CYP PUV-1210PL-TX User manual

PUV-1210PL-TX & RX
HDBaseT™ LITE Transmitter 60m
(4K, HDCP2.2, HDMI2.0, PoH)
OPERATION MANUAL

3
DISCLAIMERS
The information in this manual has been carefully checked and is
believed to be accurate. CYP (UK) Ltd assumes no responsibility for any
infringements of patents or other rights of third parties which may result
from its use.
CYP (UK) Ltd assumes no responsibility for any inaccuracies that may be
contained in this document. CYP (UK) Ltd also makes no commitment to
update or to keep current the information contained in this document.
CYP (UK) Ltd reserves the right to make improvements to this document
and/or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted, transcribed,
stored in a retrieval system, or any of its part translated into any language
or computer le, in any form or by any means—electronic, mechanical,
magnetic, optical, chemical, manual, or otherwise—without express
written permission and consent from CYP (UK) Ltd.
© Copyright 2011 by CYP (UK) Ltd.
All Rights Reserved.
Version 1.1 August 2011
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may be
trademarks of the companies with which they are associated.

4
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or operate
this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
• Always follow basic safety precautions to reduce the risk of re,
electrical shock and injury to persons.
• To prevent re or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts inside
the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the PSU if
it is damaged.
• Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow for
sucient space for air to circulate around the unit.
REVISION HISTORY
VERSION NO. DATE SUMMARY OF CHANGE
v1.00 06/06/2017 First release

5
CONTENTS
UPDATE CONTENTS

6
1. INTRODUCTION
The HDMI over single CAT5e/6/7 Transmitter and Receiver set can send
uncompressed audio/video and iP data over a single run of CAT5e/6/7
cable at a distance up to 60 meter. it has the added benet of control
through the built-in RS-232 and IR ports. The Receiver (PD) can be
powered by the PoE 48V function of the Transmitter (PSE), allowing for
greater exibility in installations.
2. APPLICATIONS
48V PoE from Transmitter (PSE) to Receiver (PD)
Household entertainment sharing and control
Lecture room display and control
Showroom display and control
Meeting room presentation and control
Classroom display and control
3. PACKAGE CONTENTS
Transmitter Package
1×HDMI to CAT5e/6/7 (with IR/RS-232) Transmitter
1×IR Blaster
1×IR Extender
1×48 V/0.83 A DC Power Adaptor
Operation Manual
Transmitter Package
1×CAT5e/6/7 to HDMI (with IR/RS-232) Receiver
1×IR Blaster
1×IR Extender
Operation Manual
Please note, packages are sold separately.
4. SYSTEM REQUIREMENTS
Input source equipment such as PS3/Blu-ray player and output HD TV/
display.

7
5. FEATURES
HDMI with 3D, 4K2K support, HDMI & DVI Compliant
Supports CEC bypass
Simultaneous transmission of uncompressed data over a single
CAT5e/6/7 cable up to 60m
4Play™ convergence: HDMI, PoE & Control (IR & RS-2232)
Supports resolution up to 4K2K@50/60 & YUV_420 and 21:9
Supports standard 48V from Transmitter (PSE) to Receiver (PD)
Installation Friendly
Supports HDMI input/Output cable distance up to 5m at 4K2K@50/60
& YUV_420
Note:
1. The standard 48V PoE function is designed for powering compatible
Receiver units only---non-PoE Receivers will need their own power supply.
Receivers of another brand may not be compatible.
2. Displaying HDMI 3D and 4K2K contents, equivalent source signal and
HDMI cable are required in order to secure the quality.

8
3. 6. OPERATION CONTROLS AND FUNCTIONS
6.1 Transmitter Front and Rear Panels
POWER
LINK
RS-232 IN
STD UPDATE
6 7 98
CAT5e/6/7 OUT
IR2
EXTENDER
HDMI IN
DC 48V
IR1
BLASTER
1 3 4 52
RearFront
1DC 48V: Plug the 48V DC power supply into the unit and connect the
adaptor to an AC outlet.
2IR1 BLASTER: Connect to the supplied iR Blaster cable for IR signal
transmission. Place the IR Blaster in direct line-of-sight of the
equipment to be controlled.
3IR2 EXTENDER: Connect to the supplied iR Extender cables for IR
signal reception. Ensure that remote being used is within the direct
line-of-sight of the IR Extender.
4CAT5e/6/7 OUT: Connect to the Receiver unit with a single CAT5e/6/7
cable for transmission of all data signals.
5HDMi IN: Connect to HDMI source equipment such as a DVD or Blu-
ray player.
6STD/UPDATE Switch: This switch is reserved for factory use only.
7RS-232 IN: Connect to a PC or Laptop with D-Sub 9-pin male cable for
the transmission of RS-232 commands.
8POWER LED: This LED will illuminate when the device is connected to
a power supply.
9LiNK LED: This LED will illuminate when both the Transmitter and
Receiver are connected through CAT cable. When it blinks regularly
it states the Transmitter is NOT sending signal but the Transmitter
and Receiver are linked and if it blinks irregularly it states an error has
occurred.

9
6.2 Receiver Front and Rear Panels
CAT5e/6/7 IN
IR1
EXTENDER
HDMI OUT
IR2
BLASTER POWER
LINK
RS-232 OUT
STD UPDATE
1 42 3
RearFront
6 7 85
1IR2 BLASTER: Connect to the supplied IR Blaster cable for IR signal
transmission. Place the IR Blaster in direct line-of-sight of the
equipment to be controlled.
2IR1 EXTENDER: Connect to the supplied IR Extender cables for IR
signal reception. Ensure that remote being used is within the direct
line-of-sight of the IR Extender.
3CAT5e/6/7: Connect to the Transmitter unit with a single CAT5e/6/7
cable for transmission of all data signals.
4HDMI OUT: Connect to a HDMI equipped TV/monitor for display of
the HDMI input source signal.
5STD/UPDATE Switch: This switch is reserved for factory use only.
6RS-232 OUT: Connect to the device that is to be controlled (via D-Sub
9-pin female cable) by RS-232 commands.
7POWER LED: This LED will illuminate when the device is connected to
a power supply.
8LINK LED: This LED will illuminate when both Transmitter and Receiver
are connected through CAT cable. When it blinks regularly it states the
Receiver is NOT sending signal but the Transmitter and Receiver are
linked and if it blinks irregularly it states an error has occurred.

10
6.3. IR Cable Pin Assignment
3
1
2
3
2
1Power
IR Blaster Signal
NC
IR Signal
Power
Ground
IR Extender
IR Blaster
6.4. D-Sub 9 Pin Denitions
Pin Dene TX / RX
1 N/C
2 TxD / RxD
3RxD / TxD
4 N/C
5 GND
6 N/C
7 N/C
8 N/C
9 N/C

11
7. CONNECTION DIAGRAM
TV or Monitor
CAT5e/6/7 IN
IR1
EXTENDER
HDMI OUT
IR2
BLASTER
POWER
LINK
RS-232 OUT
STDUPDATE
POWER
LINK
RS-232 IN
STDUPDATE
CAT5e/6/7 OUT
IR2
EXTENDER
HDMI IN
DC 48V
IR1
BLASTER
1.5m
60°
1.5m
60°
7m
3m 3m
60°
7m
3m
3m
60°
RS-232 Equipped
PC or Notebook
RS-232 Equipped
HDMi Switcher
Notebook
DVD or Blu-ray Player
Power
Supply
iR Blaster
HDMi
HDMi
iR Extender
iR Extender
iR Blaster RX
TX
RS-232
RS-232
CAT5e/6

12
8. SPECIFICATIONS
Video Bandwidth 340MHz / 10.2Gbps
Transmitter
inputs 1 x HDMI
1 x IR Extender
1 x RS-232
Outputs 1 x CAT5e/6/7
1 x IR Blaster
Receiver
inputs 1 x CAT5e/6/7, 1 x IR Extender
Outputs 1 x HDMI, 1 x RS-232, 1 X IR Blaster
HDMI I/O Resolution HD: 480i~4K2K@24/25/30 & 50/60@YUV_420
PC: VGA ~ WUXGA (RB)
HDMI I/O Cable Distance In: 10m/1080p@8-bit or 12-bit and 5m@4K2K
Out: 10m/1080p@8-bit, 5m/1080p@12-bit and 5m@4K2K
CAT5e/6/7 I/O Cable
Distance
Up to 60m
IR Frequency 30~50kHz
ESD Protection Human Body Model:
±8 kV (air-gap discharge)
±4 kV (contact discharge)
Power Supply 48 V/0.83 A DC (US/EU Standards, CE/FCC/UL certied)
Dimensions 108mm (W) x 108mm (D) x 25mm (H)/Jacks Excluded
108mm (W) x 116mm (D) x 29mm (H)/Jacks included
Weight 370g/TX, 366g/RX
Chassis Material Metal
Silkscreen Colour Black
Power Consumption 13.5w (Max)
Operating Temperature 0 °C~40 °C/32 °F ~104 °F
Storage Temperature −20 °C~60 °C/−4 °F~140 °F
Relative Humidity 20~90 % RH (non-condensing)

13
8.1 CAT5e/6/7 Cable Specication
Cable
Type
Range Pixel clock
rate
Video Data
Rate
Supported
Video
CAT5e/6/7 60 m <=225 MHz <=5.3 Gbps
(HD Video)
Up to 1080p, 60
Hz, 36 bits, 3D
(data rates lower
than 5.3 Gbps or
below 225 MHz
TMDS clock).
35 m >225 MHz > 5.3 Gbps
(Ultra HD
Video)
4K2K, 30Hz
video formats

14
8.2 Timing Support Chart
iNPUT OUTPUT
640×480@60/72/75/85  
800×600@56/60/72/75/85  
1024×768@60/70/75/85  
1280×720@60  
1280×1024@60  
1600×1200@60  
1920×1200@60RB  
3840×2160p@24/25/30  
4096×2160p@24  
4096×2160p@50/60(YUV_420)  
480i/576i  
480p/576p  
720p@50/60  
1080i@50/60  
1080p@50/60  
1080p@24/25/30  

15
9. ACRONYMS
ACRONYM COMPLETE TERM
CAT5e Category 5 Cable
CAT6 Category 6 Cable
CAT7 Category 7 Cable
CEC Consumer Electronics Control
DVI Digital Visual interface
HDCP High-bandwidth Digital Content Protection
HDMI High Denition Multimedia interface
IR Infrared
PD Powered Device
PSE Power Sourcing Equipment

CYP (UK) Ltd., Unit 7, Shepperton Business Park, Govett Avenue, Shepperton,
Middlesex, TW17 8BA
Tel: [phone] | Fax: [phone]
Email: [email protected]
www.cypeurope.com
v1.00