D-CUT TC-230 User manual

OPERATION MANUAL
D-CUT Flooring / Trim Cutter TC-230
www.dcutproducts.com

2
SAFETY RULES FOR THE FLOORING CUTTER
1. READ AND UNDERSTAND THIS INSTRUCTION MANUAL BEFORE
OPERATING THE D-Cut MULTI-FLOORING CUTTERS.
2. If you are not thoroughly familiar with the operation of D-Cut Multi-flooring
Cutter, obtain advice from a qualified instructor or call 630-916-9100 USA
3. Stay alert. Do not operate while under the influence of drugs, alcohol, or
medication.
4. Always wear safety approved eye protection with side shields(ANSI Z87.1)
5. Keep work area free of debris.
6. Keep children and unauthorized persons away from the D-Cut Multi-flooring
Cutter and work area.
7. Make sure tool is secure. Operate only on a firm substrate or solid stand.
8. Use the right tool. Do not force the D-Cut Multi-flooring Cutter or use it for a
job for which it was not designed; use only on approved materials.
9. Keep the blade sharp. A dull blade will not perform properly.
10. Always keep hands away from blade while operating or carrying the cutter.
11. Do not alter or misuse this tool. The D-Cut Multi-flooring Cutter is precision
built; modifications not specified in this manual may result in a dangerous
and unsafe environment.
12. Maintain the D-Cut Multi-flooring Cutter with care. Keep Blade sharp and
clean. Follow instructions for changing accessories.
13. Use only recommended accessories. The use of improper accessories may be
hazardous and cause injuries.
14. Never leave the D-Cut Multi-flooring Cutter unattended. Keep the cutting
head in a close position with lock pins when the cutter is not in use.

3
CUTTING AND C
Installation of the Cutter(1)
Install the handle assembly to
the cutter base as shown.
Warning: Do not put your
fingers against the sharp edge
o
f
t
h
e
b
l
ade
at
a
n
y
t
im
e
.
Angle Cut
Position the guide bar at 45°.
Insert a baseboard or a shoe
mold between the cutting
blade and the base, flush with
the guide bar as shown, then
pull the handle down to
complete a cut.
Straight Cut
Insert the floor plank between
the cutting blade and the base,
flush with the guide bar on the
working table, hold the plank
and pull handle down to
complete a cut.

4
Bevel Cut (1)
Make a straight cut on a
workpiece to your
measurement and then pull
the knob as pointed by an
arrow, adjust the cutter head
to your desired angle. Pull
out the handle from the base
to change the handle
position on the cutting head.
Bevel Cut (2)
Insert the workpiece between
the cutting blade and flush the
working table with the guide
bar, and stop the edge of the
workpiece from previous
straight cut at the cutting base
where you can see and feel it
while you're moving along the
workpiece, hold the workpiece
firmly, and then pull the handle
down to complete a cut.
Angle Compensation
Pull out the knob at the end
of the working table, and
move the table end up or
down to compensate plus or
minus 1-2 degree if needed.

5
Lock the Cutting Head
Use the provided Lock Pin to
tuck the hole on the main
column as shown. Make sure
the cutting blade is in a close
position when the cutter is not
in use.
T
ransport
Once the lock pins firmly
locked the cutting head and
pull out the handle to carry the
cutter as shown.
Changing the Blade
Use provided Allen wrench to
remove the four screws, then
carefully move the blade out of
the small blade holder.
Note: the flat side of the blade
should face the working table.
Warning: Do not put your
fingers against the sharp edge of
the blade at any time.

6
Explosive View

7
Parts Q’ty Parts Q’ty
1 Lock Nut M10 2 43 Guide Bar 1
2 Wheel 2 44 Guide Bar Socket 15
3 Flange Nut M10 2 45 Screw M5 × 8 30
4 Washer φ10 2 46 Working Table 1
5 Wheel shaft 2 47 Rear Cutter Frame 1
6 Sleeve 2 48 Spring Washer φ5 2
7 Cutter Base 1 49 Round Head Screw M5 × 20 2
8 Nut M12 2 50 Flat Head Screw M5 × 20 2
9 Screw M5 × 14 4 51 Spring B 1
10 Nylon Bar 1 52 Spring B Base 1
11 Main Column 2 53 Knurled Screw M8 B 1
12 Guide Sleeve 2 54 Angle Compensation Lock Pin 1
13 Screw M8 × 14 2 55 Angle Compensation Base 1
14 Spring A 1 56 Working Table Base Assembly 1
15 Screw M8 × 10 2 57 Nut M10 15
16 Right Side Frame 1 58 Screw M8 × 25 8
17 Screw M8 × 25 4 59 Rubber Foot 2
18 Spring Washer φ12 2 60 Screw M5 × 25 2
19 Customized Screw M12 2 61 Screw M5 × 12 2
20 Rotation Shaft 2 62 Washer φ5 12
21 Right Angle Plate 1 63 Lock Nut M5 2
22 Rotation Shaft Base 2 64 Left Side Frame 1
23 Screw M6 ×12 4 65 Screw M8 × 25 6
24 Blade Holder 1 66 Spring Washer φ8 8
25 Lock Pin Base 2 67 Washer φ8 8
26 Screw M4 × 10 2 68 Left Angle Plate 1
27 Lock Pin 2 69 Screw M6 ×16 4
28 Screw M12 × 40 2 70 Cushion Block 2
29 Spring Washer φ12 2 71 Screw M5 × 14 4
30 Aluminum Eccentric Bar 1 72 Knurled Angle Knob 2
31 Nylon Cam Ring 2 73 Screw M5 × 10 4
32 Screw M6 × 20 2 74 Rotation Plate 2
33 Handle Base 2 75 Angle Adjustment bar 2
34 Knurled Knob 1 76 Spring C 2
35 Handle A 1 77 Spring C Base 1
36 Knurled Screw M8 A 1 78 Screw M6 × 10 2
37 Handle B 1 79 Angle Adjustment Base 1
38 Nut M4 2 80 Screw M8 × 16 2
39 Right ABS Handle 1 81 Rotation Gear 2
40 Screw M4 × 30 2 82 Lock Nut M8 2
41 Left ABS Handle 1 83 Supporting Plate 2
42 Shaft for Eccentric Bar 1 84 Blade 1
Explosive View