Cybernet iOne-H19 Series User manual

LCD-PC iOne-H19 Series
User Guide

i
FCC-B Radio Frequency Interference Statement
This equipment has been tested and found to comply
with the limits for a class B digital device, pursuant to part 15 of the FCC rules. These
limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the measures listed below.
•Reorient or relocate the receiving antenna.
•Increase the distance between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
•Consult the dealer or an experienced radio/television technician for help.
Notice 1 The changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the
equipment.
Notice 2 Shielded interface cables and A.C. power cord, if any, must be used in
order to comply with the emission limits.
Trademarks
All trademarks are the properties of their respective owners.
Intel® is a registered trademarks of Intel Corporation.
PS/2 and OS®/2 are registered trademarks of International Business Machines
Corporation.
Windows® 7/Vista/XP/NT/2000/98/95 are registered trademarks of Microsoft
Corporation.
Netware® is a registered trademark of Novell, Inc.
Award® is a registered trademark of Phoenix Technologies Ltd.
AMI® is a registered trademark of American Megatrends Inc

ii
Safety Instructions
1. Always read the safety instructions carefully.
2. Keep this equipment away from humidity.
3. Lay this equipment on a reliable flat surface before setting it up.
4. The openings on the enclosure are for air convection hence protect the
equipment from overheating. DO NOT COVER THE OPENINGS.
5. Confirm the voltage of the power source and adjust accordingly to 110/220V
before connecting the equipment to the power inlet.
6. Place the power cord in such a way that it cannot be stepped on. Do not
place anything over the power cord.
7. Always unplug the Power Cord before inserting any add-on card or module.
8. All cautions and warnings on the equipment should be noted.
9. Never pour any liquid into the opening. This will cause damage and/or electrical
shock.
10. Do not disable the protective grounding pin from the plug. The equipment must
be connected to a grounded main socket/outlet.
11. The Optical Storage devices are classified as Class 1 Laser products. Use of
controls or adjustments or performance of procedures other than those specified
is prohibited.
12. Do not touch the Laser lens inside the optical storage drive.
13. When installing the coaxial cable to the TV Tuner, it is necessary to ensure that
the metal shield is reliably connected to a protective earthing system of the
building. Cable distribution systems should be grounded (earthed) in accordance
with ANSI/NF PA 70, the National Electrical Code (NEC ), in particular, Section
820.93, Grounding of Outer Conductive Shield of a Coaxial Cable.
14. If any of the following situations arise, have the equipment checked by
authorized service personnel:
•The power cord or plug is damaged.
•Liquid has penetrated into the equipment.
•The equipment has been exposed to moisture.
•The equipment has not worked well or you cannot get it working according to
the User's Guide.
•The equipment has been dropped and damaged.
•The equipment has obvious signs of breakage.
15. Do not attempt to remove or upgrade any components by yourself, any
installation or modification should be conducted by service personnel.
DO NOT LEAVE THIS EQUIPMENT IN AN UNCONDITIONED ENVIRONMENT WITH
A STORAGE TEMPERATURE ABOVE 50° C (122°F). IT MAY DAMAGE THE
EQUIPMENT.
CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the
same or equivalent type recommended by the manufacturer.

iii
WEEE Statement
(Waste Electrical and Electronic Equipment)
The WEEE directive places an obligation on EU-based manufacturers, distributors,
retailers and importers to take-back electronics products at the end of their useful life.
A sister Directive, ROHS (Restriction of Hazardous Substances) compliments the
WEEE Directive by banning the presence of specific hazardous substances in the
products at the design phase. The WEEE Directive covers products imported into the
EU as of August 13, 2005. EU-based manufacturers, distributors, retailers and
importers are obliged to finance the costs of recovery from municipal collection points,
reuse, and recycling of specified percentages per the WEEE requirements.
Instructions for disposal of WEEE by Users in the European Union
The symbol shown below is on the product or on its packaging, which indicates that
this product must not be disposed of with other waste. Instead, it is the user’s
responsibility to dispose of their waste equipment by handing it over to a designated
collection point for the recycling of waste electrical and electronic equipment. The
separate collection and recycling of your waste equipment at the time of disposal will
help to conserve natural resources and ensure that it is recycled in a manner that
protects human health and the environment. For more information about where you
can drop off your waste equipment for recycling, please contact your local city office,
your household waste disposal service or where you purchased the product.

iv
TABLE OF CONTENTS
FCC-B Radio Frequency Interference Statement ........................................................i
Trademarks.....................................................................................................................i
Safety Instructions........................................................................................................ii
WEEE Statement ..........................................................................................................iii
Introduction ...................................................................................................................1
iOne-H19 Series Specifications ...................................................................................1
Processor Support ..................................................................................................................1
Chipset......................................................................................................................................1
Memory Support......................................................................................................................1
Networking...............................................................................................................................1
Audio.........................................................................................................................................1
Hard Disk Drive........................................................................................................................2
Mounting...................................................................................................................................2
Swivel Stand.............................................................................................................................2
LCD Panel.................................................................................................................................2
Expansion Slots.......................................................................................................................2
Front Lower Right Bezel .........................................................................................................2
Right Side Bezel.......................................................................................................................2
Left Side Bezel.........................................................................................................................2
Bottom I/O Panel.....................................................................................................................2
Power Supply...........................................................................................................................2
Dimensions ..............................................................................................................................2
Power Management.......................................................................................................3
Waking the System Up............................................................................................................5
Energy Saving Tips .................................................................................................................5
iOne-H19 Series Overview............................................................................................6
On Screen Display Buttons ....................................................................................................9
On Screen Display Usage.....................................................................................................10
On Screen Display Icons.........................................................................................................7
System Assembly........................................................................................................13
Necessary Tools....................................................................................................................13
Orientation of Key Parts........................................................................................................14
iOne-H19 Disassembly..........................................................................................................15

v
Installing the CPU..................................................................................................................18
Installing the CPU Heat Sink.................................................................................................19
Installing the Memory Module DDR3 SO-DIMM ..................................................................20
Installing the Hard Disk Drive...............................................................................................21
Installing the Optical Disk Drive...........................................................................................22
Installing the Cover ...............................................................................................................25
Cybernet E-Recycling SOP…………………………………………………………………………………27
Figures
Figure 1: Front View with Optional Webcam ..............................................................6
Figure 2: Left side view with Optical Drive .................................................................7
Figure 3: Power Button and USB Ports.......................................................................8
Figure 4: Touch Panel...................................................................................................8
Figure 5: IrDA Receiver for TV Tuner ..........................................................................8
Figure 6: Back view.....................................................................................................11
Figure 7: Bottom Panel I/O Ports...............................................................................11
Figure 8: System Ventilation Fan...............................................................................12
Figure 9: Heat Sink Ventilation, System Ventilation and Stand ..............................12
Figure 10:.....................................................................................................................14
System Fan and Ventilation.............................................................................14
HDD and Optical Drive .....................................................................................14
Heat Sink, Memory Modules, Mini-PCIe and Touch Panel Control. .............14
Figure 11: Open system ............................................................................................16

Cybernet iOne-H19 Product Orientation
Page 1
Introduction
Congratulations for purchasing the iOne-H19. The LCD-PC iOne Series is your best
Slim LCD PC choice. With the fantastic appearance and small form factor, it can easily
be set anywhere. The feature packed platform also gives you an exciting PC
experience.
iOne-H19 Series Specifications
Processor Support
The 2nd generation Intel® Core™ i3, i5 and Core™ i7 in the 1155 package up to 65W.
Motherboard Core Logic
Intel® H61 Express chipset (Sandy Bridge)
Memory Support
DDR3 1066/1333 MHz SO-DIMM SDRAM (Un-buffered Non-ECC)
2 DDR3 1333 MHz SO-DIMM slots (8GB Max)
Video & Graphics for H19
Intel® integrated H61 Chipset with Intel® HD Graphics
Intel GMA HD/Intel Clear Video HD Technology
Built-in support for 1080p HD video playback, HDMI 1.4 & Blu-ray 3D support
Supports Microsoft® DirectX 10.1, Shader Model 4.0 and OpenGL 3.0.
DVMT allocated as needed from 128MB to 1.70GB
Maximum display resolution 2560 x 1600.
Video & Graphics for H19G
Onboard NVIDIA GeForce GT 540M(630M) GPU
1.0GB sDDR3 128-bit RAM
1080p HD video playback, HDMI 1.4 & Blu-ray 3D support.
Supports Microsoft® DirectX 11, Shader Model 5.0 and OpenGL 4.1
Maximum display resolution 2560 x 1600.
Networking
Supports 2 PCI Express LAN 10/100/1000 Fast Ethernet by Realtek RTL8111E
Audio
2 internal speakers with 78dB+/-3dB @ 3W, 1 mic
HD Audio Codec Realtek® ALC892
Flexible 10-channel audio with jack sensing
Compliant with Azalia 1.0 Spec

Cybernet iOne-H19 Product Orientation
Page 2
Hard Disk Drive
One 3.5” SATA Hard Disk Drive - Any Capacity
Wall Mount
Support 75x75 / 100x100 VESA mounting hole.
Swivel Stand
System Base enables left/right rotation up to 60 degrees. Tilt from -5 to 60 degrees
LCD Panel
19" TFT LCD/LED panel screen 4:3 format display.
Expansion Slots
2 mini-PCIe (One full size and one half size)
Front Lower Right Bezel
On Screen Display Buttons
Volume Adjust
Brightness Adjust
Contrast Adjust
Mute/Exit
Menu/Enter
Right Side Bezel
1 power button
2 USB 2.0 ports (for mouse and keyboard)
Left Side Bezel
1 optical disk drive – 2.5” slim
Bottom I/O Panel
1 DC/IN port, 1 Serial port, 1 DVI-I port, 1 HDMI port, 2 LAN RJ-45 jack, 2 USB 3.0
ports, 2 USB 2.0 ports, 1 LPT port (Optional), 3 Audio jacks – Line in, Line Out and Mic
4 TV Tuner ports - - Optional with TV Tuner (COAX Cable In, RCA Composite Video In,
Audio Left & Audio Right), 1 CMOS clear button, 1 Reset button
Power Supply
180 Watt Power Adapter, AC Input: 100~240V AC, 2.5A, 50-60Hz.
DC Output: 19V, 9.5A only / 120 Watt Power Adapter, AC input: 100~240V AC, 47Hz
to 63 Hz. DC Output: 19V, 6.32A only.
Dimensions
47.5cm (H) x 43cm (W) x 25.5cm (D) (with stand)

Cybernet iOne-H19 Product Orientation
Page 3
Power Management
Power management of LCD-PC has the potential to save significant amounts of
electricity as well as deliver environment benefits.
To be energy efficient, turn off your display or set your LCD-PC to sleep mode after a
period of user inactivity.
Power Management in Windows OS
[Power Options] in Windows OS allow you to control the power management features of
your display and hard drive. Go to [Start] > [Control Panel].
Then click on the [Power Options] link.

Cybernet iOne-H19 Product Orientation
Page 4
Select a power plan that suits your personal needs. You may also fine-tune the settings
by clicking [Change plan settings].
The Shut Down LCD-PC Menu presents the options of Sleep (S3) & Shut Down (S5) for
rapid and easy management of your system power.

Cybernet iOne-H19 Product Orientation
Page 5
Power Management through ENERGY STAR qualified Monitors
(Optional)
The power management feature allows the LCD-PC to initiate a low-power or “Sleep”
mode after a period of user inactivity. When used with an external ENERGY STAR
qualified Monitor, this feature also supports similar power management features of the
monitor. To take advantage of these potential energy saving, the power management
feature can be set to behave in the following ways when the system is operating on AC
power:
•Turn off the display after 15 minutes.
•Initiate Sleep after 30 minutes.
Waking the System Up
The LCD-PC shall be able to wake up from power saving mode in response to a
command from any of the following:
•the power button,
•the network (Wake on LAN),
•the mouse
•the keyboard
Energy Saving Tips:
•Tune the settings in Power Options under Windows OS to optimize your LCD-
PC’s power management.
•Install power saving software to manage your PC’s energy consumption.
•Always disconnect the AC power cord or switch the wall socket off if your LCD-
PC would be left unused for a certain time to achieve zero energy consumption.

Cybernet iOne-H19 Product Orientation
Page 6
iOne-H19 Series Overview
Figure 1: Front View with Optional Webcam

Cybernet iOne-H19 Product Orientation
Page 7
Figure 2: Left side view with Optical Drive

Cybernet iOne-H19 Product Orientation
Page 8
Figure 3: Power Button and USB Ports
Figure 4: Touch Panel
Figure 5: IrDA Receiver for TV Tuner

Cybernet iOne-H19 Product Orientation
Page 9
On Screen Display Buttons
There are six buttons on the lower right bezel of the screen. From left to right they are:
Volume – Volume + Brightness – Contrast + Mute/Exit Menu/Enter
Volume - Press to decrease volume.
Volume + Press to increase volume.
Brightness- Press first to select Brightness adjustment. Press again to decrease
brightness. Press Contrast + to increase brightness. Brightness can also
be adjusted in Menu Mode.
Contrast + Press first to select Contrast adjustment. Press again to increase
contrast. Press Brightness – to decrease contrast. Contrast can also be
adjusted in Menu Mode.
Mute/Exit Press once to toggle Mute On or Off.
Also functions as Exit button in the Menu Mode.
Menu/Enter Press once to get to On-Screen display Mode to allow various
adjustments as listed below.
Also functions as the Enter or Select button in Menu Mode.

Cybernet iOne-H19 Product Orientation
Page 10
On Screen Display Usage
When the Menu button is pressed, the on-screen display appears as pictured above.
When in Menu Mode you can move to the various icons with the – (left) or + (right)
button. When you are at the icon you wish to adjust, press Menu again (Enter) to
change the color of the icon and then toggle your desired adjustment by again pressing
either – (left) or + (right). The screen will exit automatically in a matter of seconds if no
selection is made.
Contrast Select to toggle greater or lesser contrast.
Brightness Select to toggle greater or lesser brightness.
Select to adjust the appearance of the screen to “Cool”.
Select to adjust the appearance of the screen to “Warm”.
Screen Horizontal and Vertical adjustment, OSD display time setup.
Select to toggle through the languages offered.
Select to reset all LCD Display settings
OSD Firmware EEPROM version information.
Screen mode selection for 16:9 or 4:3

Cybernet iOne-H19 Product Orientation
Page 11
Figure 6: Back view
Figure 7: Bottom Panel I/O Ports

Cybernet iOne-H19 Product Orientation
Page 12
Figure 8: System Ventilation Fan
Figure 9: Heat Sink Ventilation, System Ventilation and Stand

Cybernet iOne-H19 Product Orientation
Page 13
System Assembly
This chapter provides system assembly information and procedures. While performing
any installation, use a grounded wrist strap before handling computer components and
carefully follow all installation procedures. Static electricity may damage the
components.
This chapter will include instructions for how to install CPU, heat sink, memory
modules, hard disk drive (HDD), optical disk drive (ODD), mini-PCI card, mini-PCIE
card and IrDA module.
Necessary Tools
A Phillips screwdriver can be used to do most of the installation. One
with a magnetic head is recommended. Applied maximum torque is 5kg.
Pliers can be used as an auxiliary tool to connect some connectors or
cables.
Forceps/tweezers can be used to pick up tiny screws or set up the
jumpers.
Rubber gloves can prevent injury from static charge.
Electric screwdriver can be used to secure all screws more quickly.

Cybernet iOne-H19 Product Orientation
Page 14
Orientation of Key Parts
Figure 10:System Fan and Ventilation, HDD and Optical Drive, Heat Sink, Memory
Modules, Mini-PCIe and Touch Panel Control.
S
y
stem Fan and Ventilation HDD and O
p
tical Drive
Heat Sink Memory Modules Mini-PCIe Card
and Touch Panel Control