CrustBuster Seed Tender 160 User manual

P.O. Box 526 - Spearville, Kansas 67876 - [phone]
crustbuster.com
160 & 240
Seed Tender
OWNER'S
MANUAL
#17993700 (2010) Updated (2020)

Table of Contents
Warranty Information . . . . Inside Front Cover
Operator Qualifications . . . . . . . . . . . . . . . . . 1
Safety ............................ 2-6
Operation, Maintenance, & Belt Training . 7-8
BeltAssembly........................ 9
Dimensions...................... 10-11
Repair Parts
Tank
160 Electric. . . . . . . . . . . . . . . . . 12-15
160Gas ...................16-19
240 Electric. . . . . . . . . . . . . . . . . 20-23
240Gas ...................24-27
Head & Tail
160 & 240 Electric (Prior 2021) . 28-29
160 & 240 Gas (Prior 2021) . . . . 30-31
160 Electric. . . . . . . . . . . . . . . . . 32-33
240 Electric. . . . . . . . . . . . . . . . . 34-35
160 Gas . . . . . . . . . . . . . . . . . . . 36-37
240 Gas . . . . . . . . . . . . . . . . . . . 38-39
Telescoping Tube
160 & 240 Gas . . . . . . . . . . . . . . 40-45
Cables & Tube Straps 160. . . . . . . . 46-47
Cables & Tube Straps 240. . . . . . . . 48-49
Engine Assemblies. . . . . . . . . . . . . . 50-51
Flexible Feed Spout . . . . . . . . . . . . . . . 52
Talc 160 & 240 . . . . . . . . . . . . . . . . . . . 53
Index 160 . . . . . . . . . . . . . . . . . . . . . 53-54
Seed Ladders . . . . . . . . . . . . . . . . . . . . 54
Remote Control . . . . . . . . . . . . . . . . 55-61
Trailer’s. . . . . . . . . . . . . . . . . . . . . . . 61-67

Identification
Your Seed Tender is identified by a Serial Number and Model Number. Record these numbers in the
spaces provided in this manual and refer to them when ordering parts or requesting service.
Serial Number Model Number
Warranty
WARRANTY: In addition to the implied warranties of fitness and of merchantability, CrustBuster®/Speed
King, Inc. warrants new products sold by it to be free from defects in workmanship and material for a period
of 12 months, from the date of delivery to the first user customer. Warranty on purchased parts (cylinder,
blades, bearings, shanks, etc.) will be the same as that offered by the appropriate manufacturer of these
parts.
EXCLUSIONS: No warranty of any kind is made by CrustBuster®/Speed King, Inc. with regard to new
products which have been subject to operation in excess of recommended capacities, misuse, abuse,
negligence, or accident, or have been altered or repaired in any manner not authorized by
CrustBuster®/Speed King, Inc. CrustBuster®/Speed King, Inc. is constantly striving to improve its products.
Changes in design and improvement will be made whenever CrustBuster®/Speed King, Inc. believes the
efficiency of its products will be improved thereby, but without incurring any obligation to incorporate such
improvements in any products which have been shipped or are in service. No obligation exists for
compensation of unauthorized repairs or modifications without prior approval. And in no event will
CrustBuster®/Speed King, Inc. be liable for consequential damages, such as but not limited to: downtime,
delayed or late tillage or planting, etc.
WARRANTY REGISTRATION: This warranty is not valid unless registered with CrustBuster®/Speed King,
Inc. within 10 days from the date of purchase. It is the sole responsibility of the selling retail dealer to fill out
the registration forms and see that they are properly filed with CrustBuster®/Speed King, Inc. This can be
done at crustbuster.com.
WARRANTY PROCEDURE: Should any part fail to conform with this warranty, CrustBuster®/Speed King,
Inc. will repair or replace the part or parts which do not conform. If a part is defective, take it to your
authorized CrustBuster® Farm Equipment Dealer immediately, along with your warranty registration, and
complete the proper forms requesting a warranty adjustment. Our representative will pick up the part to be
returned to the factory for examination. If the customer (first user) requests that a new part be substituted
for the old part, a new part will be charged to the dealer who will in turn charge the customer. If the part is
found by us to be defective, a credit for the part will be given to the dealer to be passed on to the customer.
If the dealer or customer wishes to repair the part, this will be done only if authorized by
CrustBuster®/Speed King, Inc. This warranty procedure is in addition to all remedies authorized by law.
CRUST BUSTER®/SPEED KING, INC.
Box 526
Spearville, KS 67876
Specifications are subject to change without notice. ® is a registered trademark of CrustBuster/Speed King,Inc

Operator Qualifications
Operation of this Seed Tender shall be limited to competent and experienced persons. In addition,
anyone who will operate or work around this equipment must use good common sense. In order to be
qualified, he or she must also know and meet all other requirements, such as:
1. Some regulations specify that no one under the age of 16 may operate power
machinery. It is your responsibility to know what these regulations are in your
area or situation.
2. Current OSHA regulations state in part: "At the time of initial assignment and at
least annually thereafter the employer shall instruct EVERY employee in the safe
operation of servicing of all equipment with which the employer is, or will be
involved."
3. Unqualified persons are to STAY OUT of the work area.
4. A person who has not read and understood all operating and safety instructions
is not qualified to operate the machinery.
FAILURE TO READ THIS SEED TENDER MANUAL AND ITS
SAFETY INSTRUCTIONS IS A MISUSE OF THE EQUIPMENT.
Sign Off Sheet
As a requirement of OSHA, it is necessary for the employer to train the employee in the safe operation
and safety procedures with this Seed Tender. We include this sign off sheet for your convenience and
personal record keeping.
DATE EMPLOYER EMPLOYER'S SIGNATURE
1

BE ALERT!
Your Safety is involved.
General Safety Statement
WATCH FOR THIS SYMBOL. IT POINTS OUT IMPORTANT SAFETY
PRECAUTIONS. IT MEANS "ATTENTION )) ) BECOME ALERT!"
YOUR SAFETY IS INVOLVED.
It is your responsibility as an owner, operator, or supervisor to know and instruct everyone using
this Seed Tender at the time of initial assignment and at least annually thereafter, of the proper
operation, precautions, and work hazards which exist in the operation of this Seed Tender in
accordance with OSHA Regulations.
Safety Is No Accident
The following safety instructions, combined with common sense, will save your equipment from
needless damage and the operator from unnecessary exposure to personal hazard. Pay special
attention to the caution notes in the text. Review this manual at least once each year with new
and/or experienced operators.
1. Read and understand the operator's manual before operating this Seed Tender.
Failure to do so is considered a misuse of the equipment.
2. Make sure Seed Tender is secure before operating.
3. Always keep children away from Seed Tender when operating.
4. Make sure everyone that is not directly involved with the operation is out of the
work area before beginning the operation.
5. Make sure all safety devices, shields, and guards are in place and are functional
before beginning the operation.
6. Shut off power to adjust, service, or clean.
7. Keep hands, feet, and clothing away from moving parts. It is a good idea to
remove all jewelry before starting the operation.
8. Visually inspect the Seed Tender periodically during operation for signs of
excessive vibration, loose fasteners, and unusual noises.
DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death
or serious injury.
WARNING: Indicates a hazardous situation which, if not avoided, could result in death or serious
injury.
CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor
or moderate injury.
NOTICE: Used to address practices not related to physical injury.
2

CAUTION
1. Read and understand instruction manual before operating.
2. Keep all safety shields and devices in place.
3. Make certain everyone is clear before operating machine.
4. Keep hands, feet, and clothing away from moving parts.
5. Shut off power to adjust, service, or clean.
6. Make sure machine is secured before operating.
7. When transporting, shut fuel valve lever off.
Pre-Operation Check List
1. Check all bearings for proper lubrication.
2. Check the tube for foreign material.
3. Check all belts for proper tension.
4. Start unit and check tender belt alignment while unit is empty.
BELT CARE ………
It is suggested that the unit be run every two to three days or more often if possible. This tends to keep
the tender belt alive and stops any forming of the belt to the curvature of the tube while the unit is not
in use.
NOTE: Belt may deteriorate if not in use and exposed to weather conditions for any prolonged period
of time.
Operation Sequence
1. Check drive belt for proper tension.
2. Make sure tender belt is properly tensioned.
3. Allow unit to run empty for a few minutes to flex tender belt.
4. Check tender belt for proper alignment.
5. Before shutting power off, be certain head and tail unit is empty.
STORAGE ………
Temporary Storage
1. Relieve tension from all belts; both v-belt and tender belt.
2. Store all belt equipment in a dry place. If equipment cannot be stored out of the weather,
cover engine and mechanical parts with waterproof material.
Prolonged Storage
1. Remove all belts and store in a cool, dark, dry place.
2. Wash belt thoroughly.
3. Wash tube both inside and out.
4. Lubricate all bearings.
5. Store in a dry shelter.
3

With transport lock in upper
hole on 54" trailer, unit is
over legal road height.
For optimal performance, use
lower hole to convey grain if
height allows.
Safety
Transport Lock - 160 Bu
4

With transport lock in upper
hole on 54" trailer, unit is
over legal road height.
For optimal performance, use
lower hole to convey grain if
height allows.
Safety
Transport Lock - 240 Bu
5

Safety Decals
REMEMBER: If Safety signs have been damaged, removed, become illegible or parts replaced without
decals, new decals must be applied. New decals are available from your authorized
distributor or factory. Individual decals shown below.
#05329800 #05303300
#05315700
#05325600 #05327200
#05328000 #05312400
6

Maintenance
Preventive maintenance is the key to the long life of any mechanical device.
Careful and systematic inspection of the Seed Tender will result in maximum, trouble-free service.
BELT REPLACEMENT ………
To replace the belt, cut it into and hand rotate the head roller until belt has been removed.
Install appropriate belt as outlined in assembly instructions. (See page 6.)
HEAD ASSEMBLY TAKE-UP ………
After extended use, the belt may stretch to the point that there is not sufficient take-up in
the head assembly to tighten it. Obtain additional take-up by cutting a 6" to 8" section
from the belt. A new splice lacing may be ordered from your CrustBuster/Speed King
distributor or from the factory.
PERIODIC CLEAN-OUT ………
Due to the characteristics of certain materials, residue sometimes collects between the
tender belt and the tube. Check the unit periodically for any material build up in this area.
If residue appears excessive, remove the tender belt and thoroughly wash the belt and
tube. Allow belt and tube to dry before reinstalling the belt.
When the Seed Tender is not being used, secure belt to the tube to prevent belt from
flopping in the wind, possibly breaking return idlers or ripping belt.
LUBRICATION ………
All bearings which are fitted with grease zerks should be lubricated at the conclusion of
each operating day. Before greasing the bearings, make certain the zerks are free of dirt,
otherwise this will be passed into the bearing race. If the unit will be out of service for a
period of time, purge the bearings.
BELT TRAINING PROCEDURE ………
A belt correctly installed and trained will run straight and true. The belt must run centered
on all terminal rollers, take-up rollers, and return idlers throughout the entire belt length.
Incorrect installation and training can result in severe edge damage, material spillage,
material leakage through the skirt rubber at the loading point, and excessive power
demands. Material spillage is the usual reason for belt carcass ruptures and pulley cover
gouging and stripping, while leakage at the skirt rubber results in excessive conveyor
cover wear under the skirts.
ALIGNMENT ………
All rotating parts -head roller, tail roller, and return idlers- must be at a 90 degree angle
to the direction of belt travel, must be level, and the midpoint of each centered on a line
when properly aligned.
Alignment is checked by running a tight wire from the center of the head roller to the
center of the tail roller.
Level all rotating parts. If a part is not level, the belt will run to the lower side.
BELT SPLICING ………
A belt must not run out at the splice area. Runout will occur if the belt is not cut square
or splice is not installed square.
7

Through the down periods, the belt can adhesively
stick to the bottom of the tube. To unstick the belt,
use a screwdriver or a rod to push the belt up off
the bottom of the feed tube using holes located on
the bottom of the tube before running the unit.
Failure to make sure the belt is free will result in
belt failure.
Operation
1. Prior to the start-up, check to see that belt is free from any objects that would bind or tear.
2. On starting for the first time, with no load on belt, apply power for a few seconds only to see that
the belt is well centered in the tube and on the return.
3. It should be noted at this time that too much tension on the belt will make adjustment or training
much more difficult, shorten the life of the belt, and waste power. The belt should be tensioned
tight enough so the drive roller does not slip.
BELT TRAINING ………
It is essential that the belt be properly trained at all times. For this reason, all rotating parts should
always be at right angles to the tender belt.
Slight adjustment of roller shafts may be required to keep belts centered on them i.e., if the belt runs
to one side of the roller - apply more tension to this side of the belt by advancing the roller shaft on this
side. This can be done on the head section as long as adjustment bolt does not vary more than 1/4".
If it does, then some adjustment will need to be done on the tail end.
If the belt tends to veer to one side of the return strand, the belt can be centered by "knocking" ahead
(in the direction of belt travel) the end of the return idler to which the belt runs. A belt correctly installed
will usually train well both empty and loaded, except as noted:
1. One or more rotating parts not in alignment.
2. Belt tensions in some part of system (usually at tail section) are below minimum recommended.
3. Belt not loaded centrally.
When a belt is initially started, it should be jogged around the system to determine if a major runout
occurs which could damage belt and belt edges. If runout occurs at some point of the system, the
reason is usually a return idler or roller out of alignment before the runout. Alignment should be
rechecked before restarting.
After the belt can be safely run without damage, final training should begin with the head roller. The
belt must enter the head roller in the center without movement from side to side. If the belt is not
centered on the tail pulley, the return strand of belt should be observed for any section which is not
centered on the return idlers. If the belt is not centered at some point, move return idlers starting before
this point to correct centering of belt. Movement of idler bracket should be gradual and only 1/16" to
1/8" remembering that the belt will move in the direction that it first contacts the idler. The same
corrective action should be taken at the tail roller.
After the belt is trained empty, the belt should be trained with a load. The take-up adjustments are
made to prevent belt slip and keep tensions at all points above minimums recommended when belt is
operating with a load.
If slip occurs under load, additional belt tension should be applied by adjusting the take-up only enough
to prevent slip from occurring under load, and when started with a load.
8

BELT TIGHTENING
INSTRUCTIONS
Belt should be tightened before you train
the belt. Tightening the belt is done on
the head roller by tightening the take up
bars evenly. Belt is tight when applying
25 lbs. of force, centered between the
return rollers, there is no more than 2
inches of deflection.
BELT ASSEMBLY INSTRUCTIONS
At the start point, see view of head and tail assembly. Drop belt
over the top of head roller and gravity feed belt down the tender
tube to the bottom. Guide the belt over the top of the tail roller.
Make sure rough side is UP and the smooth side is DOWN
against the inside of wall of the tube.
Route both ends around head and tail rollers and over all return
idlers mounted under the tube. Slide belt forward or back
through tube so the ends of the belt meet at a convenient
location between return idlers to facilitate joining.
Align and interlace belt and clipper lacings. Slip splice pin
(Plastic covered cable) through clipper lacings to secure.
Belt Assembly
FOR FERTILIZER USE ONLY
Apply rubber adhesive, from tube furnished, to both sides of clipper lacing. This is
not done at the factory before shipping. Smooth adhesive and allow to set in
accordance with package directions. This rubber adhesive secures splice pin in
place and seals, so fertilizer dust does not settle on back side of belt and cause
inside of tube to rust.
Tighten belt by turning adjustment bolts on head assembly in. Tighten evenly on
each side until belt is tight.
To train belt, see belt training instructions in this manual.
9

Seed Tender 160
Dimensions
10

Seed Tender 240
Dimensions
11

Seed Tender 160 (Prior 2021)
Tank - Electric
12

Seed Tender 160 (Prior 2021)
Tank - Electric
Item Qty Part No. Description
1 1 82313800 Tank w/Frame
2
3
4 6 331363 Nylock Nut ½"
5 1 82322900 Ladder 6'
6 4 01180900 HHCS ½" x 1 1/4"
7 4 00716100 Vinyl Cap
8 12 330159 Flat Washer ½"
9 1 570630 Plastic Wear Plate
10 1 82114000 Pivot Base
11 1 332569 Machine Bushing
1 7/8" x 1 1/4" x 10 ga
12 1 967638 Pivot Base Shaft
13 1 153478 Lock Bushing
14 4 149393 Bushing ½" x 3/8" x 5/16"
15 5 01017300 HHCS 3/8" x 1"
16 2 01158500 HHCS 3/8" x 1 1/4"
17 2 330035 Hex Nut 3/8"
18 1 17306200 Guard Bracket
19 1 01574300 Clip Nut 5/16" U-type
20 1 62382700 Chain Guard
21 1 01489400 Thumb Screw 5/16" x 3/4"
22 6 330837 Nylock Nut 3/8"
23 1 62759600 Head & Tail 15' Tube
w/Wind Guards
24 1 82099300 Tail Hopper
25 4 01144500 HHCS 5/16" x 3/4"
26 16 330852 Flat Washer 5/16"
27 16 330845 Lock Washer 5/16"
28 16 330811 Hex Nut 5/16"
Item Qty Part No. Description
29 2 262170 Window Back Plate
30 2 571315 Plastic Window
31 12 01057900 HHCS 1/4" x 3/4"
32 12 330522 Nylock Nut 1/4"
33 2 17960600 Handle
34 2 337352 Handle Nut ½"-13 x 4½"
35 1 17940800 Hopper Door Left
36 1 17941600 Hopper Door Right
37 1 17910100 Hopper Door Back Plate
38 1 17919200 Hopper Door Front Plate
39 12 01047000 Carriage Bolt 5/16" x 1"
40 2 17961400 Linkage Plate
41 2 17909300 Spout Back Plate
42 1 82314600 Spout
43 1 331884 HHCS 3/8" x 2½"
44 1 17287400 Turnbuckle Pin
45 1 06814800 Turnbuckle 1" x 8 3/4"
46 1 332288 Jam Nut 1"
47 1 82527300 Turnbuckle Bracket
48 1 605220 Bushing 1 1/4" x 1 x ½" HS
49 1 330407 Flat Washer 1"
50 1 330597 Nylock Nut 1"
51 1 01172600 HHCS 1" x 2½"
52
53 2 02016400 Flat Washer 1/4"
54 1 02393700 HHCS 1/4" x 2 1/4"
55 1 970137 Extension Ladder
56 1 609255 Clevis Pin ½" x 1 3/8"
57 2 01147800 HHCS ½" x 1½"
58 1 330928 Klik Pin 3/16"
03824000 Tarp 160 Seed Tender
13

Seed Tender 160
Tank - Electric
14

Seed Tender 160
Tank - Electric
#90976200
Item Qty Part No. Description
1 1 82313800 Tank w/Frame
2
3
4 6 331363 Nylock Nut ½"
5 1 82322900 Ladder 6'
6 4 01180900 HHCS ½" x 1 1/4"
7 4 00716100 Vinyl Cap
8 12 330159 Flat Washer ½"
9 1 570630 Plastic Wear Plate
10 1 82114000 Pivot Base
11 1 332569 Machine Bushing
1 7/8" x 1 1/4" x 10 ga
12 1 967638 Pivot Base Shaft
13 1 153478 Lock Bushing
14 4 149393 Bushing ½" x 3/8" x 5/16"
15 5 01017300 HHCS 3/8" x 1"
16 2 01158500 HHCS 3/8" x 1 1/4"
17 2 330035 Hex Nut 3/8"
18 1 17306200 Guard Bracket
19 1 01574300 Clip Nut 5/16" U-type
20 1 62382700 Chain Guard
21 1 01489400 Thumb Screw 5/16" x 3/4"
22 6 330837 Nylock Nut 3/8"
23 1 63439400 Head & Tail 15' Tube
w/Wind Guards
24 1 82099300 Tail Hopper
25 4 01144500 HHCS 5/16" x 3/4"
26 16 330852 Flat Washer 5/16"
27 16 330845 Lock Washer 5/16"
28 16 330811 Hex Nut 5/16"
Item Qty Part No. Description
29 2 262170 Window Back Plate
30 2 571315 Plastic Window
31 12 01057900 HHCS 1/4" x 3/4"
32 12 330522 Nylock Nut 1/4"
33 2 17960600 Handle
34 2 337352 Handle Nut ½"-13 x 4½"
35 1 17940800 Hopper Door Left
36 1 17941600 Hopper Door Right
37
38 1 17919200 Hopper Door Front Plate
39 12 01047000 Carriage Bolt 5/16" x 1"
40 2 17961400 Linkage Plate
41 2 17909300 Spout Back Plate
42 1 82314600 Spout
43 1 331884 HHCS 3/8" x 2½"
44 1 17287400 Turnbuckle Pin
45 1 06814800 Turnbuckle 1" x 8 3/4"
46 1 332288 Jam Nut 1"
47 1 82527300 Turnbuckle Bracket
48 1 605220 Bushing 1 1/4" x 1 x ½" HS
49 1 330407 Flat Washer 1"
50 1 330597 Nylock Nut 1"
51 1 01172600 HHCS 1" x 2½"
52
53 2 02016400 Flat Washer 1/4"
54 1 02393700 HHCS 1/4" x 2 1/4"
55 1 970137 Extension Ladder
56 1 609255 Clevis Pin ½" x 1 3/8"
57 2 01147800 HHCS ½" x 1½"
58 1 330928 Klik Pin 3/16"
03824000 Tarp 160 Seed Tender
15

Seed Tender 160 (Prior 2021)
Tank - Gas
16

Seed Tender 160 (Prior 2021)
Tank - Gas
Item Qty Part No. Description
1 1 82313800 Tank w/Frame
2
3
4 6 331363 Nylock Nut ½"
5 1 82322900 Ladder 6'
6 4 01180900 HHCS ½" x 1 1/4"
7 4 00716100 Vinyl Cap
8 12 330159 Flat Washer ½"
9 1 570630 Plastic Wear Plate
10 1 82114000 Pivot Base
11 1 332569 Machine Bushing
1 7/8" x 1 1/4" x 10 ga
12 1 967638 Pivot Base Shaft
13 1 153478 Lock Bushing
14 1 62605100 Belt Guard
15 2 01017300 HHCS 3/8" x 1"
16 1 330837 Nylock Nut 3/8"
17 1 334847 Wing Nut 3/8"
18 1 330043 Lock Washer 3/8"
19 2 01158500 HHCS 3/8" x 1 1/4"
20
21 1 01172600 HHCS 1" x 2½"
22 4 149393 Bushing ½" x 3/8" x 5/16"
23 1 63437800 Head & Tail 15' Tube
w/Wind Guards (Shown)
1 62894100 Telescoping Tube
24 1 82099300 Tail Hopper
25 4 01144500 HHCS 5/16" x 3/4"
26 22 330852 Flat Washer 5/16"
27 22 330845 Lock Washer 5/16"
28 22 330811 Hex Nut 5/16"
29 2 262170 Window Back Plate
30 2 571315 Plastic Window
31 12 01057900 HHCS 1/4" x 3/4"
32 13 330522 Nylock Nut 1/4"
33 2 17960600 Handle
Item Qty Part No. Description
34 2 337352 Handle Nut ½"-13 x 4½"
35 1 17940800 Hopper Door Left
36 1 17941600 Hopper Door Right
37 1 17910100 Hopper Door Back Plate
38 1 17919200 Hopper Door Front Plate
39 12 01047000 Carriage Bolt 5/16" x 1"
40 2 17961400 Linkage Plate
41 2 17909300 Spout Back Plate
42 1 82314600 Spout
43 1 331884 HHCS 3/8" x 2½"
44 1 17287400 Turnbuckle Pin
45 1 06814800 Turnbuckle 1" x 8 3/4"
46 1 332288 Jam Nut 1"
47 1 82527300 Turnbuckle Bracket
48 1 605220 Bushing 1 1/4" x 1 x ½" HS
49 1 330407 Flat Washer 1"
50 1 330597 Nylock Nut 1"
51 1 62772900 Engine Assembly
Electric Start
1 62936000 Engine Assembly
Units with remote
52 1 01429000 Battery Box Group 24
53 4 335448 HHCS 5/16 x 1½"
54 1 62787700 Power Lead Cable
55 1 62774500 Solenoid Ground Wire
56 1 62782800 Battery Cable Positive
57 2 01010800 HHCS 5/16" x 1"
58 1 03752300 V-Belt B-44
59 2 02016400 Flat Washer 1/4"
60 1 02393700 HHCS 1/4" x 2 1/4"
61 2 01145200 HHCS 3/8" x 3/4"
62 1 20670600 Battery Mount Plate
63 1 970137 Extension Ladder
64 1 609255 Clevis Pin ½" x 1 3/8"
65 2 01147800 HHCS ½" x 1½"
66 1 330928 Klik Pin 3/16"
03824000 Tarp 160 Seed Tender
03962800 Remote Receiver
03963600 Remote Transmitter
17