CRU Dataport Rugged, Reliable, Mobile, Secure DataPort 2... User manual

Rugged, Reliable, Mobile, SecureTM
1-800-260-9800 www.CRU-DataPort.com
DataPort 2 and 4 Bay Enclosure
Install Guide
The DataPort 2 & 4 Bay Enclosures include the following pieces.
If any items are missing or damaged please contact CRU for a
replacement.
4 Bay Enclosure Package Contents
1 - External Enclosure
1 - U320 LVD Terminator
1 - External U320 VHD to UVHD Cable
4 - Hard Drive Mounting Rails
1 - Installation Guide
2 Bay Enclosure Package Contents
1 - External Enclosure
1 - U320 LVD Terminator
1 - External U320 VHD to UVHD Cable
2 - Hard Drive Mounting Rails
1 - Installation Guide
Enclosure Set Up
1. Remove the cover of the DataPort Enclosure. Remove the rear
screws and slide the cover off the back of the enclosure.
2. Remove the front bezels if you are installing a device that
needs external access such as a tape back up unit or CD-ROM.
The DataPort 2 and 4 Bay SCSI Enclosures allow external SCSI devices to be easily
added to any system with an available external SCSI channel. The DataPort Enclo-
sures can provide additional tape backup units, CD-ROMs or non-removable hard
drives to a server. The DataPort 2 and 4 Bay Enclosures will support most full height
SCSI tape backup units. For adding removable DataPort hard drives please contact
CRU at www.CRU-DataPort.com.
3. Set the SCSI ID on the device or remove the jumpers and use
the provided SCSI ID selector switch. Do not use SCSI ID #7, it
is used by SCSI Host Bus Adapters.
4. Install the hard drive mounting kits and secure them with the
provided screws. Otherwise install the SCSI device into the
enclosure and secure them with the provided screws.
5. Connect the data and power cables to the back of the SCSI
devices. If needed connect the SCSI ID selector switches.
6. Slide the cover back on and secure it with the screws.
7. Connect the external power cable, the SCSI cable and
Terminator.
Your enclosure is now setup and ready for use.

Rugged, Reliable, Mobile, SecureTM
1-800-260-9800 www.CRU-DataPort.com
Operation
For best results, power on your SCSI Enclosure before powering
on your computer system. The power switch is located on the
bottom front of the enclosure.
The DataPort SCSI Enclosure is also equipped with 2 or 4 external
SCSI ID selector switches. These allow you to externally set the
SCSI ID number from the back of the enclosure. There are two
buttons on each switch for increasing or decreasing the SCSI ID
number. Make sure the SCSI device is set to zero before using the
selector on the back of the enclosure.
Please note that while the CRU-DataPort 4 bay enclosure has 5 avail-
able bays it is currently cabled to support 4 SCSI devices.
Technical Support
Contact your dealer for technical support first. If you still need
assistance, contact the CRU-DataPort technical support depart-
ment. You can contact our technical support department by
visiting our web site at http://www.CRU-DataPort.com, sending
an E-mail message to [email protected] or calling
technical support at:
[phone] during the hours of: 8:00 AM to 5:00 PM, PST
Monday through Friday.
When you call, please have the following information ready:
• The part number of your CRU-DataPort product(s).
• The manufacturer’s name and model number of the hard
disk drive and the computer system you are using.
• The name of the dealer from which you purchased your
CRU product(s).
• Any error messages that appeared on your screen.
Product Warranty
CRU-DataPort (CRU) warrants the DataPort 2 & 4 bay enclosure
to be free of significant defects in material and workmanship for
a period of one year from the original date of purchase. CRU’s
warranty is nontransferable and is limited to the original pur-
chaser.
Limitation of Liability
The warranties set forth in this agreement replace all other war-
ranties. CRU expressly disclaims all other warranties, including
but not limited to, the implied warranties of merchantability and
fitness for a particular purpose and non-infringement of third-
party rights with respect to the documentation and hardware.
No CRU dealer, agent or employee is authorized to make any
modification, extension, or addition to this warranty. In no event
will CRU or its suppliers be liable for any costs of procurement
of substitute products or services, lost profits, loss of informa-
tion or data, computer malfunction, or any other special, indirect,
consequential, or incidental damages arising in any way out of
the sale of, use of, or inability to use any CRU product or service,
even if CRU has been advised of the possibility of such damages.
In no case shall CRU’s liability exceed the actual money paid for
the products at issue. CRU reserves the right to make modifica-
tions and additions to this product without notice or taking on
additional liability.
Register your product at www.CRU-DataPort.com.
A5-024-0001 Rev. 1.1