Cybernet H6 i-One Series User manual

LCD-PC
i-One Series H6/H7
User Guide

i
FCC-B Radio Frequency Interference Statement
This equipment has been tested and found to comply with
the limits for a class B digital device, pursuant to part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the
measures listed below.
•Reorient or relocate the receiving antenna.
•Increase the distance between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
•Consult the dealer or an experienced radio/television technician for help.
Notice 1 The changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the
equipment.
Notice 2 Shielded interface cables and A.C. power cord, if any, must be used in order
to comply with the emission limits.
Trademarks
All trademarks are the properties of their respective owners.
Intel® is a registered trademarks of Intel Corporation.
Windows® 7/Vista/XP/NT/2000/98/95 are registered trademarks of Microsoft Corporation.
Award® is a registered trademark of Phoenix Technologies Ltd.
AMI® is a registered trademark of American Megatrends Inc

ii
Safety Instructions
1. Always read the safety instructions carefully.
2. Keep this equipment away from humidity.
3. Lay this equipment on a reliable flat surface before setting it up.
4. The openings on the enclosure are for air convection hence protect the
equipment from overheating. DO NOT COVER THE OPENINGS.
5. Confirm the voltage of the power source and adjust accordingly to 110/220V
before connecting the equipment to the power inlet.
6. Place the power cord in such a way that it cannot be stepped on. Do not
place anything over the power cord.
7. Always unplug the Power Cord before inserting any add-on card or module.
8. All cautions and warnings on the equipment should be noted.
9. Never pour any liquid into the opening. This will cause damage and/or electrical
shock.
10. Do not disable the protective grounding pin from the plug. The equipment must be
connected to a grounded main socket/outlet.
11. The Optical Storage devices are classified as Class 1 Laser products. Use of
controls or adjustments or performance of procedures other than those specified is
prohibited.
12. Do not touch the Laser lens inside the optical storage drive.
13. When installing the coaxial cable to the TV Tuner, it is necessary to ensure that the
metal shield is reliably connected to a protective earthing system of the building.
Cable distribution systems should be grounded (earthed) in accordance with
ANSI/NF PA 70, the National Electrical Code (NEC ), in particular, Section 820.93,
Grounding of Outer Conductive Shield of a Coaxial Cable.
14. If any of the following situations arise, have the equipment checked by authorized
service personnel:
•The power cord or plug is damaged.
•Liquid has penetrated into the equipment.
•The equipment has been exposed to moisture.
•The equipment has not worked well or you cannot get it working according to
the User's Guide.
•The equipment has been dropped and damaged.
•The equipment has obvious signs of breakage.
15. Do not attempt to remove or upgrade any component by yourself, any installation or
modification should be conducted by service personnel.
DO NOT LEAVE THIS EQUIPMENT IN AN UNCONDITIONED ENVIRONMENT WITH A
STORAGE TEMPERATURE ABOVE 50° C (122°F). IT MAY DAMAGE THE
EQUIPMENT.
CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the
same or equivalent type recommended by the manufacturer.

iii
WEEE Statement
(Waste Electrical and Electronic Equipment)
The WEEE directive places an obligation on EU-based manufacturers, distributors,
retailers and importers to take-back electronics products at the end of their useful life. A
sister Directive, ROHS (Restriction of Hazardous Substances) compliments the WEEE
Directive by banning the presence of specific hazardous substances in the products at the
design phase. The WEEE Directive covers products imported into the EU as of August 13,
2005. EU-based manufacturers, distributors, retailers and importers are obliged to finance
the costs of recovery from municipal collection points, reuse, and recycling of specified
percentages per the WEEE requirements.
Instructions for disposal of WEEE by Users in the European Union
The symbol shown below is on the product or on its packaging, which indicates that this
product must not be disposed of with other waste. Instead, it is the user’s responsibility to
dispose of their waste equipment by handing it over to a designated collection point for the
recycling of waste electrical and electronic equipment. The separate collection and
recycling of your waste equipment at the time of disposal will help to conserve natural
resources and ensure that it is recycled in a manner that protects human health and the
environment. For more information about where you can drop off your waste equipment
for recycling, please contact your local city office, your household waste disposal service
or where you purchased the product.

iv
TABLE OF CONTENTS
FCC-B Radio Frequency Interference Statement ........................................................i
Trademarks.....................................................................................................................i
Safety Instructions........................................................................................................ii
WEEE Statement ..........................................................................................................iii
Introduction ...................................................................................................................1
LCD-PC i-One Series H6/H7 Specifications ................................................................1
Processor Support ..................................................................................................................1
Motherboard Core Logic........................................................................................................ 1
Memory Support......................................................................................................................1
Networking...............................................................................................................................1
Audio.........................................................................................................................................1
Hard Disk Drive........................................................................................................................1
Mounting...................................................................................................................................2
LCD Panel.................................................................................................................................2
Expansion Slots.......................................................................................................................2
Front Lower Right Bezel .........................................................................................................2
Right Side Bezel.......................................................................................................................2
Left Side Bezel.........................................................................................................................2
Bottom I/O Panel.....................................................................................................................2
Power Supply...........................................................................................................................2
Dimensions ..............................................................................................................................2
LCD-PC i-One Series H6/H7 Overview.........................................................................3
On Screen Display Buttons ....................................................................................................6
On Screen Display Usage.......................................................................................................7 
On Screen Display Icons.........................................................................................................7
System Assembly........................................................................................................10
Necessary Tools................................................................................................................... 10
Orientation of Key Parts........................................................................................................11
iOne-H6/H7 Disassembly ......................................................................................................12
Installing the CPU..................................................................................................................14
Installing the CPU Heat Sink.................................................................................................15
Installing the Memory Module DDR3 SO-DIMM ..................................................................16
Installing the Hard Disk Drive...............................................................................................17

v
Installing the Optical Disk Drive...........................................................................................18
Installing the Mini-PCIe Card (Optional)..............................................................................20
Installing the Cover ...............................................................................................................21
Cybernet Recycling SOP…………………………………………………………………………….23
Figures
Figure 1: Front View with Optional Webcam ..............................................................3
Figure 2: Left side view with Optical Drive .................................................................4
Figure 3: Power Button and USB Ports.......................................................................5
Figure 4: Touch Panel...................................................................................................5
Figure 5: IrDA Receiver for TV Tuner ..........................................................................5
Figure 6: On Screen Display Buttons…………………………………..…….………….....6
Figure 7: On Screen Display Icons..............................................................................7
Figure 8: Back view.......................................................................................................8
Figure 9: Bottom Panel I/O Ports.................................................................................8
Figure 10: CPU Heat Sink Ventilation Fan...................................................................9
Figure 11: System Ventilation, System Ventilation and Stand..................................9
Figure 12: System Fans, CPU Heat Sink Fan and Ventilation .................................11
Figure 13: Open system ............................................................................................13
Figure 14: Open system with GPU ...........................................................................13

Cybernet iOne-H6/H7
Page 1
Introduction
Congratulations for purchasing the iOne-H6/H7. The LCD-PC i-One Series is your best
Slim LCD PC choice. With the fantastic appearance and small form factor, it can easily
be set anywhere. The feature packed platform also gives you an exciting PC experience.
LCD-PC i-One Series H6/H7 Specifications
Processor Support
2nd generation Intel® Core™ i3 i5 and Core™ i7 in the 1155 package up to 65W.
Motherboard Core Logic
Intel® H61 Express chipset (Sandy Bridge)/Intel® H77 Express chipset (Ivy Bridge)
Memory Support
DDR3 1066/1333 MHz SO-DIMM SDRAM (Un-buffered Non-ECC)
2DDR3 1333 MHz SO-DIMM slots (8GB Max)
Video & Graphics for H6/H7
Intel® integrated H61/H77 Chipset with Intel® HD Graphics
Intel GMA HD/Intel Clear Video HD Technology
Built-in support for 1080p HD video playback, HDMI 1.4 & Blu-ray 3D support
Supports Microsoft®DirectX 10.1/DirectX 11, Shader Model 4.0 and OpenGL 3.0.
DVMT allocated as needed from 128MB to 1.70GB
Maximum display resolution 2560 x 1600.
Video & Graphics for H6G/H7G
Onboard NVIDIA GeForce GT 540M(630M) GPU
1.0GB sDDR3 128-bit RAM
1080p HD video playback, HDMI 1.4 & Blu-ray 3D support.
Supports Microsoft® DirectX 11, Shader Model 5.0 and OpenGL 4.1
Maximum display resolution 2560 x 1600.
Networking
Supports 2 PCI Express LAN 10/100/1000 Fast Ethernet by Realtek RTL8111E
Audio
2 internal speakers with 78dB+/-3dB @ 2.5W
HD Audio Codec Realtek® ALC892 Flexible 10-channel audio with jack sensing,
Compliant with Azalia 1.0 Spec
Hard Disk Drive
One 2.5” SATA / SATA II Hard Disk Drive - Any Capacity

Cybernet iOne-H6/H7
Page 2
Wall Mount
Support 75x75 / 100x100 VESA mounting hole.
Swivel Stand
System Base enables left/right rotation up to 60 degrees. tilt from -5 to 60 degrees.
LCD Panel
20" TFT LCD screen 16:9 format display
Expansion Slots
2 mini-PCIe (One full size and one half size)
Front Lower Right Bezel
On Screen Display Buttons
Volume Adjust
Brightness Adjust
Contrast Adjust
Mute/Exit
Menu/Enter
Right Side Bezel
1 power button, 2 USB 2.0 ports (for mouse and keyboard)
Left Side Bezel
1 optical disk drive – 2.5” slim
Bottom I/O Panel
1 DC/IN port, 1 Serial port
1 DVI-I port, 1 HDMI port
2 LAN RJ-45, 2 USB3.0 ports, 2 USB2.0 ports
3 Audio jacks – Line in, Line Out and Mic in
4 TV Tuner ports - - Optional with TV Tuner (COAX Cable In, RCA Composite Video In,
Audio Left & Audio Right), 1 CMOS clear button, 1 Reset button
Power Supply
180 Watt Power Adapter, AC Input: 100~240V AC, 2.5A, 50-60Hz
DC Output: 19V, 9.5A only
Dimensions
491mm (H) x 258.5mm (W) x 460.5 mm (D) (with stand)

Cybernet iOne-H6/H7
Page 3
LCD-PC i-One Series H6/H7 Overview
Figure 1: Front View with Optional Webcam

Cybernet iOne-H6/H7
Page 4
Figure 2: Left side view with Optical Drive

Cybernet iOne-H6/H7
Page 5
Figure 3: Power Button and USB Ports
Figure 4: Touch Panel
Figure 5: IrDA Receiver for TV Tuner

Cybernet iOne-H6/H7
Page 6
On Screen Display Buttons
Figure 6: On Screen Display Buttons
There are six buttons on the lower bezel of the screen. From left to right they are:
Volume – Volume + Brightness – Contrast + Mute/Exit Menu/Enter
Volume - Press to decrease volume.
Volume + Press to increase volume.
Brightness- Press first to select Brightness adjustment. Press again to decrease
brightness. Press Contrast + to increase brightness. Brightness can also
be adjusted in Menu Mode.
Contrast + Press first to select Contrast adjustment. Press again to increase contrast.
Press Brightness – to decrease contrast. Contrast can also be adjusted in
Menu Mode.
Mute/Exit Press once to toggle Mute On or Off.
Also functions as Exit button in the Menu Mode.
Menu/Enter Press once to get to On-Screen display Mode to allow various adjustments
as listed below.
Also functions as the Enter or Select button in Menu Mode.

Cybernet iOne-H6/H7
Page 7
On Screen Display Usage
Figure 7: On Screen Display Icons
When the Menu button is pressed, the on-screen display appears as pictured above.
When in Menu Mode you can move to the various icons with the – (left) or + (right)
button. When you are at the icon you wish to adjust, press Menu again (Enter) to change
the color of the icon and then toggle your desired adjustment by again pressing either –
(left) or + (right). The screen will exit automatically in a matter of seconds if no selection
is made.
Contrast Select to toggle greater or lesser contrast.
Brightness
Select to toggle greater or lesser brightness.
Select to adjust the appearance of the screen to “Cool”.
Select to adjust the appearance of the screen to “Warm”.
OSD Firmware EEPROM version information
Select to reset all LCD Display settings
Select to toggle through the languages offered.
Screen Horizontal and Vertical adjustment, OSD display time set up
Screen mode selection for 16:9 or 4:3

Cybernet iOne-H6/H7
Page 8
Figure 8: Back view
Figure 9: Bottom Panel I/O Ports

Cybernet iOne-H6/H7
Page 9
Figure 10: CPU Heat Sink Ventilation Fan
Figure 11: System Ventilation Fan, System Ventilation and Stand

Cybernet i-One H6/H7 System Assembly
Page 10
System Assembly
This chapter provides system assembly information and procedures. While performing
any installation, use a grounded wrist strap before handling computer components and
carefully follow all installation procedures. Static electricity may damage the
components.
This chapter will include instructions for how to install CPU, heat sink, memory modules,
hard disk drive (HDD), optical disk drive (ODD), mini-PCIE card and IrDA module.
Necessary Tools
A Phillips screwdriver can be used to do most of the installation. One with
a magnetic head is recommended. Applied maximum torque is 5kg.
Pliers can be used as an auxiliary tool to connect some connectors or
cables.
Forceps/tweezers can be used to pick up tiny screws or set up the
jumpers.
Rubber gloves can prevent injury from static charge.
Electric screwdriver can be used to secure all screws more quickly.

Cybernet i-One H6/H7 System Assembly
Page 11
Orientation of Key Parts
Figure 12: System Fans, CPU Heat Sink Fan and Ventilation

Cybernet i-One H6/H7 System Assembly
Page 12
i-One H6/H7 Disassembly
ORIENTATION: Presumes the top of the iOne is away from you and the bottom or I/O
controller board is nearest you.
1. Place the iOne face down on a padded surface.
2. Remove the four screws from the base plate that attaches the stand to the LCD
supporting the base while removing the last screw.
3. Remove the ten back bezel screws.
4. Carefully remove the back bezel and set aside.
5. Then remove the metal EMI shield by first removing the I/O cover by removing the
three screws on the bottom and two screws on the face. Lift the plate out and up
and set aside.
6. Remove the remaining eleven screws around the metal shield covering the
motherboard.
7. First lift the metal shield and slide it to the right clearing the optical drive door (at
the top right) then disconnect the system fan cable connector from the
motherboard at System FAN1 connector at bottom left corner next to the com port.
And System Fan2 connector at bottom right corner next to the LVDS connector.

Cybernet i-One H6/H7 System Assembly
Page 13
Figure 13: Open system without GPU
Figure 14: Open system with GPU