CrustBuster 1325 User manual

Grain Cart
1325
OWNER'S
MANUAL
#613521 (2013)

Table of Contents
Warranty Information . . . . . . . . . . . . . Below
Dealer Check List . . . . . . . . . . . . . . . . . . . . 1
Introduction ....................... 2-4
Safety ........................... 5-6
Electrical ...........................7
Dimensions .........................8
Auger .......................... 9-11
DriveSystem.................... 12-13
Hopper and Auger Saddle . . . . . . . . . . . . . 14
Frame and Axle . . . . . . . . . . . . . . . . . . 15-16
Hydraulics . . . . . . . . . . . . . . . . . . . . . . . . . 17
Extension . . . . . . . . . . . . . . . . . . . . . . . . . 18
Tank ............................. 19
1325 Grain Cart . . . . . . . . . . . . . . . . . . . . 20
Engineering Specifications . . . . . . . . . . . . 21
Warranty
CrustBuster/Speed King, Inc. of Dodge City, Kansas, warrants consumer products, so far as
the same is of our own manufacture, against defects in material and workmanship under
normal and reasonable use for a period of one (1) year after date of delivery to the original
purchaser. Our obligation under this warranty is limited, however, to furnishing a replacement
part for a defective part, or at our option to repair the defective parts without charge, either
method F.O.B. our works, provided the consumer gives CrustBuster/Speed King,Inc. written
notice within ten (10) days after said part appears to be defective and affords
CrustBuster/Speed King,Inc. an opportunity to inspect. Unless otherwise expressly agreed
to by CrustBuster/Speed King,Inc., the consumer shall bear the expense of installation.
CrustBuster/Speed King, Inc. will not be liable for consequential damages where the loss is
commercial, including but not limited to loss of profit, delays or expenses.
This warranty sets forth the extent of our liability. The foregoing is in lieu of all other
warranties, expressed or implied, including any warranties that extend beyond the description
of the product.

1
Dealer Preparation Check List
Complete the items below before delivering the cart.
~ Gearbox filled with oil
~ All fittings lubricated
~ All shields in place and in good condition
~ All fasteners torqued to specifications on chart (Page 21)
~ Tires inflated to proper pressure according to chart (Page 21)
~ Check jack stand for proper stability
~ All decals in place and readable
~ Operator’s manual has been delivered to owner and the owner has been
instructed on safe and proper use of the cart
Dealer’s Signature
Customer’s Signature
This check list is to remain in the owner’s manual
It is the responsibility of the dealer to complete the procedures listed above before the delivery of this
cart to the new owner.

2
To the Owner
This operator’s manual is to be kept with this cart regardless of ownership.
CAUTION: Some of the illustrations in this manual may show the shields
or covers removed for clarity. NEVER OPERATE GRAIN CART
without all shields and covers in place.
Be sure to read all instructions for adjusting and operation of the cart contained in this manual. Check
each item referred to and acquaint yourself with them.
After each season, thoroughly clean your cart and inspect it for worn or damaged parts. Leave the
clean-out door located at the bottom open. This allows water to drain.
Your dealer has original equipment parts for your grain cart. When you need parts, always specify the
model number and the serial number. Write these numbers in the spaces provided below. The serial
plate is on the front of the cart.
Model Number Serial Number
1325
Introduction
This manual provides the necessary instructions for using and maintaining your grain cart. In addition,
it contains information on service, warranty, parts ordering, and safety considerations when using the
grain cart.
Your grain cart represents the latest in farm equipment technology. It has been continually
redeveloped and improved over the last sixty years to better serve grain farmers all over the country.
It is designed to be used with all types of grains without any modification required on the cart.
Your grain cart is designed to be towed by a tractor. The size of the tractor required depends on the
capacity of the cart and the field conditions. The tractor must be equipped with a 1.75 -20 Tooth -
1000RPM PTO for the PTO model on your cart. The tractor also must have an adequate hydraulic
system. Two remote hydraulic connections are required for the PTO models and four remotes for the
hydraulic drive models at (2500 psi & 22 gpm).
Please take the time to read this manual, especially the section on safety. If after reading the manual
you have any questions that your dealer cannot answer, please feel free to contact:
CrustBuster/Speed King, Inc.
P.O. Box 1438
Dodge City, Kansas 67801
Phone: [phone]

3
Initial Use
A careful operator is the best insurance against an accident!
CAUTION: Misuse or modification of this machine can cause
C
CC
C Mechanical breakdown
C
CC
C Personal injury or death
Before using this equipment for the first time, make sure you thoroughly
understand all of the operating instructions and have completely read this
manual.
All carts are shipped field ready; however, before initial use the following items should be checked:
C
CC
C All wheel lug nuts should be torqued to 450 ft-lbs of torque prior to initial use and should be
checked periodically.
C
CC
C Tires should be inflated to 58 psi.
C
CC
C Any retaining straps should be removed from the top auger.
C
CC
C Close dump door on bottom auger tube. (Leave this door open when not in use to allow for
water drainage.)
C
CC
C Make sure sufficient counter weights are used on tractor front end.
C
CC
C Move tractor draw bar to shortest position.
C
CC
C The hitch used on the 1325 cart requires a clevis type drawbar. If your tractor is not equipped
with such, please contact your dealer.
C
CC
C Connect hydraulic hoses and PTO shaft. Make sure the PTO shaft can telescope both inward
and outward at least 3".
C
CC
C Test grain door inside cart to ensure smooth operation and proper functioning of indicator.
C
CC
C Look into cart and make sure that the grain door hoses have not been damaged in shipment
and that they are not leaking.
CAUTION: Before testing the auger make sure no one is near the auger
assembly.
C
CC
C Fold the top auger to full upright position and engage the auger drive, slowly turning the auger.
If auger turns freely, then slowly increase the RPM to proper operating speed. Disengage the
auger drive, stopping rotation of the auger. Then slowly return the auger to the transport
position. If the auger seems to fold too fast, the flow control valve must be adjusted to match
your tractor’s hydraulic system (see details in auger section).