D-Link DSL-360T User manual

1
Before You Begin
Make sure you have all the necessaryinformation and equipment on hand before beginning
the installation.
CheckYourPackageContents
This product can beset
up using any currentweb
browser, i.e.,Internet
Explorer 6or Netscape
Navigator 6.2.3.
DSL-360T
ADSLModem
DSL-360T ADSL Modem
CD-ROM(containingManual)
Ethernet (CAT5 UTP) Cable
Telephone Cable
Power Adapter
Ifanyoftheabove items are missing, please contact your reseller
Using a power supply
with a different voltage
rating will damage and void
the warrantyfor this product.

2
Connecting the Modem to YourComputer
A. First, connect the power adapter to the receptor at the back panel ofthe
DSL-360Tand then plug the other end of the power adapter to a wall outlet or
power strip. The Power LED will turn ON to indicate proper operation.
B. Insert one end of the cable into the Ethernet port on the back panelofthe
DSL-360Tand the other end ofthe cable to an Ethernet Adapter or available
Ethernet port on your computer.
ADSL port -
connect to
ADSL line
Ethernet port -
connect to
Ethernet cable
Factory
Reset
button
Power input -
connect to power
adapter

3
Configuring the Modem
To use your Web browser to access the web pages used to setup the Modem, your computer
must be configured to Obtain an IPaddress automatically”,that is, you must change the
IPnetwork settings ofyour computer so that it is a DHCPClient. Ifyou are using Windows
XP and do not knowhowto change your network settings, skip ahead to Appendix A and
read the instructionsprovided. You mayalso read the User Manual for instructionson
changing IPsettings for computers running Windows operating systems.
Open your Web browser and type
http://192.168.1.1”into the URLaddress
box.Then pressthe Enter or Return key.
The Login pageappears.
Type admin”for the
Login Name and
admin”in the
Password field.
Click Login

4
Configuring the Modem(continued)
Once you havelogged in, the Home screen will appear.Click the Setup tab to go to the Setup
menu and configure the Modem.
Click Setup

5
Configuring the Modem(continued)
In the Setup menu, click the Connection button to go to the configuration menu for the
Internet connection.
Click Connection

6
Configuring the Modem(continued)
In the Connection menu, type the Username and Password used to verifythe identityof
your ISPaccount. It maybe necessaryto change the PPPencapsulation Type used for your
connection. You mayalso need to change the VPI or VCI value. YourISPwill give these
settings to you if theyneed to be changed. Click the Apply button when you have entered all
the information. To save the changes made to Connection, click the Tools tab and followthe
instructions on the next page.
A. Type the Username
and Password used for
your account.
D. Click Tools when
you have applied the
newsettings.
C. Click the Apply button
after you have entered the
account information.
B. Check the PPP
encapsulation Type,
VPI: and VCI: - ifthese
values are not correct,
change these according
to the instructions of
your ISP.

7
Configuring the Modem(continued)
Nowsave the changesyou have just made. The Save function is accessed from the System
Commands menu. Click the System Commands button to viewthat menu.
Click System Commands to
viewthe menu used to save
changes.

8
Configuring the Modem(continued)
To save the newsettings, click the SaveAll button in the System Commands menu. Aftera
fewseconds, the changes will be saved. The Modem will automaticallyestablish the Internet
connection after a fewmore seconds.
Wait a fewseconds forthe Internet connection to be established and proceed to access the
Internet via your web browser.
Click SaveAll to save
the newsettings.

9
Appendix
For additional settings or information, refer to the Advanced, Tools, or Status tabs on the
web-management interface; or to the manual located on the CD-ROM.
Configuring IPSettings in Windows XP
Use the following steps to configure a computer running Windows XPto be a DHCPclient.
1. From the Start menu on your desktop, go to Settings, then click on Network
Connections.
2. In the Network Connections window, right-click on LAN (Local Area Connection),
then click Properties.
Right-click on the Local Area
Connection icon and Select the
Properties option from the pull-
down
menu.

10
3. In the General tab of the Local Area Connection Properties menu, highlight Internet
Protocol (TCP/IP) under This connection uses the following items:”byclicking on it
once. Click on the Properties button.
4. Select Obtain an IPaddress automatically”byclicking once in the circle. Click the
OK button.
Your computer is nowreadyto use the Modem’s DHCPserver.
Click Properties
Select Obtain an IPaddress
automatically in the Internet
Protocol (TCP/IP) Properties window