D-Link DSL-362T User manual

DSL-362T
ADSLModem
User s Manual
First Edition (February 2004)
651D362T.015

DSL-362TDSL Modem User s Guide
ii
CE MarkWarning
This is aClass Bproduct. In adomestic environment, this product maycause radio interference inwhich case
the user may be required to take adequate measures.

DSL-362TADSL Modem User s Guide
iii
LIMITATION OF LIABILITY
IN NO EVENT WILL D-LINK BELIABLEFOR ANY DAMAGES, INCLUDING LOSS OF DATA, LOSS OF PROFITS, COST OF COVER
OR OTHER INCIDENTAL, CONSEQUENTIAL OR INDIRECTDAMAGES ARISINGOUT THE INSTALLATION, MAINTENANCE, USE,
PERFORMANCE, FAILUREOR INTERRUPTION OF AD- LINK PRODUCT, HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY.
THIS LIMITATION WILL APPLY EVEN IF D-LINK HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
IF YOU PURCHASED AD-LINK PRODUCT IN THE UNITED STATES, SOME STATES DO NOT ALLOW THE LIMITATION OR
EXCLUSION OF LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVELIMITATION MAY NOT APPLY TO
YOU.
LimitedWarranty
Hardware:
D-Link warrants each of its hardware products tobe free from defects in workmanship and materials under normal use and service
for aperiod commencing on the date of purchasefrom D-Link or its Authorized Reseller and extending for the length of time
stipulated by the Authorized Reseller or D-Link Branch Office nearest to the place of purchase.
This Warranty applies on the condition that the product Registration Card is filled out and returned to a D-Link office within ninety
(90) days of purchase. A list of D-Link offices is provided at the back of this manual, together with a copy of the Registration Card.
If the product proves defectivewithin the applicable warranty period, D-Link will provide repair or replacement of the product.
D-Link shall havethe sole discretion whether to repair or replace,and replacement productmay be newor reconditioned.
Replacement product shall be of equivalent or better specifications, relativeto the defectiveproduct, but need not be identical. Any
product or part repaired by D-Linkpursuant to this warranty shall haveawarranty period of not lessthan 90 days, from date of
suchrepair, irrespectiveof any earlier expiration of originalwarranty period. When D-Link provides replacement, then the defective
product becomes the property of D-Link.
Warranty service may beobtainedby contacting aD-Link office within the applicable warrantyperiod,and requesting aReturn
MaterialAuthorization (RMA) number. If aRegistration Card for the product in question has not been returned toD-Link, thena
proof of purchase (suchas acopy of the dated purchase invoice)must be provided. If Purchaser's circumstances require special
handling of warranty correction, then at the time of requesting RMA number, Purchaser may also proposespecialprocedure as may
be suitable to the case.
After an RMA number is issued, the defectiveproduct mustbe packaged securely in the original or other suitable shipping package
to ensure that it will not be damaged in transit, and the RMA numbermust be prominently marked on the outside of the package.
The package must be mailed or otherwise shipped to D-Link with all costs of mailing/shipping/insurance prepaid. D-Link shall
never be responsible for any software, firmware, information, or memory data of Purchaser contained in, stored on, or integrated
with any product returned to D-Link pursuant to this warranty.
Any package returned toD-Link without an RMA number will be rejected and shipped back to Purchaser at Purchaser's expense,
and D-Link reserves the right in such a case to levy a reasonable handling charge in addition mailing or shipping costs.
Software:
Warranty service for software productsmay be obtained by contacting aD-Link office within the applicable warranty period. Alist
of D-Link offices is providedat the back of this manual, together withacopy of the Registration Card. If a Registration Card for the
product in question has not been returned to a D-Link office, then a proof of purchase (such as a copy of the dated purchase invoice)
must be provided whenrequesting warranty service. The term "purchase" in this software warrantyrefers to the purchase
transaction and resulting license to use such software.
D-Link warrants that itssoftware products will perform in substantial conformance with the applicable productdocumentation
provided by D-Link with suchsoftware product, for aperiod of ninety (90)days from the date of purchase from D-Link or its
Authorized Reseller. D-Link warrants the magnetic media, on whichD-Link provides its software product, againstfailure during
the same warranty period. This warranty applies to purchasedsoftware, and to replacement software provided by D-Link pursuant
to this warranty, but shall not apply to any update or replacement which may be provided for download via the Internet, or toany
update which may otherwise be provided free of charge.
D-Link'ssoleobligationunderthissoftware warrantyshallbe to replace anydefective software productwithproduct whichsubstantially conformsto D-Link's
applicableproduct documentation.Purchaser assumes responsibilityfortheselectionofappropriate applicationand system/platformsoftware andassociated
reference materials. D-Link makes nowarrantythat its software products willworkincombinationwithanyhardware, or any applicationorsystem/platform
software product provided byanythird party,exceptingonly suchproducts as are expresslyrepresented, inD-Link'sapplicableproduct documentationas being
compatible. D-Link's obligationunderthiswarrantyshallbe areasonableeffort to provide compatibility,butD-Link shall havenoobligationto provide
compatibilitywhenthere isfaultinthethird-partyhardware or software. D-Linkmakes nowarrantythat operationofits software products willbe uninterrupted
or absolutelyerror-free, andnowarrantythat alldefects inthesoftware product, withinor withoutthescope ofD-Link's applicableproduct documentation,will
be corrected.

TABLE OF CONTENTS
About This User s Guide..............................................................................................................................vii
Before You Start...........................................................................................................................................vii
Information Required for Installation..........................................................................................................viii
Installing the USB Driver.................................................................................................................................x
INTRODUCTION........................................................................................................1
ModemDescription and Operation.................................................................................................................1
ModemFeatures..............................................................................................................................................3
Standards Compatibilityand Compliance.......................................................................................................4
Front Panel Display.........................................................................................................................................5
Rear Panel Connections..................................................................................................................................6
HARDWARE INSTALLATION...................................................................................7
Power on Modem............................................................................................................................................7
FactoryReset Button.......................................................................................................................................7
Network Connections......................................................................................................................................8
CONFIGURING THE MODEM FOR THE FIRST TIME............................................10
Configuring IPSettings on Your Computer..................................................................................................10
Access the Configuration Manager..................................................................................................16
Home.....................................................................................................................................................16
Configure the Modem...................................................................................................................................17
Setup.....................................................................................................................................................18
Configure a NewConnection........................................................................................................................19
WEB-BASED MANAGEMENT................................................................................25
Accessing the Web Manager.........................................................................................................................25
DHCPConfiguration.....................................................................................................................................26
Management IP.............................................................................................................................................27
Tools.....................................................................................................................................................28
Changing the User Name and Password.......................................................................................................28
User Management.........................................................................................................................................29
SystemCommands........................................................................................................................................30
Remote Log...................................................................................................................................................31
Update Gateway............................................................................................................................................32
Ping Test.......................................................................................................................................................33

OAM Test.....................................................................................................................................................34
Status....................................................................................................................................................35
Network Statistics.........................................................................................................................................36
Connection Status.........................................................................................................................................37
DHCPClients................................................................................................................................................38
ModemStatus...............................................................................................................................................39
Product Info..................................................................................................................................................40
SystemLog...................................................................................................................................................41
Help.......................................................................................................................................................42
TECHNICAL SPECIFICATIONS..............................................................................43
IP ADDRESS SETUP...............................................................................................45
IPCONCEPTS.........................................................................................................47
MICROFILTERS AND SPLITTERS.........................................................................50

DSL-362TDSL Modem User s Guide
vii
About This User sGuide
This user sguide provides instructions on howto install the DSL-362T ADSLModemand use it to connecta
computer or Ethernet Local Area Network (LAN) to the Internet.
If you are using acomputer with afunctioning Ethernet port or an available USB port, the quickest and easiest
wayto set up the DSL-362T isto insert the Installation CD into the CD-ROM drive of your computer and follow
the instructions provided in the QuickInstallation Guide.Alternatively, youcan click the “Install DSL-362T”
link on the initial pop-up menu thatappears shortlyafter inserting the CD and followthe instructions as theyare
presented. If the menu fails toappear, explore the CD and find the file “dsl362t.exe”and double-clickit to
launch the installation software.
Before You Start
Please read and make sure you understand all the prerequisites for proper installation of your newModem.Have
all the necessary information and equipment on hand before beginning the installation.
Installation Overview
The procedure to install the Modemcan be described in general terms in the following steps:
1. Gather information and equipment needed to install the device. Before you power on the device or
connect it to your computer, make sure youhave all the necessaryinformation, cables, power adapter
and anyother required equipment listed.
2. Installthe hardware, that is, connectthecables (Ethernetand telephone) to the device and connect the
power adapter.
3. Checkthe IPsettings on yourcomputer and change themifnecessaryso the computer can access the
web-based software built into the Modem.
4. Use the web-based management software to configure the device to suit the requirements ofyour ADSL
account.

DSL-362TDSL Modem User s Guide
viii
Information Required for Installation
Information you will need from your ADSL service provider:
Username
This is the Username used to log on to your ADSL
service provider s network. It is commonlyin the form −
[email protected]. Your ADSL service provider uses this
to identifyyour account.
Record info here
Password
This is the Password used, in conjunctionwith the
Username above, tolog on to your ADSL service
provider s network.This is used toverifythe identityof
your account.
Connection Protocol
This is the method your ADSL service provider uses to
send and receive data between the Internet and your
computer. Your Modemsupports the following
connection protocols: PPPoE, PPPoA, CLIP (IPoA) and
Bridge.
SecurityProtocol
This is the method your ADSL service provider will use
to verifyyour Username and Password whenyou log
on totheir network. Your Modemsupports the PAP and
CHAP protocols.
VPI
This is the Virtual Path Identifier (VPI). It is used in
conjunctionwith the Virtual Channel Identifier (VCI)
below, to identifythe data path between your ADSL
service provider s networkand your computer.
VCI
This is the Virtual Channel Identifier (VCI). It is used in
conjunctionwith the VPIaboveto identifythe data path
between your ADSL service providers networkand
your computer.
Information you will need to change settings on the DSL-362TModem:
Username
This is the Username needed access the Modem s
management interface. When you attempt to connect to
the device through a web browser youwill be prompted
to enter this Username. The default Username for the
Modemis admin. This maybe changed bythe user.
Record info here
Password
This is the Password you will beprompted to enter
when you access the Modem smanagement interface.
The default Password is admin. This maybechanged
bythe user.
LANIP addresses for
the DSL-362T
This is the IP address youwill enter into the Address
field of your web browser toaccess the Modem s
configuration graphical user interface (GUI) using a
web browser. The default IP address is 192.168.1.1
and it is referred to as the “Management IP”address in
this User sManual. This maybe changed tosuit anyIP
address scheme the user desires. This address will be
the base IP address used for DHCP serviceon the LAN
when DHCP is enabled.
LANSubnet Mask for
the DSL-362T
This is the subnet maskused bythe DSL-362T, and
will be usedthroughout your LAN. The default subnet
maskis 255.255.255.0. This can be changed later.

DSL-362TDSL Modem User s Guide
ix
Information you will need about your Ethernet LAN or computer:
Ethernet NIC
If your computer has anEthernet NIC, you can
connect the DSL-362Tto this Ethernetport usingan
Ethernet cable.You canalso use the Ethernet port on
the DSL-362Tto connect toother Ethernet devices,
such as a Wireless Access Point.
Record info here
USB port If your computer has anavailable USB port, you can connect the DSL-362Tto this USB port using a USB
cable.
DHCP Client status
Your DSL-362TADSL Modemis configured, by
default,to be aDHCP server. This means that it can
assign an IP address, subnet mask, and a default
gatewayaddress to computers on your LAN. The
default rangeofIP addresses the DSL-362Twill
assign arefrom 192.168.1.2 to 192.168.1.254.Your
computer (or computers) needs tobe configuredto
Obtain an IP address automatically (that is, they
needto be configured as DHCP clients.)
It is recommended that your collect and record this information here, or in someother secure place, in case you
have to re-configure your ADSL connection in the future.
Once you have the above information, you are readyto setup and configure your DSL-362T ADSL Modem.
Note
The Modem may be resetto its factory defaultsettingsby performing a Restore
settings operation within the management interface (see SystemCommands
below). If you cannot gain access to the management interface, you may optto use
the Reset button ontherear panel ofthedevice(see FactoryReset Button below).

DSL-362TDSL Modem User s Guide
x
Installing the USBDriver
The CD-ROM shipped with the Modemcontains the USB driver software.
1. Insert the DSL-362TInstallation CD-ROM into the CD-ROM drive.
2. Connect the USB cable to the device. Withinafewseconds youshould see the “Found NewHardware”
message window, followed shortlyafter bythe opening “Found NewHardware Wizard”window:
3. If you do not see the auto-run windowpictured above, explore the CD and double-clickthe inf file
DLink_362t.inf.
4. Click the Next button.
5. Click the Next button.

DSL-362TDSL Modem User s Guide
xi
6. Check “CD-ROM drives"(as shownabove) if youare using the USB driver included on the CD-ROM
that came withyour Modem.Click Next.
7. Connect the Ethernet cable if youhave not done so.
8. Connect the ADSLcable ifyou have not done so. Remember that most ADSLinstallations require a
filter to divide the ADSL signal fromthe Plain-Old Telephone (POTS) signal.
9. You can restart your computer nowbyclicking the Finish button. The computer will be able to connect
to the Modemthrough the USB port after restarting.

DSL-362TADSL Modem User s Guide
1
1
Introduction
This section provides a brief description of the Modem, its associated technologies and a list of Modemfeatures.
Modem Description and Operation
The DSL-362TADSLModemis designed to provide asimple and cost-effective ADSLInternet connection for
individual computersthrough either the Ethernet or USB ports, or use it to bridge your Ethernet LANto the
Internet. The DSL-362T combines the benefits of high-speed ADSLtechnologyand LANIP management in one
compact and convenient package. ADSLtechnologyenablesmanyinteractive multi-mediaapplications such as
video conferencing and collaborative computing.
The Modemis easy to installand use. The DSL-362Tconnects to single computer or anEthernet LAN via a
standard Ethernet interface. Asingle computer mayalso be connected through the USB port. The ADSL
connectionis made using ordinarytwisted-pair telephone line with standard connectors.Multiple PCs can be
networked and connected to the Internet using asingle Wide Area Network(WAN) interface and singleglobal
IPaddress.
What is ADSL?
Asymmetric Digital Subscriber Line (ADSL) is anaccess technology that utilizes ordinarycopper telephone
lines to enable broadband high-speed digital data transmissionand interactive multimedia applications for
business and residential customers.
ADSLgreatlyincreasesthe signal carrying capacityofcopper telephone lines without interfering with regular
telephone services. For the ADSLuser, this means fasterdownloads and more reliable connectivity. ADSL
devices make itpossible to enjoybenefits such as high-speed Internet access without experiencing any loss of
qualityor disruption of voice/fax telephone capabilities.
ADSLprovides adedicated service over asingle telephone line operating at speeds ofup to8Mbps downstream
and up to 640 Kbps upstream,depending on local telephoneline conditions. Asecure point-to-point connection
is established between the user and the central office of the service provider.
D-Link ADSL devices incorporate the recommendations of the ADSLForumregarding framing, data format,
and upper layer protocols.
LowPass Filters
Since ADSLand telephone services share the samecopper wiring to carrytheir respective signals, afiltering
mechanismmaybe necessaryto avoid mutual interference.Alowpass filter device can be installed for each
telephone that shares the line with the ADSLline. These filters are easyto install passive devices that connect to
the ADSLdevice and/or telephone using standard telephone cable. Ask your service provider for more
information about the use of lowpass filters with your installation.
Operating Systems
The DSL-362Tuses anHTML-based web interfacefor setup and management. The webconfiguration manager
maybe accessed using anyoperating systemcapable of running web browser software, including Windows98
SE, Windows ME, Windows2000, and Windows XP.

DSL-362TADSL Modem User s Guide
2
Web Browser
Anycommonweb browser can be used to configure theModemusing the web configuration management
software. The programisdesigned to work best withmore recentlyreleased browserssuch as Opera, Microsoft
Internet Explorer®version 5.0, Netscape Navigator®version 4.7, or later versions. The web browser must have
JavaScript enabled. JavaScript is enabled bydefaulton manybrowsers. Make sure JavaScript hasnot been
disabled byother software (such as virus protection or web user securitypackages) that maybe running on your
computer.
Ethernet Port (NIC Adapter)
Anycomputer that usesthe Modemmust be ableto connect to itthrough the Ethernetport on the Modem.This
connectionis an Ethernet connection and therefore requires that your computer be equipped withan Ethernet
port as well. Mostnotebook computers arenowsold with an Ethernetport already installed. Likewise, most fully
assembled desktop computers comewithanEthernetNIC adapter as standard equipment. If your computer does
not have anEthernetport, you must install an Ethernet NIC adapter before you can use the Modem.If you must
install an adapter, followthe installation instructions that come with the Ethernet NIC adapter.
Additional Software
It maybe necessaryto install software on your computerthat enables the computer to access the Internet.
Additionalsoftware must be installed if youare using the device asimple bridge. For abridged connection, the
informationneeded to makeand maintain the Internetconnection isstored on another computer or gateway
device, not in the Modemitself.
If your ADSLservice is delivered through aPPPoE, PPPoAor IPoAconnection, the informationneeded to
establish and maintainthe Internet connection can be stored in the Modem.Inthis case,it is not necessaryto
install software on your computer. It mayhowever be necessaryto change somesettings inthe device, including
account information used to identifyand verifythe connection.
Allconnections to the Internet require aunique global IP address. For bridged connections, the global IP settings
must reside in aTCP/IP enabled device on the LANside of the bridge, suchas aPC, aserver, agatewaydevice
suchas aModemor similarfirewall hardware. The IPaddress can be assigned in anumber of ways. Your
network service provider will give you instructions about anyadditionalconnection software or NIC
configuration that maybe required.

DSL-362TADSL Modem User s Guide
3
Modem Features
The DSL-362TADSL Modemutilizesthe latest ADSLenhancements to provide areliable Internet portal
suitable for most small to medium sized offices. DSL-362Tadvantages include:
• PPP (Point-to-Point Protocol) Security The DSL-362TADSLModemsupportsPAP(Password
Authentication Protocol) and CHAP(Challenge Handshake Authentication Protocol) for PPP connections.
• DHCP Support Dynamic Host Configuration Protocol automaticallyand dynamicallyassigns allLAN IP
settings to each host on your network. This eliminates the need to reconfigure everyhost whenever changes
in network topologyoccur.
• NetworkAddress Translation (NAT) For small officeenvironments, the DSL-362T allowsmultiple
users onthe LANto access the Internetconcurrentlythrough asingle Internetaccount. This provides
Internet access to everyone in the office for the price of a single user.
NATimprovesnetworksecurityineffect byhiding the private network behind one global and visible IP
address. NATaddress mapping can also be used to link twoIPdomains via a LAN-to-LAN connection.
• TCP/IP (Transfer Control Protocol/Internet Protocol) The DSL-362T supports TCP/IPprotocol, the
language used for the Internet.It is compatible with access servers manufactured bymajor vendors.
• ATM (Asynchronous Transfer Mode) The DSL-362Tsupports Bridged Ethernet over ATM (RFC1483),
IPover ATM (RFC1577) and PPPover ATM (RFC 2364).
• Precise ATM Traffic Shaping Traffic shaping is a method of controlling the flowrate of ATM data cells.
This function helps to establish the Qualityof Service for ATM data transfer.
• G.hs (Auto-handshake) This allowsthe Modemto automaticallychoose either the G.lite or G.dmtADSL
connection standards.
• High Performance Veryhigh ratesof data transfer arepossible withthe Modem.Up to eight Mbps
downstreambit rate using the G.dmt.
• Easy Installation The DSL-362T uses aweb-based graphical user interface program for convenient
management access and easyset up. Anycommon web browser software can be used to manage the Modem.

DSL-362TADSL Modem User s Guide
4
Standards Compatibilityand Compliance
The DSL-362T complies withor is compatible withthe following standards as recognized bytheir respective
agencies.
• ITU G.992.2 (G.lite “Splitterless ADSL”) compliant
• ITU-T Rec. I.361 compliant
• RFC 791 Internet Protocol compliant
• RFC 792 UDPcompliant
• RFC 1334 PPPAuthentication Protocol compliant
• RFC 1483 IPover AAL5/ Bridged Ethernet over AAL5 compliant
• RFC 1557 Classical IPover ATM (IPoA) compliant
• RFC 1661 Point to Point Protocol (PPP) compliant
• RFC 1877 Automatic IPassignment compliant
• RFC 1994 Challenge Handshake Authentication Protocol compliant
• Supports RFC 2131 and RFC 2132 DHCPfunctions including: automatic assignment of IPaddress, use of
subnetmask and default gateway and provision of DNS server address for all hosts
• RFC 2364 PPPover ATM compliant (PPPoA) compliant
• RFC 2516 PPPover Ethernet compliant (PPPoE) compliant
• RFC 2684 Bridged/Routed Ethernet over ATM compliant
• Embedded management agentaccessed via web browser
• Supports DHCPfor up to 253 hot connections
• Supports ATM ForumUNI 3.1/4.0

DSL-362TADSL Modem User s Guide
5
Packing List
Open the shipping carton and carefullyremove all items. In addition to this User'sGuide, ascertain that youhave:
• One DSL-362TADSL Modem
• One Quick Installation Guide
• One twisted-pair telephone cable used for ADSL connection
• One straight-through Ethernet cable
• One USB cable
• One AC power adapter suitable for your electric service
• An Installation CD containing this User s Manual and USB software driver
Front Panel Display
Place the Modemin a location that permits an easy viewof the LED indicators on the frontpanel.
The LED indicators on the front panel include the Power, Status, ADSLLink/Act, Ethernet Link/Act,and
USB Link/Act indicators. The ADSL, Ethernet, and USB indicators monitor link status and activity(Link/Act).
Power Steadygreen light indicates the unit is powered on. When the device is
powered off this remains dark.
Status
Lights steadygreenduringpower onself-test (POST). Oncetheconnection
status hasbeen settled, thelightwill blinkgreen.Iftheindicator lights steady
greenafter thePOST,thesystemhas failedandthe deviceshouldbe
rebooted.
ADSL: Link/Act Steadygreen light indicates a valid ADSL connection. This will light after the ADSL negotiation process has been settled. A blinkinggreen light indicates
activityon theWAN (ADSL) interface.
Ethernet: Link/Act A solid greenlightindicates a valid linkon startup. Thislight will blinkwhen
there is activitycurrentlypassing through the Ethernet port.
USB: Link/Act Steadygreen light indicates a valid USB connection.A blinking green light
indicates activityon the USB interface.

DSL-362TADSL Modem User s Guide
6
Rear Panel Connections
Allcable connections to the Modemare made attherear panel. Connectthe power adapter here to power on the
Modem.Use the Reset buttonto restore the settings to the factorydefault values(see FactoryReset Buttonin the
next chapter for instructions on using the reset button).
Note The Modem may be rebooted by disconnecting and then reconnecting the power.
ADSL port,
connect ADSL
cable here
USB port,
connect USB
cable here
and install
the USB
driver
Ethernet
port,
connect
Ethernet
cable here
Factory
Reset
button
Power cord
connects
here

DSL-362TADSL Modem User s Guide
7
2
Hardware Installation
The DSL-362Tmaintains three separate interfaces, anEthernet,aUSB and anADSLinterface. Place the
Modemin alocation where itcan be connected to the various devices aswellas to apower source. The Modem
should not be located where itwill be exposed to moisture or excessive heat. Make surethe cables and power
cord are placedsafelyout of the wayso theydo not createatripping hazard. As withanyelectrical appliance,
observe common sense safetyprocedures.
The access point can be placedon ashelfor desktop, ideally youshould be able to see the LED indicators on the
front ifyou need to viewthem for troubleshooting.
Power on Modem
CAUTION: The Modemmust beusedwiththepoweradapterincluded withthe
device.
To power on the Modem:
1. Insert the AC Power Adapter cord into the power receptacle located on the rear panel of the Modemand
plug the adapter into a suitable nearbypower source.
2. You should see the Power LED indicator light up and remain lit. The Status LED should light solid green
and begin to blink after a fewseconds.
3. If the Ethernet port is connected to a working device, checkthe Ethernet Link/Act LED indicators to make
sure the connection is valid. The Modemwill attempt to establish the ADSL connection, if the ADSL line is
connected and the Modemis properlyconfigured this shouldlight up after several seconds.If this is the first
time installing the device, some settings may need to be changed before the Modemcan establish a
connection.
FactoryReset Button
The Modemmaybe reset to the originalfactorydefault settings bydepressing the reset button for afewseconds
while the device ispowered on. Use aballpoint or paperclip to gentlypush downthe reset button. Remember
that thiswillwipe outany settings stored in flash memory including user account information and LANIP
settings. The factorydefault IP address of the Modemis192.168.1.1 and the subnet mask is 255.255.255.0, the
default management Username is admin and the default Password is admin.

DSL-362TADSL Modem User s Guide
8
Network Connections
Networkconnections are provided through the ADSLport, the Ethernetport and the USB port on the back of the
Modem.See the Rear Panel diagramabove and the illustrations belowfor examples. See Installing the USB
Driver above for a description of the USB driver installation procedure.
Connect ADSL Line
Use the ADSLcable included withthe Modemto connect itto atelephone wall socketor receptacle. Plug one
end of the cable into the ADSLport (RJ-11 receptacle) on the rear panel of the Modemand insert the other end
into the RJ-11 wall socket. If you are using alowpass filter device, followthe instructions included withthe
device or given to you byyour service provider. The ADSL connection represents the WANinterface, the
connectionto the Internet. It is the physical link to the service provider snetwork backbone and ultimatelyto the
Internet.
Connect Modem to Ethernet
The Modemmaybe connectedto asingle computer or Ethernet device through the 10BASE-TXEthernet port
on the rear panel. Any connection to an Ethernet concentrating device suchas aswitch or hub must operate at a
speed of 10/100 Mbps only.When connecting the Modem to anyEthernet device thatis capableof operating at
speeds higher than 10Mbps, be sure that the device has auto-negotiation (NWay) enabled for the connecting port.
Note
In order to connect the Modem toan EthernetLAN, it isnecessary to install
3rd-party PPP connection software on any system used to access the Internet.
Use standard twisted-pair cablewithRJ-45 connectors. The RJ-45 port on the Modemis a crossed port (MDI-X).
Followstandard Ethernet guidelines when deciding what type of cable to use to make this connection. When
connecting the Modemdirectlyto aPCor server use anormal straight-through cable. You should use acrossed
cable whenconnecting the Modemto anormal (MDI-X) port on aswitchor hub. Use anormal straight-through
cable when connecting it to an uplink (MDI-II) port on a hub or switch.
The rules governing Ethernetcable lengths applyto the LANto Modemconnection. Be sure that the cable
connecting the LAN to the Modemdoes not exceed 100 meters.
Computer to Modem Connection
Connect the Modem
directlyto a
10/100BASE-TX
Ethernet port on a PC
or notebook computer
using the Ethernet
cable provided as
shownin this diagram.