CYP EL-2600V User manual

EL-2600V
HDBaseT Transmitter with Trigger Control
4K UHD+HDMI/DP/VGA/USB
Driver User Guide

®
registered trademarks of HDMI licensing Administrator, Inc.

3
DISCLAIMERS
The information in this manual has been carefully checked and is
believed to be accurate. CYP (UK) Ltd assumes no responsibility for any
infringements of patents or other rights of third parties which may result
from its use.
CYP (UK) Ltd assumes no responsibility for any inaccuracies that may be
contained in this document. CYP (UK) Ltd also makes no commitment to
update or to keep current the information contained in this document.
CYP (UK) Ltd reserves the right to make improvements to this document
and/or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted, transcribed,
stored in a retrieval system, or any of its part translated into any language
or computer le, in any form or by any means—electronic, mechanical,
magnetic, optical, chemical, manual, or otherwise—without express
written permission and consent from CYP (UK) Ltd.
© Copyright 2020 by CYP (UK) Ltd.
All Rights Reserved.
Version 1.1
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may be
trademarks of the companies with which they are associated.

4
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or operate
this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
• Always follow basic safety precautions to reduce the risk of re,
electrical shock and injury to persons.
• To prevent re or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts inside
the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the PSU if
it is damaged.
• Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow for
sucient space for air to circulate around the unit.
REVISION HISTORY
VERSION NO. DATE SUMMARY OF CHANGE
v1.00 21/09/2020 First release

5
CONTENTS
1. Introduction...........................................6
2. DRIVER PROPERTIES..............................6
3. IP NETWORK CONNECTION...................6
4. DEVICE SPECIFIC COMMAND ................7
4.1 Set Power Reboot...................................... 7
4.2 Set Auto Switching Mode....................... 7
4.3 Set Key Lock................................................. 7
4.4 Set Route Preset......................................... 7
4.5 Set HDBT Audio Mode............................. 7
4.6 Set Audio Mixer Source Volume........... 8
4.7 Set Microphone Mode............................. 8
4.8 Set Microphone Volume ......................... 8
4.9 Set Audio Mixer Line Volume ................ 8
4.10 Set Analog Output Volume ................. 8
4.11 Set Analog Output Mute ..................... 8
4.12 Set Phantom Mode ................................ 8

6
1. INTRODUCTION
This driver has been designed to provide two-way control of the CYP 9x2
Multi-format Presentation Scaler, via RS232 or TCP/IP.
2. DRIVER PROPERTIES
The property of this driver is shown below.
Figure 1: Driver Properties
Driver Version Driver version number
Debug Mode Support use only
Debug Level Support use only
Command Delay Milliseconds a delay of millisecond between
commands
Connected To Network Shows operational status of driver
3. IP NETWORK CONNECTION
If an IP driver used, the IP address of the A/V Scaler is entered in the usual
way in connections -> Network.

7
4. DEVICE SPECIFIC COMMAND
In addition to the usual A/V Scaler functionality supported by Control4,
there are a number of device specific commands for the A/V Scaler
switching.
4.1 Set Power Reboot
Power Status Reboot
4.2 Set Auto Switching Mode
Video Output Channel HDMI or HDBT
Switching Mode OFF or Auto Switch
4.3 Set Key Lock
Key Lock Status Locked or Unlocked
4.4 Set Route Preset
Route Preset 1 to 4
4.5 Set HDBT Audio Mode
HDBT Audio Mode
1 [Source audio only]
2 [Line audio only]
3 [Microphone only]
4 [Source + Microphone]
5 [Source + Line]

8
4.6 Set Audio Mixer Source Volume
Volume(dB) -120 to 18
4.7 Set Microphone Mode
Microphone Mode Front Panel or WebGUI
4.8 Set Microphone Volume
Volume(dB) 0 to 60
4.9 Set Audio Mixer Line Volume
Volume(dB) -120 to 18
4.10 Set Analog Output Volume
Volume(dB) -103 to 24
4.11 Set Analog Output Mute
Audio Mute Status Mute or Unmute
4.12 Set Phantom Mode
Phantom Mode OFF / 5V / 48V