DO Connect the Device
Make connections to the device as shown in the following diagrams. Use Crestron®power supplies
for Crestron equipment.
AM-300 Top Panel Connections
AM-300 Bottom Panel Connections
DO Congure the Device
Use the device’s web interface to congure the device. For details on conguring the device, refer to
the AM-200/AM-300 Product Manual (Doc. 8254) at www.crestron.com/manuals.
DO Learn More
Visit the website for additional information and the latest rmware updates. To learn
more about this product, use a QR reader application on your mobile device to scan
the QR image.
Crestron Electronics
15 Volvo Drive, Rockleigh, NJ 07647
888.CRESTRON | www.crestron.com
As of the date of manufacture, the product has been tested and found to comply with specications for CE marking.
This product is Listed to applicable UL®Standards and requirements tested by Underwriters Laboratories Inc.
Ce produit est homologué selon les normes et les exigences UL applicables par Underwriters Laboratories Inc.
This unit is for indoor use only. It is not intended for outdoor use.
Cet appareil est réservé à une utilisation en intérieur. Il n’est pas destiné à une utilisation en extérieur.
Federal Communications Commission (FCC) Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation.
CAUTION:Changes or modications not expressly approved by the manufacturer responsible for compliance could void the
user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Industry Canada (IC) Compliance Statement
CAN ICES-3(B)/NMB-3(B)
Crestron product development software is licensed to Crestron dealers and Crestron Service Providers (CSPs) under a limited non-exclusive, non-transferable Software Development Tools
License Agreement. Crestron product operating system software is licensed to Crestron dealers, CSPs, and end-users under a separate End-User License Agreement. Both of these Agreements
can be found on the Crestron website at www.crestron.com/legal/software_license_agreement.
The specic patents that cover Crestron products are listed at www.crestron.com/legal/patents.
The product warranty can be found at www.crestron.com/legal/sales-terms-conditions-warranties.
Certain Crestron products contain open source software. For specic information, visit www.crestron.com/legal/open-source-software.
Crestron, the Crestron logo, AirMedia, Crestron Toolbox, DigitalMedia, and DM are either trademarks or registered trademarks of Crestron Electronics, Inc., in the United States and/or other
countries. HDMI and the HDMI logo are either trademarks or registered trademarks of HDMI Licensing LLC in the United States and/or other countries. UL and the UL logo are either trademarks
or registered trademarks of Underwriters Laboratories, Inc. in the United States and/or other countries. Other trademarks, registered trademarks, and trade names may be used in this document
to refer to either the entities claiming the marks and names or their products. Crestron disclaims any proprietary interest in the marks and names of others. Crestron is not responsible for
errors in typography or photography.
This document was written by the Technical Publications department at Crestron.
©2018 Crestron Electronics, Inc.
HDMI®INPUT:
Digital video and
audio input
USB:
To USB accessory
DM®IN:
DigitalMedia™input Ground
HDMI OUTPUT:
To display
24 V 2.5 A:
From included power pack
CONSOLE:
To computer running
Crestron Toolbox™ Software
COM:
To serial-controlled
display device
IR 1 and IR 2:
IR 1: To IR-controlled display device
IR 2: Reserved for future use
LAN:
10/100/1000BASE-T
Ethernet to LAN