Crestron GreenLight DIN-8SW8 How to use

Crestron Green Light™
DIN-8SW8
DIN Rail High-Voltage Switch
Operations & Installation Guide

This document was prepared and written by the Technical Documentation department at:
Crestron Electronics, Inc.
15 Volvo Drive
Rockleigh, NJ 07647
1-888-CRESTRON
Regulatory Compliance
This product is Listed to applicable UL Standards and requirements by Underwriters Laboratories Inc.
Federal Communications Commission (FCC) Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following conditions:
(1) This device may not cause harmful interference and (2) this device must accept any interference received,
including interference that may cause undesired operation.
CAUTION: Changes or modifications not expressly approved by the manufacturer responsible for compliance
could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna
Increase the separation between the equipment and receiver
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
Consult the dealer or an experienced radio/TV technician for help
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Industry Canada (IC) Compliance Statement
As of the date of manufacture, the DIN-8SW8 has been tested and found to comply with specifications for CE
marking and standards per EMC and Radiocommunications Compliance Labelling.
All brand names, product names and trademarks are the property of their respective owners.
©2010 Crestron Electronics, Inc.

Crestron DIN-8SW8 DIN Rail High-Voltage Switch
Contents
DIN Rail High-Voltage Switch: DIN-8SW8 1
Introduction ...............................................................................................................................1
Features and Functions................................................................................................1
Applications.................................................................................................................3
Specifications ..............................................................................................................4
Physical Description....................................................................................................6
Setup ..........................................................................................................................................9
Network Wiring........................................................................................................... 9
Identity Code ...............................................................................................................9
Installation.................................................................................................................10
Hardware Hookup ..................................................................................................... 12
Programming Software............................................................................................................14
Earliest Version Software Requirements for the PC ................................................. 14
Programming with Crestron SystemBuilder..............................................................14
Programming with D3 Pro.........................................................................................15
Programming with SIMPL Windows ........................................................................ 15
Example Program ......................................................................................................17
Uploading and Upgrading........................................................................................................ 18
Establishing Communication..................................................................................... 18
Programs and Firmware ............................................................................................ 19
Program Checks ........................................................................................................ 19
Operation .................................................................................................................................20
Problem Solving ......................................................................................................................22
Troubleshooting......................................................................................................... 22
Check Network Wiring..............................................................................................23
Reference Documents................................................................................................24
Further Inquiries ........................................................................................................ 24
Future Updates .......................................................................................................... 25
Return and Warranty Policies .................................................................................................. 26
Merchandise Returns / Repair Service ...................................................................... 26
CRESTRON Limited Warranty.................................................................................26
Operations & Installation Guide – DOC. 6666B Contents •i

Crestron DIN-8SW8 DIN Rail High-Voltage Switch
DIN Rail High-Voltage Switch:
DIN-8SW8
Introduction
The DIN-8SW8 is an eight channel lighting control module designed to
support switching of non-dimmable lighting and fans. A single model
supports both 120 and 220-240 Volt applications. Each channel handles
incandescent loads up to 10 Amps, fluorescent loads up to 5 Amps, and
also 1/2 HP motors.*
Features and Functions
•Eight channels of power switching
•Supports 120 to 240 Volt 50/60 Hz
•Override input
•Cresnet®communications
•Setup via front panel or software
•Programmable functionality via DIN-AP2
•9M wide DIN rail mounting
* May not be compatible with some high inrush current loads.
Operations & Installation Guide – DOC. 6666B DIN Rail High-Voltage Switch: DIN-8SW8 •1

DIN Rail High-Voltage Switch Crestron DIN-8SW8
Override Input
An override input is provided to allow an external contact closure to
momentarily override the control system program and set each channel
output to its override preset state. States can be set and saved locally from
the front panel or remotely via software.
DIN Rail Installation
The DIN-8SW8 is designed to snap onto a standard DIN rail for
installation in a wall mount enclosure. Wiring connections are made
using screw terminals positioned along the top and bottom, clearly
accessible from the front for easy installation and servicing. All setup
controls and indicators are positioned on the center front panel. When
installed in an enclosure utilizing 45 mm cutouts, the DIN-8SW8’s front
panel stays accessible while the connections are concealed.
Cresnet
The DIN-8SW8 communicates with a DIN-AP2 2-Series Automation
Processor, or other Crestron®2-Series control system, via the Cresnet
control network. A pair of Cresnet ports is provided on the DIN-8SW8
allowing for easy daisy chaining of several DIN Rail Series automation
control modules.
2•DIN Rail High-Voltage Switch: DIN-8SW8 Operations & Installation Guide – DOC. 6666B

Crestron DIN-8SW8 DIN Rail High-Voltage Switch
Applications
The following diagram shows a DIN-8SW8 in a typical application.
DIN-8SW8 in a Typical Application
Operations & Installation Guide – DOC. 6666B DIN Rail High-Voltage Switch: DIN-8SW8 •3

DIN Rail High-Voltage Switch Crestron DIN-8SW8
Specifications
Specifications for the DIN-8SW8 are listed in the following table.
DIN-8SW8 Specifications
SPECIFICATION DETAILS
Load Ratings
Switch Channels 8
Maximum Per Channel 10 Amps incandescent,
5 Amps fluorescent,
0.5 HP @ 120 to 240 Volts AC,
50/60 Hz;
5 Amps @ 30 Volts DC;
16 Amps Resistive
Module Total 80 Amps incandescent,
40 Amps fluorescent, @ 120-240
Volts AC, 50/60 Hz
Load Types1Incandescent,
magnetic low-voltage,
electronic low-voltage,
neon/cold cathode,
fluorescent, motors
Power Requirements
Cresnet Power Usage 5.4 Watts
(0.23 Amps @ 24 Volts DC)
Default Net ID 89
Minimum 2-Series
Control System Update
File2, 3
Version 4.000.0226 or later
Environmental
Temperature 0º to 40º C (32º to 104º F)
Humidity 10% to 90% RH (non-condensing)
Heat Dissipation 18 BTU/Hr
(Continued on following page)
4•DIN Rail High-Voltage Switch: DIN-8SW8 Operations & Installation Guide – DOC. 6666B

Crestron DIN-8SW8 DIN Rail High-Voltage Switch
DIN-8SW8 Specifications (Continued)
SPECIFICATION DETAILS
Enclosure Light gray polycarbonate housing
with polycarbonate label overlay,
UL94 V-0 rated, 35 mm DIN EN
60715 rail mount, DIN 43880
form factor for enclosures with
45 mm front panel cutout,
occupies 9 DIN module spaces
(162 mm)
Dimensions
Height 95 mm (3.71 in)
Width 159 mm (6.26 in)
Depth 60 mm (2.35 in)
Weight 369 g (13 oz)
Available Accessories
DIN-BLOCK DIN Rail Cresnet Distribution
Block
DIN-HUB DIN Rail Cresnet Distribution Hub
DIN-PWS50 DIN Rail 50 Watt Cresnet Power
Supply
1. May not be compatible with some high inrush current loads.
2. The latest software versions can be obtained from the Crestron website. Refer to
the NOTE following these footnotes.
3. Crestron 2-Series control systems include the DIN-AP2, AV2 and PRO2. Consult
the latest Crestron Product Catalog for a complete list of 2-Series control systems.
NOTE: Crestron software and any files on the website are for authorized
Crestron dealers and Crestron Authorized Independent Programmers
(CAIP) only. New users may be required to register to obtain access to
certain areas of the site (including the FTP site).
Operations & Installation Guide – DOC. 6666B DIN Rail High-Voltage Switch: DIN-8SW8 •5

DIN Rail High-Voltage Switch Crestron DIN-8SW8
Physical Description
This section provides information on the connections, controls and
indicators available on your DIN-8SW8.
DIN-8SW8 Physical View
DIN-8SW8 Overall Dimensions
6•DIN Rail High-Voltage Switch: DIN-8SW8 Operations & Installation Guide – DOC. 6666B

Crestron DIN-8SW8 DIN Rail High-Voltage Switch
Connectors, Controls & Indicators
# CONNECTORS*,
CONTROLS & INDICATORS
DESCRIPTION
1 1 – 8
(Connectors, LEDs and
Buttons)
(8) Sets of (2) captive screw
terminals;
Isolated Class 1 SPST relay
switch circuits 1-8;
Relay rating:
10 Amps incandescent
5 Amps fluorescent
16 Amps resistive
0.5 HP @ 120-240 Volts AC
(per channel)
Maximum wire size: 2.5 mm2
(12 AWG);
(8) Red LEDs and (8) miniature
pushbuttons for status indication
and local control of each channel
2 NET (2) 4-pin 3.5 mm detachable
terminal blocks, paralleled;
Cresnet slave port;
Connects to Cresnet control
network;
Maximum wire size: 1.5 mm2
(16 AWG);
24: Power (24 Volts DC)
Y: Data
Z: Data
G: Ground
3 NET ID
DISPLAY and CONTROL
(2) 7-Segment green LED digits
and (2) miniature pushbuttons for
setting Cresnet ID
(Continued on following page)
Operations & Installation Guide – DOC. 6666B DIN Rail High-Voltage Switch: DIN-8SW8 •7

DIN Rail High-Voltage Switch Crestron DIN-8SW8
Connectors, Controls & Indicators (Continued)
# CONNECTORS*,
CONTROLS &
INDICATORS
DESCRIPTION
4 SETUP
(LED and Button)
(1) Red LED and (1) recessed
miniature pushbutton for enabling
setup mode and touch-settable ID
5 OVERRIDE
With LEDs and Button
(2) 2-pin 3.5 mm detachable
terminal blocks, paralleled;
Maximum wire size: 1.5 mm2
(16 AWG)
Sensing input for external
low-voltage contact closure;
Activates Override mode when a
closure is present;
Minimum closure rating:
10 mA (per module) at 24 Volts;
(1) Red LED and (1) miniature
pushbutton for enabling Override
mode and saving override presets.
For more information, refer to
“Operation” which starts on page
20.
6 PWR (1) Green LED, illuminates when
DC power is applied to the NET
port
7 NET (1) Yellow LED, indicates
communication with the control
processor
8 RESET (1) Recessed miniature
pushbutton, resets internal
processor
* Interface connectors for NET and OVERRIDE ports are provided with the unit.
8•DIN Rail High-Voltage Switch: DIN-8SW8 Operations & Installation Guide – DOC. 6666B

Crestron DIN-8SW8 DIN Rail High-Voltage Switch
Setup
Network Wiring
When wiring the Cresnet network, consider the following:
•Use Crestron Certified Wire.
NOTE: Cresnet HP cannot be used.
•Use Crestron power supplies for Crestron equipment.
•Provide sufficient power to the system.
CAUTION: Insufficient power can lead to unpredictable results
or damage to the equipment. Please use the Crestron Power
Calculator to help calculate how much power is needed for the
system (www.crestron.com/calculators).
•Use of a Cresnet hub/repeater (DIN-HUB) is advised whenever the
number of Cresnet devices on a network exceeds 20 or when the
combined total length of Cresnet cable exceeds 914 meters (3000
feet).
For more details, refer to “Check Network Wiring” which starts on page
23.
Identity Code
The Net ID of the DIN-8SW8 has been factory set to 89. The Net IDs of
multiple DIN-8SW8 devices in the same system must be unique. Net IDs
are changed from a personal computer (PC) via Crestron Toolbox™
(refer to “Establishing Communication” on page 18).
To set the Net ID using the front panel:
1. Press the SETUP button to enter the Setup mode. The SETUP
LED illuminates.
2. Press the left button under the NET ID display to change the most
significant digit of the Net ID or press the right button under the
NET ID display to change the least significant digit of the Net ID
number.
Operations & Installation Guide – DOC. 6666B DIN Rail High-Voltage Switch: DIN-8SW8 •9

DIN Rail High-Voltage Switch Crestron DIN-8SW8
3. When the desired Net ID is displayed, press the SETUP button to
exit the Setup mode. The SETUP LED extinguishes.
NOTE: If an invalid Net ID is set (00, 02, FF), “Er” will be
displayed on the NET ID display. The DIN-8SW8 will revert to
the previously set Net ID.
NOTE: The DIN-8SW8 will leave the Setup mode after 10
seconds of inactivity. The DIN-8SW8 will revert to the previously
set Net ID.
NOTE: A small label (with numbers and letters) is provided on
the front panel of the DIN-8SW8 to document the unit’s Net ID in
the case where power is not available. Apply a mark over the digits
that correspond to the assigned Net ID.
NET ID Label (“3C” Shown)
When setting the Net ID, consider the following:
•The Net ID of each unit must match an ID code specified in the
SIMPL™ Windows®program.
•Each network device must have a unique Net ID.
For more details, refer to the Crestron Toolbox help file.
Installation
The DIN-8SW8 must be installed by a licensed electrician, in accordance
with all national and local codes.
CAUTION: This equipment is for indoor use only. Mount in a well
ventilated area. The ambient temperature must be 0º to 40º C
(32º to 104º F). The relative humidity must be 10% – 90%
(non-condensing).
NOTE: When installing in an enclosure, high-voltage devices should be
grouped separately from low-voltage devices.
10 •DIN Rail High-Voltage Switch: DIN-8SW8 Operations & Installation Guide – DOC. 6666B

Crestron DIN-8SW8 DIN Rail High-Voltage Switch
The DIN-8SW8 is designed for installation on a DIN rail. Refer to the
following diagram when installing.
Installing the DIN-8SW8
1. Place the top of the DIN-8SW8’s rail mount over the top of the
DIN rail.
2. Tilt the bottom of the DIN-8SW8 toward the DIN rail until it snaps
into place.
NOTE: When mounting DIN rail products, it may be necessary to
use a flat-head screwdriver to pull the DIN rail release tab while
snapping the device onto the DIN rail.
To remove the DIN-8SW8 from the DIN rail, use a small, flat object (i.e.,
a flat-head screwdriver) to pull the DIN rail release and tilt the bottom of
the DIN-8SW8 away from the DIN rail.
NOTE: Certain third party DIN cabinets provide space for an
informational label between each DIN rail row. Crestron’s Engraver
software (version 4.0 or later) can generate appropriate labels for all
Crestron DIN rail products.
Operations & Installation Guide – DOC. 6666B DIN Rail High-Voltage Switch: DIN-8SW8 •11

DIN Rail High-Voltage Switch Crestron DIN-8SW8
Hardware Hookup
Make the necessary connections as called out in the illustration that
follows this paragraph. Refer to “Network Wiring” on page 9 before
attaching the 4-position terminal block connector. Apply power after all
connections have been made.
WARNING: Prior to connecting the device, turn off power at the circuit
breaker. Failure to do so may result in serious personal injury or damage
to the device. Restore power after all connections have been made.
CAUTION: Connecting this device to the wrong type of load or
short-circuiting the load can cause severe product damage. Each load
should be tested to identify a short circuit condition prior to wiring the
load to the module.
NOTE: Install in accordance with all local and national electric codes.
NOTE: High-voltage connections accept 2.5 mm2(12 AWG) wire. Wire
should be stripped to 8 mm (1/3 inch). Tighten terminal blocks to 0.5 Nm
(5 in-lbs).
NOTE: Use copper wire only. For high-voltage connections, use wire
rated for at least 75º C (167º F).
NOTE: Each switch leg of the DIN-8SW8 may be fed from a separate
circuit breaker.
When making network connections to the DIN-8SW8, use a Crestron
power supply.
12 •DIN Rail High-Voltage Switch: DIN-8SW8 Operations & Installation Guide – DOC. 6666B

Crestron DIN-8SW8 DIN Rail High-Voltage Switch
Hardware Connections for the DIN-8SW8
NET:
To Control System and
Other Cresnet Devices
OVERRIDE:
From Device Providing Override
Signal and to Other Devices
Receiving Override Signal
1 - 8:
Connections for
Controlled Devices
With the circuit breaker turned off, connect the wires to the terminal
blocks per the markings provided on the DIN-8SW8.
Load Connection Example for the DIN-8SW8
Operations & Installation Guide – DOC. 6666B DIN Rail High-Voltage Switch: DIN-8SW8 •13

DIN Rail High-Voltage Switch Crestron DIN-8SW8
Programming Software
Have a question or comment about Crestron software?
Answers to frequently asked questions (FAQs) can be viewed in the
Online Help section of the Crestron website. To post a question or view
questions you have submitted to Crestron’s True Blue Support, log in at
www.crestron.com/support. First-time users will need to establish a user
account.
Earliest Version Software Requirements for the
PC
NOTE: Crestron recommends that you use the latest software to take
advantage of the most recently released features. The latest software is
available from the Crestron website (www.crestron.com/software).
Crestron has developed an assortment of Windows-based software tools
to develop a Cresnet system. You can create a program to control the
DIN-8SW8 using the Crestron programming tools Crestron
SystemBuilder™, D3 Pro®or SIMPL Windows. Customers whose focus
is on lighting systems may prefer to use the D3 Pro software since it is
designed especially for creating lighting and environmental system
control applications. Customers already familiar with SIMPL Windows
who are including a lighting system as part of an overall control system
project may prefer to continue using SIMPL Windows. For the minimum
recommended software versions, visit the Version Tracker page of the
Crestron website (www.crestron.com/versiontracker).
Programming with Crestron SystemBuilder
Crestron SystemBuilder is the easiest method of programming but does
not offer as much flexibility as SIMPL Windows. For additional details,
download SystemBuilder from the Crestron website and examine the
extensive help file.
14 •DIN Rail High-Voltage Switch: DIN-8SW8 Operations & Installation Guide – DOC. 6666B

Crestron DIN-8SW8 DIN Rail High-Voltage Switch
Programming with D3 Pro
Crestron’s D3 Pro lighting software provides all the tools necessary to
create a complete Crestron lighting system for residential applications.
The lighting system includes the control system logic program,
touchpanel projects and keypad programming, documentation and real-
time lighting adjustment capabilities.
As with all Crestron software, D3 Pro provides extensive right-click and
drag-and-drop functionality in addition to convenient keyboard shortcuts
for frequently used functions and commands.
Programming is organized into six system Views of the lighting system,
each providing a moveable toolbox of devices such as interfaces, fixtures
and control modules. You can add a device to your system simply by
selecting it from one of the toolboxes and dragging it to a room. The
available toolboxes differ depending on the View but all Views include a
"General" toolbox that allows you to add areas and rooms at any time.
Programming with SIMPL Windows
NOTE: While SIMPL Windows can be used to program the DIN-8SW8,
it is recommended to use SystemBuilder for configuring a system.
SIMPL Windows is Crestron’s premier software for programming
Crestron control systems. It is organized into two separate but equally
important “Managers”.
Configuration
Manager
Configuration Manager is the view where programmers “build” a
Crestron control system by selecting hardware from the Device Library.
1. To incorporate the DIN-8SW8 into the system, drag the
DIN-8SW8 from the Lighting | Lighting (DIN-Rail Series) folder
of the Device Library and drop it in the System Views.
Operations & Installation Guide – DOC. 6666B DIN Rail High-Voltage Switch: DIN-8SW8 •15

DIN Rail High-Voltage Switch Crestron DIN-8SW8
Locating the DIN-8SW8 in the Device Library
2. The system tree of the control system displays the device in the
appropriate slot with a default Net ID as shown in the following
illustration.
C2Net-Device, Slot 5
3. Additional DIN-8SW8 devices are assigned different Net ID
numbers as they are added.
16 •DIN Rail High-Voltage Switch: DIN-8SW8 Operations & Installation Guide – DOC. 6666B