Crestron TSS-752 User manual

Crestron TSS-752
7” Room Scheduling Touch Screen
Configuration Guide

The specific patents that cover Crestron products are listed at patents.crestron.com.
Crestron, the Crestron logo, Rava, and RoomView are either trademarks or registered trademarks of Crestron Electronics, Inc. in the United States
and/or other countries. Other trademarks, registered trademarks, and trade names may be used in this document to refer to either the entities claiming
the marks and names or their products. Crestron disclaims any proprietary interest in the marks and names of others. Crestron is not responsible for
errors in typography or photography.
This document was written by the Technical Publications department at Crestron.
©2014 Crestron Electronics, Inc.

Crestron TSS-752 7” Room Scheduling Touch Screen
Configuration Guide – DOC. 7602A Contents •i
Contents
7” Room Scheduling Touch Screen: TSS-752 1
Access the Setup Screens........................................................................................................... 1
Configure the Touch Screen ...................................................................................................... 3
Ethernet Setup .............................................................................................................3
IP Table Setup .............................................................................................................5
Audio Setup.................................................................................................................7
Display Setup .............................................................................................................. 7
Standby Timeout .........................................................................................................8
Diagnostics ..................................................................................................................9
About ......................................................................................................................... 14
Save & Exit ............................................................................................................... 14

Crestron TSS-752 7” Room Scheduling Touch Screen
Configuration Guide – DOC. 7602A 7” Room Scheduling Touch Screen: TSS-752 •1
7” Room Scheduling
Touch Screen: TSS-752
Access the Setup Screens
The “TSS-752 Setup” menu is the starting point for configuring the TSS-752 Room
Scheduling Touch Screen from Crestron®.
NOTE: If no project has been loaded or if an invalid project has been loaded, the
TSS-752 displays a message instructing the user to touch the screen to enter the
setup menus.
The setup screens enable basic configuration procedures prior to regular operation of
the touch screen. To access the setup screens after the TSS-752 boots up to the
RoomView®Scheduling “Offline” screen, touch “hard keys” 1, 2, 3, and 4, to the
right of the touch screen display, in sequence twice (touch 1, 2, 3, 4, 1, 2, 3, 4) within
a 5-second period.
Button Numbering
4
3
2
1

7” Room Scheduling Touch Screen Crestron TSS-752
2•7” Room Scheduling Touch Screen: TSS-752 Configuration Guide – DOC. 7602A
The “TSS-752 Setup” menu is displayed.
“TSS-752 Setup” Menu
The “TSS-752 Setup menu” is comprised of buttons for Ethernet Setup, IP Table
Setup, Audio Setup, Display Setup,Standby Timeout and Diagnostics. In
addition, there is a User Project Mode On button to toggle the RoomView
Scheduling interface, an About button that provides information about the touch
screen and a Save & Exit button. The functions are detailed in the next section of
this guide.

Crestron TSS-752 7” Room Scheduling Touch Screen
Configuration Guide – DOC. 7602A 7” Room Scheduling Touch Screen: TSS-752 •3
Configure the Touch Screen
Ethernet Setup
On the “TSS-752 Setup” menu, touch Ethernet Setup to display the “Ethernet
Setup” menu.
“Ethernet Setup” Menu
The “Ethernet Setup” menu displays the touch screen’s MAC address and IP
Address, Subnet Mask, Def Router, Primary DNS, Secondary DNS, Hostname and
Domain. There are controls for turning DHCP On or Off as well as a Set Static IP
Address Settings button, which provides access to controls which allow editing of
these settings. This screen also contains a Link indicator to show the status of the
Ethernet connection.
NOTE: Crestron recommends using a static IP address for anything other than
testing.
DHCP is enabled by default. To change to a static IP address, touch Off under
DHCP Enabled, then touch Set Static IP Address Settings to display the “Ethernet
Setup – Static IPs” screen.

7” Room Scheduling Touch Screen Crestron TSS-752
4•7” Room Scheduling Touch Screen: TSS-752 Configuration Guide – DOC. 7602A
“Ethernet Setup – Static IPs” Screen
To edit the Static IP Address, Static Subnet Mask, Static Default Router, Preferred
DNS or Alternate Preferred DNS, touch the button directly under the label for the
entry to edit. The on-screen numeric keypad opens.
On-Screen Numeric Keypad
Use the keypad to make the new entry. Touch the “x” in the text field to clear any
previous entry. Touch to delete the last digit. Touch Save to save a new entry
or to return to the “Ethernet Setup – Static IPs” screen.
After new settings have been saved, touch Reboot Required to Apply IP Changes
on the “Ethernet Setup – Static IPs” screen to reboot the touch screen, so the new
settings can take effect.
If not making any changes, touch to return to the “Ethernet Setup” menu.
Touch again to return to the “TSS-752 Setup” menu.

Crestron TSS-752 7” Room Scheduling Touch Screen
Configuration Guide – DOC. 7602A 7” Room Scheduling Touch Screen: TSS-752 •5
IP Table Setup
On the “TSS-752 Setup” menu, touch IP Table Setup to display the “Ethernet Setup
– IP Table” menu.
“Ethernet Setup –IP Table” Menu
NOTE: This step should not be performed when the TSS-752 is being used for
RoomView scheduling, as having an IP table entry will prevent the project from
starting up.
The “Ethernet Setup – IP Table” menu displays up to four IP table settings, each of
which has an Online indicator. To add or edit an entry, touch the Add/Edit button to
its left. The “Ethernet Setup – Edit IP Table Entry” screen is displayed.
“Ethernet Setup –Edit IP Table Entry” Screen
Touch the field below CIP ID to display the on-screen hex keypad.

7” Room Scheduling Touch Screen Crestron TSS-752
6•7” Room Scheduling Touch Screen: TSS-752 Configuration Guide – DOC. 7602A
On-Screen Hex Keypad
Use the keypad to make the new entry. Touch the “x” in the text field to clear any
previous entry. Touch to delete the last digit. Touch Save to save a new entry
or to return to the “Ethernet Setup – Edit IP Table Entry” screen.
Touch the field below IP Address/Hostname to display the on-screen keyboard.
On-Screen Keyboard
Use the keyboard to make the new entry. Touch Cancel to return to the “Ethernet
Setup – Edit IP Table Entry” screen. Touch the “x” in the text field to clear any
previous entry. Touch to delete the last digit. Touch Save to save a new entry
and return to the “Ethernet Setup – Edit IP Table Entry” screen.
On the “Ethernet Setup – Edit IP Table Entry” screen, touch Save Entry to save the
current entry or Delete Entry to clear it.
If not making any changes, touch to return to the “Ethernet Setup –IP
Table” menu.
Touch again to return to the “TSS-752 Setup” menu.