CYP PU-1H7HBTL User manual

PU-1H7HBTL
1 HDMI to 7 HDBaseT™ LITE Splitter (60m)
including additional HDMI output
Operation Manual
Operation Manual

SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or
operate this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
• Always follow basic safety precautions to reduce the risk of re,
electrical shock and injury to persons.
• To prevent re or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts
inside the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the PSU
if it is damaged.
• Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow for
sufcient space for air to circulate around the unit.
REVISION HISTORY
VERSION NO. DATE DD/MM/YY SUMMARY OF CHANGE
RDV1 27/06/13 Preliminary Release

CONTENTS
1. Introduction ............................................ 1
2. Applications ........................................... 1
3. Package Contents ................................ 1
4. System Requirements ............................ 1
5. Features .................................................. 2
6. Operation Controls and Functions ....... 3
6.1 Front Panel ........................................3
6.2 Rear Panel .........................................3
6.3 IR Cable Pin Assignment..................5
7. Connection Diagram ............................ 6
8. Specications ........................................7
8.1 CAT5e/6/7 Cable Specication .....8
9. Acronyms ............................................... 8

1
1. INTRODUCTION
The HDMI over HDMI and CAT5e/6/7 Transmitter can support
resolutions up to 1080p Full HD, 4Kx2K timing, 3D and multi-channel
digital audio formats to one HDTV and seven CAT5e/6/7 outputs.
The HDMI can be connected to HDMI display for instant nearby
display and the CAT5e/6/7 can be connected to CAT5e/6/7 to HDMI
Receivers for distance up to 60 meters.
2. APPLICATIONS
• Household entertainment sharing and control
• Lecture room display and control
• Showroom display and control
• Meeting room presentation and control
• Classroom display and control
3. PACKAGE CONTENTS
• HDMI over HDMI & CAT5e/6/7 Transmitter
• IR Receiver x 1
• IR Blaster x 1
• 24V DC Power Adaptor
• Power Cord
• Operation Manual
4. SYSTEM REQUIREMENTS
• Source equipment with HDMI output connector
• Display TV/Monitor with HDMI input connector
• HDMI over CAT5e/6/7 Receivers with industry CAT5e/6/7 cables

2
5. FEATURES
• HDMI with 3D & 4Kx2K supported, HDCP and DVI compliant
• The HDMI and CAT5e/6/7 outputs are playing the same source
simultaneously
• Supports one HDTV and seven CAT5e/6/7 outputs
• Supports data rate from 250Mbps up to 3Gbps
• Supports wide range of PC resolutions from VGA to WUXGA
and HDTV resolutions up to 4Kx2K (3840x2160@30Hz and
4096x2160@24Hz).
• Supports LPCM 7.1CH, Dolby TrueHD, Dolby Digital Plus and DTS-HD
Master Audio transmission (32-192kHz sample rate)
• Supports distances up to 60 meters through CAT5e/6/7 cables
• Can select Standard or TV EDID
• Supports USB service port
• Supports Bi-directional IR control
• The 3D signal display follow by display TV’s EDID
Note:
1.ThissystemwastestedwithCAT6/23AWGcables,resultsmayvary
 withcablesofadifferentspecication.
2.DisplayingHDMI4Kx2Kresolutionrequirethestandard4Kx2KHDMI
 cableanddisplayinorderforproperimagedisplaying.


3
6. OPERATION CONTROLS AND FUNCTIONS
6.1 Front Panel
POWER SYNC
HDMI
LINK LINK 1 LINK 2 LINK 3 LINK 4 LINK 5 LINK 6 LINK 7
CAT5e/ 6/ 7 OUT
1 2 3 4
1 POWER LED: Once the power supply is connected the LED will
illuminate.
2 SYNC: This LED will illuminate when the HDMI input port connected
to the source.
3 HDMI LINK: This LED will illuminate when HDMI output is connected
to TV or display monitor.
4 LINK 1~7: The link LED will illuminate when CAT5e/6/7 output(s)
has been connected to the Receiver(s) and the Receiver(s) has
connected with display that shows image on screen.
6.2 Rear Panel
1HDMI OUTHDMI IN 2 3 4 5 6 7
SERVICE
CAT5e/ 6/ 7 OUT
STD TV
DC 24V
IR IN IR OUT
EDID
1 2 3 6 7 84 5
1 HDMI IN: Connect with source equipment such as DVD/Blu-ray or
PS3 player.
2 HDMI OUT: Connect to HDMI display for instant image display or
cascade with another family type Transmitter.
3 CAT5e/6/7 OUT 1~7: Connect these ports to CAT5e/6/7 to HDMI
Receivers with CAT5e/6/7 cable to extend the signal up to 60m.
4 IR IN: Connect with IR Extender to receive IR signal from Transmitter
side and blast out at Receiver side. Ensure that remote controller
being used is within the direct line-of-sight of the IR Extender.
5 IR OUT: Connect with IR Blaster to blast out the IR signal received
from the Receiver side. Place the IR Blaster in direct line-of-sight of

4
the equipment to be controlled.
6 EDID STD/TV: The default factory setting is on TV, leave as it is
when the display is properly. The unit will detect the 1st CAT5e/6/7
output’s EDID when it obtain a 4Kx2K EDID and send out the signal
accordingly to other output ports. If the 1st CAT5e/6/7 output is
without a 4Kx2K's EDID the unit will detect all output's EDID and
send out the signal that all outputs can accept.
This device obtain the last memory function therefore, the device
will use the last output port 1's EDID when output port 1 is not
connected to a display after power cycling or switching in
between the EDID setting.
Switch to STD to use build-in EDID if the display has problem.
STD EDID’s video at 1080p@60Hz and audio at LPCM 2CH.
7 SERVICE: This slot is reserved for factory service only.
8 DC 24V: Plug the 24V DC power supply into the unit and connect
the adaptor to an AC outlet.

5
6.3 IR Cable Pin Assignment
3
1
3
1
2
2
Power 3.3 V
IR Blaster Signal
NC
IR Signal
Power 3.3 V
Grounding
IR Extender
IR Blaster

6
7. CONNECTION DIAGRAM
IR BLASTER
1.5m
60°
IR RECEIVER
7m
3m 3m
60°
m
1HDMI OUTHDMI IN 2 3 4 5 6 7
SERVICE
CAT5e/ 6/ 7 OUT
STD TV
DC 24V
IR IN IR OUT
EDID
CAT5e/6 In
Link
IR1 Extender
IR2 Blaster
Power
Blu-ray or PS3 Player
3D TV/Display 3D TV/Display
HDMI Receiver
HDMI
HDMI