Crestron TSW-552 Dimensional drawing

DO GUIDE
DO Check the Box
QTY PART NUM.
1TSW-UMB Universal Mounting Bracket 4517962
1Pre-Construction Bracket 2035648
TSW-552
5" Touch Screen
DO Install the Device
The TSW-552 can be mounted into drywall and other surfaces
or mounted onto a wall stud. When mounted into drywall and
other surfaces, the touch screen protrudes just 1/2” (13 mm)
from the mounting surface.
To mount the TSW-552, use the following procedure:
1. For pre-construction applications, use standard drywall
nails or screws to attach the included pre-construction
bracket to a wall stud.
Pre-Construction Bracket Attached to a Wall Stud
CAUTION: Allow an air gap of at least 12” (305 mm) in
the wall cavity above and below the TSW-552 for heat
dissipation.
For post-construction applications, use the
pre-construction bracket as a cutout template by turning
the bracket to face the wall, ensuring it is level, and
temporarily tacking it to the wall with nishing nails (not
included) in the smaller holes around the cutout opening.
Trace the cutout opening with an appropriate drywall saw
(not included).
Post-Construction Installation of the TSW-UMB Universal Mounting
Bracket into a Cutout
2. Loosen the two screws on the included TSW-UMB
Universal Mounting Bracket, and then install the
TSW-UMB bottom rst into the opening.
Installing the TSW-UMB
3. Reach into the TSW-UMB and push the rear half back
to ensure it is fully behind the mounting surface. Ensure
the front of the TSW-UMB is level. Then, tighten the two
screws to complete the installation.
CAUTION: To avoid damage to the bracket, do not
overtighten the screws.
Completing the TSW-UMB Installation
4. Make connections to the TSW-552 using Crestron®
power supplies and Crestron equipment. Power and
data connection to the TSW-552 is provided by a single
Ethernet cable connected to the LAN port at the rear of
the unit. A Crestron PoE power supply or PoE-capable
network switch is recommended (both sold separately).
Apply power after the Ethernet cable is connected.
Hardware Connections for the TSW-552
5. Carefully hold the touch screen over the TSW-UMB and
gently place it in position. The magnets on the rear of the
touch screen hold it in place on the TSW-UMB.
Pre-Construction Bracket
Use a tie wrap to hold the cable
until the TSW-552 is mounted.
TSW-UMB
Push the top surface
downward to install
the bottom half rst.
TSW-UMB
Loosen both of the screws.
Push the rear half back.
Ensure the front is level.
Then, tighten both screws.
Reset Button
LAN PoE:
10BASE-T /
100BASE-TX
Ethernet to LAN

DO GUIDE DOC. 7659A (2043930) 05.15
Specications subject to change without notice.
DO Access the Setup Screens
NOTE: The TSW-552 can take up to 120 seconds to boot.
When power is applied for the rst time, the screen shown in
the following illustration appears.
Tap the Setup button to display the TSW-552 Setup screen.
The setup screens enable basic conguration procedures
prior to regular operation of the TSW-552.
NOTE: During regular operation of the touch screen, there
are two ways to activate the setup functions:
1. Place a button on the project main page and assign the
reserved join number (17242) that activates setup.
2. Press the hard keys labeled below as 1, 2, 3, and 4 in
sequence twice (press 1, 2, 3, 4, 1, 2, 3, 4) within a 5
second period.
NOTE: For details on conguring the TSW-552, refer to Doc.
7578 at www.crestron.com/manuals.
DO Learn More
Visit the website for additional information
and the latest rmware updates.
Crestron Electronics
15 Volvo Drive, Rockleigh, NJ 07647
888.CRESTRON | www.crestron.com
As of the date of manufacture, the product has been tested and found to comply with specications for CE marking.
Federal Communications Commission (FCC) Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following conditions:
(1) This device may not cause harmful interference and (2) this device must accept any interference received, including interference
that may cause undesired operation.
Caution: Changes or modications not expressly approved by the manufacturer responsible for compliance could void the user’s
authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help
Industry Canada (IC) Compliance Statement
CAN ICES-3(B)/NMB-3(B)
Crestron product development software is licensed to Crestron dealers and Crestron Service Providers (CSPs) under a limited non-exclusive, non-transferable Software Development Tools
License Agreement. Crestron product operating system software is licensed to Crestron dealers, CSPs, and end-users under a separate End-User License Agreement. Both of these Agreements
can be found on the Crestron website at www.crestron.com/legal/software_license_agreement.
The specic patents that cover Crestron products are listed at patents.crestron.com. The product warranty can be found at www.crestron.com/warranty.
Crestron and the Crestron logo are either trademarks or registered trademarks of Crestron Electronics, Inc. in the United States and/or other countries. Other trademarks, registered trademarks,
and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Crestron disclaims any proprietary interest in the marks and names
of others. Crestron is not responsible for errors in typography or photography.
This document was written by the Technical Publications department at Crestron.
©2015 Crestron Electronics, Inc.
1
2
3
4