Crestron HD-RX-201-C-E Dimensional drawing

DO GUIDE
HD-RX-201-C-E
DM Lite Multiformat Switch and Receiver
DO Connect the Device
Connect the device as required for the application.
NOTES:
• A power pack is included with the HD-RX-201-C-E. If a power pack is also included with
the compatible transmitter, connect a power pack to either the receiver or transmitter.
Do not connect a power pack to both devices simultaneously. Power is transmitted over
the cable that connects the FROM TX port on the receiver to the TO RX port on
the transmitter.
• Cabling that connects the FROM TX port to the TO RX port is designed for intrabuilding
use only.
The SERVICE port on the front panel of the device is for factory use only.
DO Install the Device
Mount the device onto a at surface or rack rail.
Mount onto a Flat Surface
Using four mounting screws (not included), mount the device onto a at surface such as a wall.
Mount onto a Rack Rail
Mount the device onto the front or rear rail of a rack. Position either the left or right mounting ange
of the device so that the holes align with the holes in the rack. Then, secure the device to the rack
using two mounting screws (not included).
DO Check the Box
QTY ITEM PART NUM.
1Connector, 2-Pin 2003574
2Connector, 5-Pin 2003577
1 Power Pack, 24 Vdc 1.25 A, 100-240 Vac 2045870
HDMI:
From HDMI®
audio/video
source
FROM TX:
From TO RX
link output of
DM Lite transmitter
HDMI OUTPUT:
To HDMI
display
AUDIO:
Balanced/
unbalanced stereo
line level audio output
IR:
To IR
controllable
device
COM:
To
RS-232
device
10BASE-T/
100BASE-TX
Ethernet to
local area
network
24V
1.25A:
From included
power pack
SERVICE:
For factory
use only

DO GUIDE DOC. 7983C (2048547) 06.18
Specications subject to change without notice.
DO Congure the Device
Using the web interface, congure the HD-RX-201-C-E. The HD-RX-201-C-E also hosts the
conguration of the connected transmitter.
To access the web interface, open a web browser and then go to the IP address of the
HD-RX-201-C-E. By default, DHCP is enabled. To display the IP address on the connected HDMI®
display, press the SETUP button on the front panel of the HD-RX-201-C-E. If the transmitter has a
SETUP button, pressing the button on the transmitter will also display the IP address of the
HD-RX-201-C-E.
To log in to the web interface, enter the user name and password. The default user name and
password are both admin.
DO Learn More
Visit the website for additional information and the latest rmware updates. To learn
more about this product, use a QR reader application on your mobile device to scan
the QR image.
Crestron Electronics
15 Volvo Drive, Rockleigh, NJ 07647
888.CRESTRON | www.crestron.com
As of the date of manufacture, the product has been tested and found to comply with specications for CE marking.
This product is Listed to applicable UL®Standards and requirements tested by Underwriters Laboratories Inc.
Ce produit est homologué selon les normes et les exigences UL applicables par Underwriters Laboratories Inc.
Federal Communications Commission (FCC) Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation.
CAUTION:Changes or modications not expressly approved by the manufacturer responsible for compliance could void the user’s
authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Industry Canada (IC) Compliance Statement
CAN ICES-3(B)/NMB-3(B)
The specic patents that cover Crestron products are listed at www.crestron.com/legal/patents.
The product warranty can be found at www.crestron.com/legal/sales-terms-conditions-warranties.
Certain Crestron products contain open source software. For specic information, visit www.crestron.com/legal/open-source-software.
Crestron and the Crestron logo are either trademarks or registered trademarks of Crestron Electronics, Inc., in the United States and/or other countries. HDMI and the HDMI logo are either
trademarks or registered trademarks of HDMI Licensing LLC in the United States and/or other countries. UL and the UL logo are either trademarks or registered trademarks of Underwriters
Laboratories, Inc. in the United States and/or other countries. Other trademarks, registered trademarks, and trade names may be used in this document to refer to either the entities claiming
the marks and names or their products. Crestron disclaims any proprietary interest in the marks and names of others. Crestron is not responsible for errors in typography or photography..
This document was written by the Technical Publications department at Crestron.
©2018 Crestron Electronics, Inc.