CTC Union IGS-800C-8PH User manual

1
Quick Installation Guide
[email protected]
IGS-800C-8PH
IGS-800C-8PHE
8 x GbE RJ-45 with 8 x PoE (240W, 48VDC) Compact-Sized
Switch (Hardened)

1
Version 1.0 March, 2020
2020 CTC Union Technologies Co., LTD.
All trademarks are the property of their respective owners.
Technical information in this document is subject to change without notice.
CTC Union Technologies Co.,Ltd.
Far Eastern Vienna Technology Center
(Neihu Technology Park)
8F, No. 60 Zhouzi St.,
Neihu, Taipei 114, Taiwan
T [phone]
F [phone]
E[email protected]m
Hwww.ctcu.com

2
LEGAL
The information in this publication has been carefully checked and is believed to be entirely accurate at
the time of publication. CTC Union Technologies assumes no responsibility, however, for possible errors
or omissions, or for any consequences resulting from the use of the information contained herein. CTC
Union Technologies reserves the right to make changes in its products or product specifications with the
intent to improve function or design at any time and without notice and is not required to update this
documentation to reflect such changes.
CTC Union Technologies makes no warranty, representation, or guarantee regarding the suitability of its
products for any particular purpose, nor does CTC Union assume any liability arising out of the
application or use of any product and specifically disclaims any and all liability, including without
limitation any consequential or incidental damages.
CTC Union products are not designed, intended, or authorized for use in systems or applications
intended to support or sustain life, or for any other application in which the failure of the product could
create a situation where personal injury or death may occur. Should the Buyer purchase or use a CTC
Union product for any such unintended or unauthorized application, the Buyer shall indemnify and hold
CTC Union Technologies and its officers, employees, subsidiaries, affiliates, and distributors harmless
against all claims, costs, damages, expenses, and reasonable attorney fees arising out of, either directly
or indirectly, any claim of personal injury or death that may be associated with such unintended or
unauthorized use, even if such claim alleges that CTC Union Technologies was negligent regarding the
design or manufacture of said product.
WARNING:
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with
the instruction manual may cause harmful interference in which case the user will be required to correct
the interference at his own expense. NOTICE: (1) The changes or modifications not expressively
approved by the party responsible for compliance could void the user's authority to operate the
equipment. (2) Shielded interface cables and AC power cord, if any, must be used in order to comply
with the emission limits.
This is a Class A product. In a domestic environment this product may cause radio interference in which
case the user may be required to take adequate measures.

4
Table of Contents
Introduction..................................................................................5
Package List.................................................................................5
Features........................................................................................5
Specifications...............................................................................6
ETHERNET INTERFACE............................................................................................ 6
POWER OVER ETHERNET ........................................................................................ 6
POWER ............................................................................................................. 6
MECHANICAL...................................................................................................... 7
ENVIRONMENTAL................................................................................................. 7
CERTIFICATIONS .................................................................................................. 7
MTBF (MIL-HDBK-217) .................................................................................... 7
Panels ...........................................................................................8
Connections .................................................................................9
LAN PORTS ....................................................................................................... 9
POEPORTS ........................................................................................................ 9
RJ-45 ETHERNET PORT PINOUTS ............................................................................. 9
Recommended Power & Ground Wiring Scheme....................10
DC POWER CONNECTION .....................................................................................10
EARTH GROUNDING CONNECTION...........................................................................11
Installation..................................................................................12
LED Indicators............................................................................13

5
Introduction
IGS-800C-8PH(E) are unmanaged industrial grade Gigabit PoE
(Power over Ethernet) switches that provide stable and reliable Ethernet
transmission. Housed in rugged DIN rail or wall mountable enclosures,
these switches are designed for harsh environments, such as industrial
networking and intelligent transportation systems (ITS) and are also
suitable for many military and utility market applications where
environmental conditions exceed commercial product specifications.
Standard operating temperature range models (-10°C to 60°C) and wide
operating temperature range models (-40°C to 70°C) fulfill the special
needs of industrial automation applications.
Package List
One IGS-800C-8PH(E) device
DIN rail with screws
Terminal block
Features
IP30 rugged metal housing
Wide temperature range -40°C~70°C (IGS-800C-8PHE)
Support Ethernet jumbo frames
Support flow control
Support DIN rail and wall mounting installation

6
Specifications
Ethernet Interface
Standards: IEEE802.3, 802.3u, 802.3ab, 802.3x, 802.3af, 802.3at
Connector Type: RJ-45 (shielded)
Number of Connector: 8 ports
Speed: 10/100/1000Base-T (Auto)
Auto MDI/MDI-X
Duplex: Full/Half (Auto-negotiation per IEEE802.3u)
Support IEEE802.3x Flow Control
Store & Forward Switch
Switching Fabric: 16Gbps (Full wire-speed)
MAC Table: 4K
Jumbo Frame: 9K Bytes
Power over Ethernet
8 PoE Enabled Ports
Total PoE Output Power Budget (Max.): 240W (30W Per Port)
Support IEEE802.3af 15.4W PoE Per Port
Support IEEE802.3at 30W PoE+ Per Port
Positive (V+) Pins 1,2; Negative (V-) Pins 3,6; Data Pins 1, 2, 3, 6, 4, 5, 7,
8
Power
Support Redundant 48VDC (44VDC~57VDC) Dual Power Inputs
For IEEE802.3at PoE+ applications, 50~57VDC power input is
recommended.
Connector: Removable Terminal Block
Support Power Input Reverse Polarity Protection
Support Overload Current Protection
Consumption:
Input
Voltage
Total Power
Consumption
Device Power
Consumption
PoE
Budget
50VDC
247.6W
6.8W
240W

7
Mechanical
Housing: Rugged Metal, IP30 Protection
Fanless Design
Dimensions: 100 mm (D) x 42 mm (W) x 115 mm (H)
Installation Method: DIN Rail & Wall Mounting (Optional accessory)
Weight: 950g
Environmental
Operating Temperature: -10°C~60°C (IGS-800C-8PH); -40°C~70°C (IGS-
800-8PHE)
Humidity: 5%~95% (Non-condensing)
Certifications
EMC: CE (EN55024, EN55032)
EMI (Electromagnetic Interference): FCC Part 15 Subpart B Class A, CE
EN55022 Class A
Railway Traffic: EN50121-4
Immunity for Heavy Industrial Environment: EN61000-6-2
Emission for Heavy Industrial Environment: EN61000-6-4
EMS (Electromagnetic Susceptibility) Protection Level:
EN61000-4-2 (ESD) Level 3, Criteria B
EN61000-4-3 (RS) Level 3, Criteria A
EN61000-4-4 (Burst) Level 3, Criteria A
EN61000-4-5 (Surge) Level 3, Criteria B
EN61000-4-6 (CS) Level 3, Criteria A
EN61000-4-8 (PFMF, Magnetic Field) Field Strength: 300A/m,
Criteria A
Surge Protection: 4KV for PoE and UTP Ports
Safety: EN62368-1 (Pending)
Shock: IEC 60068-2-27
Freefall: IEC 60068-2-32
Vibration: IEC 60068-2-6
MTBF (MIL-HDBK-217)
1,494,598 Hours

8
Panels
Index
No.
Description
1
RJ-45 Ethernet
Ports (1~8)
2
Power LED
Indicators
3
PoE LED Indicators
4
10/100/1000
Link/Act LED
Indicators
5
Power Terminal
Block
6
Grounding Screw
5
6
2
3
4
1
1
Figure 1. Front Panel
6
5
Figure 2. Top Panel

9
Connections
LAN Ports
IGS-800C-8PH(E) models have 8 LAN ports (labeled 1~8) on the front
panel. The LAN ports that utilize shielded RJ-45 connectors support
10/100/1000M. Port speed and link activity can be shown in real-time on
the individual LED indicator.
PoE Ports
8 LAN ports (labeled 1~8) all support PoE (Power over Ethernet) per
IEEE802.3af (15.4W) or IEEE802.3at (30W) for connection to standard
PoE PD (Power Devices) such as IP Cameras, Access Points, IP Phones,
Digital Signage, etc. PoE not only eliminates the need to run separate
power to these devices, but also simplifies deployment and reduces
expenses. The LAN ports may also connect to any non-PoE device for
normal Ethernet transmission without any damage to the non-PoE
device or to this device.
NOTE: IGS-800C-8PH(E) is a PSE device that can connect to PDs (Powered Devices)
or non-PoE devices. However, it is NOT recommended to connect IGS-800C-8PH(E)
to another PSE device. By doing so, it may have potential risks to cause device
damages.
RJ-45 Ethernet Port Pinouts
Pin No.
RJ-45 Ethernet
PoE Output
100Base-TX
1000Base-T
1
RX+
TRD 0+
V+
2
RX-
TRD 0-
V+
3
TX+
TRD 1+
V-
4
-
TRD 2+
5
-
TRD 2-
6
TX-
TRD 1-
V-
7
-
TRD 3+
8
-
TRD 3-
Figure 3. RJ-45
Ethernet Port
Pinouts
Figure 4. RJ-45 Ethernet &
PoE Pin Assignments

10
+ -+ -
Recommended Power & Ground Wiring Scheme
DC Power Connection
A removable terminal block on the top panel provides power source
connections. Power can be provided through the dual inputs from
separate sources (PWR1 & PWR2). One power supply is enough to
power up the device. If two power supplies are used, the device
provides power redundancy function. See the figure provided below for
recommended DC power wiring scheme.
Figure 5. DC Power Connection

11
Earth Grounding Connection
An earth grounding connection hole is provided on the top panel
with an earth ground sign next to it. Grounding the device can help to
release leakage of electricity to the earth safely so as to reduce injuries
from electromagnetic interference (EMI).
Prior to connecting to the power, it is important to connect the
ground wire to the earth. Follow steps below to install ground wire:
Step 1. Make sure you have the grounding screw and grounding cable
at hand.
Step 2. Unfasten the ground screw on the front panel.
Step 3. Attach the grounding screw to the ring terminal of the
grounding cable. Make sure that the grounding cable is long enough to
reach the earth.
Step 4. Use a screwdriver (or other tools) to fasten the grounding
screw on the earth ground hole securely.
ATTENTION: It is important to mount this product on the well-grounded surface
before using it so as to reduce unexpected noises or injuries.
Figure 6. Earth Grounding Connection
Ring-type
terminal
Fork-type
terminal

12
Installation
The switch can be mounted on the wall or installed in DIN rail
depending on your installation needs. When installing the wall-mounting
bracket (optional accessory) and DIN rail bracket, be sure to correctly
align the orientation pin.
Figure 7. DIN Rail Figure 8. Wall Mount
The switch with DIN Rail bracket has a steel spring in the upper rail of
the bracket. This spring is compressed for mounting and un-mounting by
applying downward force.
Figure 9. Mounting
Figure 10.Un-Mounting

13
LED Indicators
LED
Color
Status
Definition
PWR1
PWR2
Green
On
Power is connected and active at
the PWR1/PWR2 input terminal
connection.
Off
PWR1/PWR2 is not connected.
LINK/ACT
Green
On
Lit when the LAN connected
speed is 10/100M.
Blinking
Blinking when there is Ethernet
traffic.
Amber
On
Lit when the LAN connected
speed is 1000M.
Blinking
Blinking when there is Ethernet
traffic.
PoE
Green
On
The respective LAN port has
successfully negotiated PoE and
is supplying output power to the
remote connected PD.
Off
PD is not connected or output
power is not provided.

14
Version
Date
Description
1.0
2020/3/18
Preliminary version.
-Revise weight info.