Croydex Luxury Round Shower Curtain Rod AD116541 User manual

Luxury Round Shower Curtain Rod
Thank you for purchasing this Croydex product. Please follow the fixing and care instructions to
ensure that your curtain rod is fitted safely and it retains its high quality finish. Please retain this
leaflet for future reference.
Tools Required
Drill; 6mm masonry drill bit; 6mm ceramic drill bit (optional); Screwdriver; Pencil; Spirit level; Small
hack saw; Hex head keys (included in fixing pack)
Keep DIY tools out of reach of children
Fixing Pack
A. Fixing screw x 2
B. Wall plug x 2
C. Hex head key x 2 (large & small)
D. Spare grub screw x 2
Pack Contents
E. Wall bracket x 2
F. Wall bracket cover x 2
G. Hooks x 12
H. Straight Joint x 1
I. 1.25m Rod x 2
Home Safety Advice
Before drilling, check for hidden cables or pipes. The use of a residual current device (RCD) is
recommended when working with power tools.
If the product is to be fitted on a ceramic tiled wall, a ceramic drill bit should be used. Always
ensure that the drill hole passes through the central tiled area rather than the grouted area. To
prevent damage to the tile, mask the area around the hole with tape before drilling.
Do not use this product as a grab bar.
We recommend that two people fit this product to ensure that it is fitted safely.
The rod has been packed with the wall brackets and covers already attached to each end of the
rod.
Product Care
To retain the best quality finish, clean product regularly with a soft cloth and mild detergents.
Do not use abrasive or chemical cleaners as these will damage the product.
A.
D.
C.
B.
E.
F.
G.
H.
I.

Fitting Instructions
1. The rod is supplied as two 1.25m lengths which can be joined together
using the straight joint provided. Firstly lay the two rods down on a flat
level surface. One end of each of the rods has a hole pierced into it
approximately 50mm from the end. Insert the straight joint into one of
these ends so that the grub screw is central with the hole in the rod.
Using the larger of the two hex head keys, provided, rotate the grub
screw clockwise until the straight joint is clamped tightly in position
(see Fig. 1).
2. Assemble the second rod onto the straight joint making sure that the
tube ends are pushed tightly together, align the hole with the grub screw
and again clamp tightly in position (see Fig. 2).
3. Select desired position of rod and mark centres of the mounting
holes using the wall brackets as a template (see Fig. 3)
Make sure that the wall brackets are level with each other before drilling.
4. Using a 6mm masonry drill, drill the holes in the marked positions to a
depth of 40mm. If drilling through tiles, please pre-drill using a ceramic
drill bit.
5. Insert the wall plugs to the surface of the wall. If fitting to a tiled surface,
the wall plug should be inserted below the surface of the tile to avoid
cracking.
6. Accurately measure the distance between the fixing surfaces. Carefully
cut one end of the assembled rod 42 mm shorter than the measured
distance between the fixing surfaces. See fig 4. Ensure the end of the rod
is cut square and the cut edge is de-burred.
7. Position the hooks and wall bracket covers onto the rod making
sure they are in the correct orientation. Locate the rod between the
wall brackets and slide each wall bracket cover onto the wall brackets.
Secure each wall bracket cover in position by tightening the grub
screw closest to the wall (a).
Once these are secured rotate the rod so that the pierced holes
are at the top and then tighten the second grub screw (b) in each
wall bracket cover (see Fig. 5).
8. Check that the wall brackets are level by placing a spirit level onto
the rod.
9. The rod is now ready to hang a curtain.
10. If required lightly apply silicone polish to the top of the rail to reduce hook friction.
Croydex Ltd, Central Way, Andover,
Hampshire, SP10 5AW, United Kingdom
Website: www.croydex.com
E-Mail: [e-mail]
R&R 002 R02
Fig.5
Fig.4
Fig.3
Fig.2
Fig.1