D-MAX DSC-Se5 User manual

USER MANUAL
DSC-300Si5/Se5
HIGH SPEED DOME CAMERA

2

1
1.
CAUTION --------------------------------------------------------------------------------
2
2.
INTRODUCTION OF PRODUCT
4
1). DESCRIPTION AND FEATURES ---------------------------------------------
4
2). INSTALLATION AND CONNECTION ----------------------------------------
5
2-1. NAME AND FUNCTION OF EACH PART -----------------------------
5
2-2. INSTALLATION --------------------------------------------------------------
6
2-3. BASIC CONNECTION -----------------------------------------------------
8
2-4. CONNECTION DIAGRAM ------------------------------------------------
9
3.
DIRECTIONS FOR USE
11
1). DIP SWITCH SETTING ----------------------------------------------------------
11
2). HOW TO CHANGE PROTOCOL ----------------------------------------------
12
3). SETTING ADDRESS OF DIP SWITCHES ----------------------------------
13
4). HOW TO USE OSD MENU -----------------------------------------------------
14
4-1. HOW TO CONTROL OSD MENU ---------------------------------------
14
4-2. FUNCTIONAL DESCRIPTIONS ON EACH MENU -----------------
15
4-3. FUNCTIONAL SETTING, OPERATION/DELETION THE
KEYBOARD-------------------------------------------------------------------
27
4-4. OSD MESSAGE DESCRIPTION ----------------------------------------
30
4
TROUBLE SHOOTING ---------------------------------------------------------------
32
5
DIMENSION ---------------------------------------------------------------------------
34
6
ASSEMBLY ---------------------------------------------------------------------------
36
7
SPECIFICATION --------------------------------------------------------------------
40
Table of contents

2
Thank you for purchasing our product. Please operate the product after being
fully aware of the manual.
Pease contact us if you have any queries.
Precaution
Note the following matters before the installation of the product.
Avoid the following places for the installation.
1.CAUTION
A high/low temperature: Using indoor-cameras
in the places of +50°C~ -10°C can cause
troubles and lower its capacity.
Snow, rain and wet: Humidity or water and
any liquid inside-camera can cause troubles.
Oil, gas: Oil and gas can damage the camera
as they go through the cameras.
Vibration, shock: They bring on problems or
errors of the camera.
Direct light, exposure to the air: In the case of
that sets indoor- cameras outside where the
weather is changeable, it can cause problems.
Closing to High frequency and electric power
lines: Setting the camera up around
electromagnetic units or power supplier can
cause problems.

3
Caution in Use
Do not disassemble the unit and put alien substances in the unit.
- Disassembling the unit or putting alien substances such as a metal can make the
camera defective.
-Make sure of power switch-off before the installation.
: Ensure power switch-off and check the voltage the camera before the installation.
-Do not give the unit a shock and an operation.
: Giving a strong shock or an excessive power on the button, terminal can cause
problem.
This product has been designed and manufactured in accordance with the harmonized
European standards, following the provisions of the below stated directives.
Electromagnetic Compatibility Directive 89/336/EEC
(EN60065:1998, EN61000-6-3:2001, EN61000-6-1:1997)
This devise complies with part 15 of the FCC rules operation is subject to the
following two conditions: (1) This device may not cause harmful interference and
(2) This device must accept any interference received including interference that
may cause undesired operation

4
1) DESCRIPTION AND FEATURES
This camera has been designed elegantly for buildings, department stores that
need to be in harmony with the interior as a high speed dome camera, including
various observation functions.
2. INTRODUCTION OF PRODUCT
☺35x Zoom lens
35x Optical zoom lens combined with an auto focus
system and digital zoom enable you to get maximum
420x great pictures.
☺A low light function
Surveillance with optimum picture is possible owing
to digital-slow-shutter function and wide-dynamic-
range function.
Digital-slow-shutter function is improving the CCD
sensitivity by electrically lengthening exposure time
so that it should be under surveillance on the
condition of 0.01 Lux in color.
Wide-dynamic-range function is included to look at
object clearer in back light condition.
☺Various auto-surveillance functions
PTZ trace
Track the registered manual operation for about 180
seconds.
Auto swing
Repeat pan and tilt between two preset positions.
Group sequence
12 Preset positions are chained in one Group.
Tour sequence
Max 12 Groups are bound.
☺250 Preset positions
A maximum of 250 preset positions can be
programmed. The preset function enables to set
where you want on monitor at any time.
☺Smart pan/tilt function
It should be rotated pan travel by 360° endless.
Pan and tilt speed compensation function in proportion to
depth of zoom.
☺Day & Night function with filter
It allows to make surveillance in the night or low
illumination condition with motorized IR cut filter
system. (0.1 Lux)
In the darkness, it should be changed to black &
white mode automatically.
With DSS control, it allows watching on 0.009
Lux.
☺4ch alarm inputs
It can be directly connected to sensor and used with
presets owing to built-in 4-channel sensor input
terminals. It can be also operated together with
other equipment owing to built-in alarm output. (1-
Relay normal output)
☺Auto flip function
The unit can track the moving object automatically
until 180°in vertical by using controller.
☺8 Privacy Masking Zones
For the privacy, it can be programmed for masking
zone up to 8 locations on the OSD menu screen.
☺OSD (On Screen Display) Menu
Provides character information displayed on the
monitor, such as the camera ID address, camera
name, preset number, sequence status, and sets
various functions of camera easily on the OSD
menu screen.
☺STABILIZATION FUNCTION

5
2) INSTALLATION AND CONNECTION
2-1. Name and function of each part
INDOOR TYPE
OUTDOOR TYPE
Upper cover
The camera‟s body goes to
here and a power cable, data
cable, video cable, sensor
have been connected with this
Camera body
A main body that has a built-in
the control units and camera
Lower cover
Insert the body into the upper
cover, then close the lower
cover

6
2-2. Installation
INDOOR TYPE
OUTDOOR TYPE
Loosen the bolt of the back of lower cover by
a screwdriver(+), then turn the cover as
above the picture and pull the lower cover to
the down
Loosen the four bolts of the lower cover, then
separate.
SEPARATION OF LOWER COVER
SEPARATION OF UPPER COVER
Loosen the three bolts, the round head shaped, of the camera body. The
three bolts are not loosened completely and not come up more than 1cm
of the lower cover, then separate.

7
Pull the cover up with grabbing the bottom of the camera after loosening
the three bolts
Open the connector cover, then connect
power, data, video cable and sensor
The cover is opened if user loosens the
one bolt on the connector cover by using a
screwdriver(+).
The bolts not loosened completely to
protect from missing of them.
Be careful that each cable which each
function is changed wrong

8
Have you connect the power cable in the right direction ?
If yes
①RED led, in the niddle of the connector, is lighted
②Use AC24V power souce and user can use any power input that is connected
with a terminal and a jack(But use 1 input).

9
2-3. Connection diagram
Reference to the following
page.
Connect the image line of a
monitor
User can control maximum up to 255 cameras
connected by using the exclusive control keyboard.
User can connect it maximum up to 1.2km when
using twist pair shield cable as a connecting cable
DC12V/1A adaptor and junction box are provided on
a purchase, Junction box consists of 2 data ports
( Each data port can be connected with maximum up
to 128 cameras and sub keyboard terminal.

10
Must use AC24V power source, current intensity must be less than 1.5A
and must use a double winding transformer
Alarm output is tangency output of
relay non-load, it can be used up to
AC220/10A by connecting the load.
The switch is automatically turned
on when the sensor works and it is
possible to cancel by using the
controller after a limited time
The sensor
Can be connected maximum 4 channels and the camera
can be moved automatically to the point by preset mode,
if there is any problem
DATA
Can be processed by RS485 or RS422 and use parallel connection to use a large quanity of
cameras. ( Even if it must be used 2-twist paired cable in use of RS422, the terminal port
which was connected with R485 cable port with 1-pair cable when it is not necessary to take
a return data from camera

11
1). DIP SWITCH SETTING
3. DIRECIONS FOR USE
Set the power of the camera
switch-off to control the dip
switch and set switch-on after
using it.
This part is a power switch
Ser the camera numbers in the state of
ADDR. Set communication speed.
Protocol in the state od INIT.
- This part is each address od camera
It is a notice to turn the data signal
on.(in power on, the green led is
turned on
-Terminalation resistor (DIP SW NO1)
~ Turn the last camera on the data line as a
switch to turn on/off the terminal resistor on.
Turn the DIP S/W of some od the farthest
cameras on in the case of the data lines
distributed to several directions.
( The first default is off )
-RS485/422 select (DIP SW NO2)
~ Turn on or off for the suitable data system
between RS485 and RS422
( The first default is RS485 )
- Address/Initial select (DIP SW NO3)
~ Set the DIP SW up in the ADDRESS
( reference the next page )
(The first default is address)
~Set the communication speed and
protocol(Demand for the technical inquiry) up
in the state of the initial
-Internal/External (DIP SWNO5)
~ Use it when selecting Internal and External
(The first default is Internal)

12
2) HOW TO SET PROTOCOL
①Please the power off
②Switch protocol that user wants to change on as above the cable
③The power on, then the set protocol and baud rate are appeated.
④The power off, if every setting is right. Then the change of protocol is finished.
⑤Change NO 3 of S2 to ADDR before the power on, then the power on after setting the address of the camera.
⑥Try it again with the information as above the table, if something is wrong
PROTOCOL
S 1
S 2
SW 1
SW 2
SW 3
SW 7
SW 8
SW ‘INITADDR’
D-MAX (9600 bps)
OFF
OFF
OFF
OFF
OFF
INIT
P-P (9600 bps)
ON
OFF
OFF
OFF
OFF
INIT
P-P (4800 bps)
ON
OFF
OFF
OFF
ON
INIT
P-P (2400 bps)
ON
OFF
OFF
ON
OFF
INIT
P-D (9600 bps)
OFF
ON
OFF
OFF
OFF
INIT
P-D (4800 bps)
OFF
ON
OFF
OFF
ON
INIT
P-D (2400 bps)
OFF
ON
OFF
ON
OFF
INIT
S-T (9600bps)
OFF
OFF
ON
OFF
OFF
INIT
Do not necessary to set it up
1
2
3
4
5
6
7
8
O
N
4
2
2
I
N
I
T
P
A
L
I
N
T
.
ON
OFF
A D D R E S S
T
M
4
8
5
A
D
D
R
N
T
S
C
E
X
T
.
O
N
O
F
F
S 1
S 2
Change No3 of S2 to INIT if user wants to change protocol
Set this part up
The switch to select protocol
The switch to select baud rate

13
3) SETTING ADDRESS OF DIP SWITCHES.
Use DIP switches No.1 to No.8 for address, it can be set 1 program to 255 program.
RX
NO
DIP SWITCH (HEX)
RX
NO
DIP SWITCH (HEX)
1
2
3
4
5
6
7
1
2
3
4
5
6
7
1
ON
OFF
OFF
OFF
OFF
OFF
OFF
33
ON
OFF
OFF
OFF
OFF
ON
OFF
2
OFF
ON
OFF
OFF
OFF
OFF
OFF
34
OFF
ON
OFF
OFF
OFF
ON
OFF
3
ON
ON
OFF
OFF
OFF
OFF
OFF
35
ON
ON
OFF
OFF
OFF
ON
OFF
4
OFF
OFF
ON
OFF
OFF
OFF
OFF
36
OFF
OFF
ON
OFF
OFF
ON
OFF
5
ON
OFF
ON
OFF
OFF
OFF
OFF
37
ON
OFF
ON
OFF
OFF
ON
OFF
6
OFF
ON
ON
OFF
OFF
OFF
OFF
38
OFF
ON
ON
OFF
OFF
ON
OFF
7
ON
ON
ON
OFF
OFF
OFF
OFF
39
ON
ON
ON
OFF
OFF
ON
OFF
8
OFF
OFF
OFF
ON
OFF
OFF
OFF
40
OFF
OFF
OFF
ON
OFF
ON
OFF
9
ON
OFF
OFF
ON
OFF
OFF
OFF
41
ON
OFF
OFF
ON
OFF
ON
OFF
10
OFF
ON
OFF
ON
OFF
OFF
OFF
42
OFF
ON
OFF
ON
OFF
ON
OFF
11
ON
ON
OFF
ON
OFF
OFF
OFF
43
ON
ON
OFF
ON
OFF
ON
OFF
12
OFF
OFF
ON
ON
OFF
OFF
OFF
44
OFF
OFF
ON
ON
OFF
ON
OFF
13
ON
OFF
ON
ON
OFF
OFF
OFF
45
ON
OFF
ON
ON
OFF
ON
OFF
14
OFF
ON
ON
ON
OFF
OFF
OFF
46
OFF
ON
ON
ON
OFF
ON
OFF
15
ON
ON
ON
ON
OFF
OFF
OFF
47
ON
ON
ON
ON
OFF
ON
OFF
16
OFF
OFF
OFF
OFF
ON
OFF
OFF
48
OFF
OFF
OFF
OFF
ON
ON
OFF
17
ON
OFF
OFF
OFF
ON
OFF
OFF
49
ON
OFF
OFF
OFF
ON
ON
OFF
18
OFF
ON
OFF
OFF
ON
OFF
OFF
50
OFF
ON
OFF
OFF
ON
ON
OFF
19
ON
ON
OFF
OFF
ON
OFF
OFF
51
ON
ON
OFF
OFF
ON
ON
OFF
20
OFF
OFF
ON
OFF
ON
OFF
OFF
52
OFF
OFF
ON
OFF
ON
ON
OFF
21
ON
OFF
ON
OFF
ON
OFF
OFF
53
ON
OFF
ON
OFF
ON
ON
OFF
22
OFF
ON
ON
OFF
ON
OFF
OFF
54
OFF
ON
ON
OFF
ON
ON
OFF
23
ON
ON
ON
OFF
ON
OFF
OFF
55
ON
ON
ON
OFF
ON
ON
OFF
24
OFF
OFF
OFF
ON
ON
OFF
OFF
56
OFF
OFF
OFF
ON
ON
ON
OFF
25
ON
OFF
OFF
ON
ON
OFF
OFF
57
ON
OFF
OFF
ON
ON
ON
OFF
26
OFF
ON
OFF
ON
ON
OFF
OFF
58
OFF
ON
OFF
ON
ON
ON
OFF
27
ON
ON
OFF
ON
ON
OFF
OFF
59
ON
ON
OFF
ON
ON
ON
OFF
28
OFF
OFF
ON
ON
ON
OFF
OFF
60
OFF
OFF
ON
ON
ON
ON
OFF
29
ON
OFF
ON
ON
ON
OFF
OFF
61
ON
OFF
ON
ON
ON
ON
OFF
30
OFF
ON
ON
ON
ON
OFF
OFF
62
OFF
ON
ON
ON
ON
ON
OFF
31
ON
ON
ON
ON
ON
OFF
OFF
63
ON
ON
ON
ON
ON
ON
OFF
32
OFF
OFF
OFF
OFF
OFF
ON
OFF
64
OFF
OFF
OFF
OFF
OFF
OFF
ON
-No.1 is changed to No.64 and the last No.64 is changed No.128 when No.7 DIP SW is on.
-No.1 is changed to No.129 when No.7 DIP SW is off and No.8 DIP SW is on.
-No.1 is changed to No.193 and user can set up to maximum 255 ADDRESS when No.7, 8 DIP SW are on.

14
4) HOW TO USE OSD MENU
4-1. How to control OSD menu
● OSD (ON SCREEN DISPLAY) CONTROL
It is the function to call up the Menu
＊User can not only set Preset, Group, Tour, Swing, Trace functions of the camera up by the menu, but also set
them up by shortening keys. (Refer to 3-3 content)
● Accessing OSD MENU
(1) The menu is displayed on the screen with the key tone when user presses No.1 and menu key.
●OSD Menu Control.
Right and Left moving of Cursor Feed
letters into system.
Selection of up and down menu
Change of setting.
●Cancellation of OSD MENU
<< CAMERA SETUP p1 >>
1. ID Set : CAM-001
2. OSD Display : ON
3. Back Light : OFF
4. Shutter speed : AUTO
5. BLC level : 052
6. White balance : AUTO
7. Focus mode : AUTO
8. Stabilization Mode : OFF
- NEXT MENU PAGE

15
4-2. Functional Descriptions of each Menu.
1. ID SET.
It is the function to set ID of the camera.
Move to No.1 menu and the screen moves as following when user presses F/F key.
User can choose letters that they want, if user control a
joystick up / down / right / left, and user can reselect the
previous letters, if user presses Z/I, Z/O or turn the head of
the joystick to right/left.
“•” is not displayed on the screen as a blank letter,
user can input letters in Japanese and in Chinese
if user moves the joystick down continuously.
2. OSD DISPLAY.
Set up whether user sets ID and STATUS to display on the
screen in normal operating.
●ID + Status: „ID‟and „Status‟displayed on the screen
●ID only: Only „ID‟displayed on the screen
●Status only: Only „Status‟displayed on the screen
●All off: Nothing displayed on the screen
3. BACK LIGHT
Set up backlight compensation mode.
●On: It compensates a dark subject to a light subject by
BACK LIGHT function.
●Off: Cancellation of BACK LIGHT compensation mode.
<< CAMERA SETUP p1 >>
1. ID Set : CAM-001
2. OSD Display : ON
3. Back Light : OFF
4. Shutter speed : AUTO
5. BLC level : 052
6. White balance : AUTO
7. Focus mode : AUTO
8. Stabilization Mode : OFF
- NEXT MENU PAGE

16
4. SHUTTER SPEED
Shutter speed is the duration of the electronic shutter. Set shutter
speed to operate automatically (Auto) or manually (Numeric Value).
●AUTO (default) –The electronic shutter speed is set automatically by
the amount of light sensed by the camera.
●Manual –it allows to control iris with this menu. Before setup, please
„day/night‟ & „DSS‟ should be off.
●Range: AUTO, 1/125, 1/150, 1/200, ……, 1/10000
5. BLC LEVEL
BLC level is a backlight compensation level control. Set BLC level to
operate manually (Numeric Value). Before setup, make sure of that
„Back Light‟ is ON.
To set the BLC level with the joystick left / right:
●Level control –000,001, …… , 077, 078.
●The default value is 052.
6. WHITE BALANCE
This feature automatically processes the viewed the image to retain color balance over a color temperature range.
The default setting for white balance is AUTO.
There are three settings:
●AUTO, INDOOR, OUTDOOR
7. FOCUS MODE
Focus mode allows the lens to remain in focus during zoom-in, zoom-out. The default is ONESHOT. To set is with
the joystick left / right on the parameter.
There are two settings:
●AUTO –The camera will focus automatically when using pan, tilt and zoom functions.
●MANUAL –Focus is operated manually. To focus, press the Focus Far or Focus near button on the keyboard.
8. STABILIZATION MODE
There is some tremble as zoom magnification is high, the function can compensate the tremble.
●On / Off
<< CAMERA SETUP p1 >>
1. ID Set : CAM-001
2. OSD Display : ON
3. Back Light : OFF
4. Shutter speed : AUTO
5. BLC level : 052
6. White balance : AUTO
7. Focus mode : AUTO
8. Stabilization Mode : OFF
- NEXT MENU PAGE

17
9. ZOOM MAX LIMIT
Zoom max limit allows the user to define a limitation on the amount of
telephoto zoom. The default setting is X46.
Camera with 420X zoom (35X optical zoom and 12X digital zoom) can
be set for X35, X70, X105 …….. and X420.
10. DSS CONTROL
DSS (Digital-Slow-Shutter) control allows the camera to be operated
in low light condition. The level value of 32 fields is the maximum.
Increasing value with the joystick left / right on the parameter, the
object is showed more brightness in low light condition but if the object
moves, the image of the object is getting unclear according to DSS
level up. Due to the CPU accumulates amounts of the lights in
physical time and displays pictures on the monitor through electronic processes. The time is slow than the physical
moving time in nature.
The way of set is with the joystick left / right on the parameter:
●Control –OFF, 02, 04, 08, 16 (Default), 32 fields.
11. WDR ON/OFF
WDR (Wide-Dynamic-Range) on/off support super backlight compensation. This function is a new high technology
of BLC function. It allows to identify the objects clearer under strong backlight condition. The default setting is
AUTO.
There are three settings:
●AUTO –According to amount of backlight, the camera is compensated automatically and especially it
allows perform in zoom-in.
●Manual –Compensate for backlight continuously regardless amount of backlight.
●OFF –The function is off (Factory default).
12. WDR LEVEL
WDR level allows compensative performance to increase backlight. The default is 100.
If the value increases, the camera is more sensitivity for the backlight and it is possible to bring video noise.
The way of setup is with the joystick left / right on the parameter
●Control –000, 001,……, 014, 126. ●The default is 100.
13. DAY & NIGHT ON/OFF
It is used when you want to see an object clearer in night or low light
There are five settings:
●AUTO-MID (default): Convert to monochrome mode automatically
<< CAMERA SETUP p2 >>
9. Zoom MAX Limit : x70
10. DSS Control : 16 fields
11. WDR On off : Off
12. WDR Level : 100
13. DAY&NIGHT of/off : AUTO-LOW
14. PRESET SET & RUN PAGE
15. TRACE SET PAGE
- NEXT MENU PAGE

18
according to low light condition with medium sensing.
●AUTO-LOW: Convert to monochrome mode automatically
according to low light condition with low sensing.
●AUTO-HI: Convert to monochrome mode automatically according
to low light condition with high sensing
●OFF: Do not convert to monochrome mode, even if the camera in
low light condition.
●ON: Convert to monochrome mode by force, regardless color,
daylight.
14. PRESET SET & RUN PAGE
It is a function to set and operate Preset, Group, Tour.
User can see the screen when moves the joystick to Right/Left after fixing the cursor on the menu.
<<PRESET SETUP PAGE>>
①Preset set CH: User can set Preset No. and title on this menu.
-Preset No. set: Set it by moving the joystick to Right/Left
-Preset title set: User can see the menu “SET ID” when presses F/F key after setting preset No.
The setting steps are the same as “ID Set” at page 14
②Preset PTZ set : Set the position of Preset.
Select the main menu with the joystick, then press F/F key for next page.
Select [SAVE] with F/N key after setting the Preset point by using the joystick and ZOOM In/Out function,
then the data is saved if user presses
<< CAMERA SETUP p2 >>
9. Zoom MAX Limit : x70
10. DSS Control : 16 fields
11. WDR On off : Off
12. WDR Level : 100
13. DAY&NIGHT of/of f: AUTO-LOW
14. PRESET SET & RUN PAGE
15. TRACE SET PAGE
- NEXT MENU PAGE