Crestron Network Device PWE-4803RU User manual

PWE-4803RU
PoE Injector
Installation Guide
4. Using a CAT5 cable, connect the LAN PoE port of the PoE injector to the PoE port of
an 802.3af compliant powered device. Refer to the following table when making
connections to the LAN PoE port.
Pin Assignments for LAN PoE Port
Introduction
Use the PWE-4803RU to power Crestron®and third party 802.3af powered devices.
Additional Resources
Visit the product page on the Crestron website (www.crestron.com)
for additional information and the latest rmware updates.
Installation
NOTE: Connect this PoE injector only to a device that is 802.3af-compliant. Plugging
this PoE injector into a device that is not 802.3af-compliant could damage the device or
the PoE injector.
1. Attach the supplied AC power cord to the IEC 320 connector on the PoE injector.
2. Insert the other end of the power cord into an active AC receptacle.
3. Using a CAT5 cable, connect the LAN port of the PoE injector to the local area
network (LAN). Refer to the following table when making connections to the LAN
port.
Pin Assignments for LAN Port
PIN SIGNAL NOTE
1 TX+ Internally wired to Pin 1 of LAN
2 TX- Internally wired to Pin 2 of LAN
3 RX+ Internally wired to Pin 3 of LAN
4 +VDC
5 +VDC
6 RX- Internally wired to Pin 6 of LAN
7 -VDC
8 -VDC
PIN SIGNAL NOTE
1 TX+ Internally wired to Pin 1 of LAN PoE
2 TX- Internally wired to Pin 2 of LAN PoE
3 RX+ Internally wired to Pin 3 of LAN PoE
4 No Connection
5 No Connection
6 RX- Internally wired to Pin 6 of LAN PoE
7 No Connection
8 No Connection
C
restron PoE Powered Device
PWE-4803RU
CAT5 Cable
CAT5 Cable
AC Power Cord
AC
Receptacle

This product is Listed to applicable UL Standards and requirements by Underwriters Laboratories Inc.
Federal Communications Commission (FCC) Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
CAUTION: Changes or modications not expressly approved by the manufacturer responsible for
compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used
in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his own expense.
Industry Canada (IC) Compliance Statement
CAN ICES-3(A)/NMB-3(A) Crestron Electronics, Inc. Installation Guide - DOC. 6712B
15 Volvo Drive Rockleigh, NJ 07647 (2021742)
Tel: 888.CRESTRON 06.15
Fax: [phone] Specications subject to
www.crestron.com change without notice.
The product warranty can be found at www.crestron.com/warranty.
The specic patents that cover Crestron products are listed at patents.crestron.com.
Crestron and the Crestron logo are either trademarks or registered trademarks of Crestron
Electronics, Inc. in the United States and/or other countries. UL and the UL logo are either trademarks
or registered trademarks of Underwriters Laboratories, Inc. in the United States and/or other
countries. Other trademarks, registered trademarks, and trade names may be used in this document
to refer to either the entities claiming the marks and names or their products. Crestron disclaims any
proprietary interest in the marks and names of others. Crestron is not responsible for errors in
typography or photography.
This document was written by the Technical Publications department at Crestron.
©2015 Crestron Electronics, Inc.