Dahua VTO2101E-P User manual

Villa Door Station (VTO) Baseline
(Version 4.3)
Quick Start Guide
V1.0.0
V1.0.0
Поставщик систем безопасности TELECAMERA.RU

I
Foreword
General
This manual introduces the structure, mounting process, and basic configuration of the door
station (VTO).
Safety Instructions
The following categorized signal words with defined meaning might appear in the manual.
Signal Words
Meaning
WARNING
Indicates a medium or low potential hazard which, if not avoided,
could result in slight or moderate injury.
CAUTION
Indicates a potential risk which, if not avoided, could result in
property damage, data loss, lower performance, or unpredictable
result.
NOTE
Provides additional information as the emphasis and supplement
to the text.
Revision History
Version
Revision Content
Release Date
V1.0.0
First release
March 2020
About the Manual
The manual is for reference only. If there is inconsistency between the manual and the
actual product, the actual product shall prevail.
We are not liable for any loss caused by the operations that do not comply with the manual.
The manual would be updated according to the latest laws and regulations of related
regions. For detailed information, see the paper manual, CD-ROM, QR code or our official
website. If there is inconsistency between paper manual and the electronic version, the
electronic version shall prevail.
All the designs and software are subject to change without prior written notice. The product
updates might cause some differences between the actual product and the manual. Please
contact the customer service for the latest program and supplementary documentation.
There still might be deviation in technical data, functions and operations description, or
errors in print. If there is any doubt or dispute, please refer to our final explanation.
Upgrade the reader software or try other mainstream reader software if the manual (in PDF
format) cannot be opened.
All trademarks, registered trademarks and the company names in the manual are the
properties of their respective owners.
Please visit our website, contact the supplier or customer service if there is any problem
occurred when using the device.
Поставщик систем безопасности TELECAMERA.RU

II
If there is any uncertainty or controversy, please refer to our final explanation.
Поставщик систем безопасности TELECAMERA.RU

III
Important Safeguards and Warnings
The following description is the correct application method of the device. Please read the
manual carefully before use to prevent danger and property loss. Strictly conform to the manual
during application and keep it properly after reading.
Operating Requirement
Do not place and install the device in an area exposed to direct sunlight or near heat
generating devices.
Do not install the device in a humid, dusty or fuliginous area.
Keep its horizontal installation, or install it at stable places, and prevent it from falling.
Do not drip or splash liquids onto the device; do not put on the device anything filled with
liquids to prevent liquids from flowing into the device.
Install the device at well-ventilated places; do not block its ventilation opening.
Use the device only within rated input and output range.
Do not dismantle the device arbitrarily.
Transport, use and store the device within allowed humidity and temperature range.
Power Requirement
The product shall use electric wires (power wires) required by the region where the device
will be used.
Use power supply that meets SELV (safety extra low voltage) requirements, and supply
power with rated voltage that conforms to Limited Power Source in IEC60950-1. For
specific power supply requirements, refer to device labels.
Appliance coupler is a disconnecting device. During normal use, keep an angle that
facilitates operation.
Поставщик систем безопасности TELECAMERA.RU

IV
Table of Contents
Foreword.................................................................................................................................................... I
Important Safeguards and Warnings.................................................................................................... III
1 Network Diagram................................................................................................................................... 1
2 Appearance............................................................................................................................................ 2
VTO2101E-P.................................................................................................................................22.1 2.1.1 Front Panel ......................................................................................................................... 2
2.1.2 Rear Panel.......................................................................................................................... 3
VTO3211D-P................................................................................................................................. 32.2 2.2.1 Front Panel......................................................................................................................... 3
2.2.2 Rear Panel.......................................................................................................................... 4
VTO2211G/VTO1201G................................................................................................................. 6
2.3 2.3.1 Front Panel ......................................................................................................................... 6
2.3.2 Rear Panel.......................................................................................................................... 7
3 Installation............................................................................................................................................ 10
Notice.......................................................................................................................................... 103.1 Guidance..................................................................................................................................... 103.2
4 Configuration....................................................................................................................................... 11
Configuration Process..................................................................................................................114.1 VDPConfig ...................................................................................................................................114.2 Configuring Door Stations (VTO).................................................................................................114.3 4.3.1 Initialization........................................................................................................................11
4.3.2 Configuring Door Station (VTO) Number ......................................................................... 12
4.3.3 Configuring Network Parameters..................................................................................... 13
4.3.4 Configuring SIP Server..................................................................................................... 14
4.3.5 Configuring Call No. and Group Call................................................................................ 15
4.3.6 Adding Door Station (VTO)............................................................................................... 15
4.3.7 Adding Room Number...................................................................................................... 17
Verifying Configuration................................................................................................................ 194.4 4.4.1 Calling VTH from VTO...................................................................................................... 19
4.4.2 Watching Monitoring Videos on the VTH.......................................................................... 19
5 App Installation and Adding Device.................................................................................................. 21
5.1.2 Add through Wired Network.............................................................................................. 23
5.1.3Add through Soft Access Point (AP)................................................................................. 24
Cybersecurity Recommendations................................................................................... 32Appendix 1
Поставщик систем безопасности TELECAMERA.RU

1
1 Network Diagram
Поставщик систем безопасности TELECAMERA.RU

2
2 Appearance
VTO2101E-P2.1
2.1.1 Front Panel
VTO2101E-PFigure 2-1
Table 2-1 Front panel description
No.
Name
Description
1
MIC
Inputs audio.
2
Camera
Monitors doorway area.
3
IR illunimation
light
Provides extra IR light for the camera when it
is dark.
4
Light sensor
Detects ambient lighting condition.
5
Call button
Press the button to call VTH or the
management center.
6
Speaker
Outputs audio.
Поставщик систем безопасности TELECAMERA.RU

3
2.1.2 Rear Panel
VTO2101E-PFigure 2-2
Table 2-2 Rear panel description
No.
Name
Description
1
Network port
Connected to the network with network cables.
2
RS-485 ports
See Figure 2-3 and Table 2-3.
3
Cable tray
You can thread cables through the cable tray.
Cable connectionFigure 2-3
Table 2-3 Port description
DOOR
POWER/485
No.
Name
No.
Name
1
NO
1
+12V
2
NC
2
GND
3
COM
3
RS-485A
4
ALARM IN
4
RS-485B
VTO3211D-P2.2
2.2.1 Front Panel
Number of buttons on the front panel varies on different models. VTO3211D-P2 has two
buttons; VTO3211D-P4 has four buttons. VTO3211D-P4 will be taken as an example.
Поставщик систем безопасности TELECAMERA.RU

4
VTO3211D-PFigure 2-4
Table 2-4 Front panel description
No.
Name
Description
1
IR illumination
light
Provides extra IR light for the camera when
it is dark.
2
Camera
Monitors doorway area.
3
Speaker
Outputs audio.
4
Call button
Press the button to call VTH or the
management center.
5
MIC
Inputs audio.
2.2.2 Rear Panel
VTO3211D-PFigure 2-5
Поставщик систем безопасности TELECAMERA.RU

5
Table 2-5 Rear panel description
No.
Name
Description
1
Cable ports
See Figure 2-6 and Table 2-6.
2
Cable tray
You can thread the cable through the cable tray.
Cable connectionFigure 2-6
Table 2-6 Cable port description
No.
Name
No.
Name
1
ALM_COM
7
DOOR_FEED
2
ALM_NO
8
DOOR_NC
3
ALM_IN
9
DOOR_COM
4
RS485B
10
DOOR_NO
5
RS485A
11
GND
6
DOOR_OPEN
12
DC 12V
Поставщик систем безопасности TELECAMERA.RU

6
VTO2211G/VTO1201G2.3
2.3.1 Front Panel
Front panel of VTO2211G/VTO1201GFigure 2-7
Table 2-7 Front panel description
Name
Description
1
Camera
2
Press the button to call indoor monitor (VTH) or the management center.
3
Indicator light.
Off: The device in standby mode;

Solid green: door station (VTO) making a call;

Solid blue: door station (VTO) during a call;

Yellowish green: When you unlock the door through VTH while door

station (VTO) is making a call.
Bluish red: When you unlock the door through VTH while you are

having a call with the door station (VTO);
Green breathing light: The network is disconnected.

4
Card reader (only for VTO2211G).
Поставщик систем безопасности TELECAMERA.RU

7
2.3.2 Rear Panel
Rear panel of VTO2211G/VTO1201GFigure 2-8
Table 2-8 Rear panel description
No.
Description
No.
Description
1
Network port
3
Ports
2
SD card cover
4
Tamper button
VTO2211G cable connectionFigure 2-9
Поставщик систем безопасности TELECAMERA.RU

8
Table 2-9 Port description
No.
Name
No.
Name
1
Alarm input device
14
DOOR1_NC
2
Alarm output device
15
Not available
3
DC_IN-
16
DOOR1_COM
4
DC_IN+
17
Not available
5
ALARM_IN
18
DOOR1_NO
6
+12V_OUT
19
Not available
7
GND
20
GND
8
GND
21
Not available
9
ALARM_NO
22
DOOR1_FB
10
RS485B
23
Not available
11
ALARM_COM
24
GND
12
RS485A
25
Not available
13
Not available
26
DOOR1_PUSH
VTO1201G cable connectionFigure 2-10
Table 2-10 Port description
No.
Name
No.
Name
1
DC_IN-
13
Not available
2
DC_IN+
14
Not available
3
Not available
15
Not available
4
Not available
16
Not available
5
Not available
17
Not available
6
Not available
18
Not available
7
Not available
19
Not available
8
Not available
20
Not available
9
Not available
21
Not available
10
Not available
22
Not available
11
Not available
23
Not available
12
Not available
24
Not available
Поставщик систем безопасности TELECAMERA.RU

9
Connecting lock cablesFigure 2-11
Table 2-11 Port description
No.
Name
No.
Name
1
DC_IN-
14
DOOR1_COM
2
DC_IN+
15
Not available
3
ALARM_IN
16
DOOR1_NO
4
+12V_OUT
17
Not available
5
GND
18
GND
6
GND
19
Not available
7
ALARM_NO
20
DOOR1_FB
8
RS485B
21
Not available
9
ALARM_COM
22
GND
10
RS485A
23
Not available
11
Not available
24
DOOR1_PUSH
12
DOOR1_NC
25
Magnetic lock
13
Not available
26
Electric lock
Поставщик систем безопасности TELECAMERA.RU

10
3 Installation
Notice3.1
Do not install the door station (VTO) at places with condensation, high temperature, grease
or dust, chemical corrosion, direct sunlight, or zero shelter.
The installation and adjustment must be finished by professionals, and do not disassemble
the VTO.
Guidance3.2
See Figure 3-1 the installation position. The door station (VTO) horizontal angle of view varies
with different models, face the center of the door station (VTO) as much as possible.
Installation position referenceFigure 3-1
Поставщик систем безопасности TELECAMERA.RU

11
4 Configuration
This chapter introduces how to initialize, connect, and make primary configurations to door
stations (VTO) and indoor monitors (VTH) to realize basic functions, including device
management, calling, and monitoring. For details, see the user manual.
Configuration Process4.1
Before configuration, check each device and make sure there is no short circuit or open circuit.
Plan IP address for each device, and also plan the apartment number and roomStep 1 number you need.
Configure door stations (VTO). See "4.3 Configuring Door Stations (VTO)."Step 2 1) Initialize door stations (VTO). See "4.3.1 Initialization."
2) Configure door station (VTO) numbers. See "4.3.2 Configuring Door Station (VTO)
Numbers."
3) Configure door station (VTO) network parameters. See "4.3.3 Configuring Network
Parameters."
4) Configure SIP Server. See "4.3.4 Configuring SIP Server."
5) Configure target room number and group call. See "4.3.5 Configuring Call No. and
Group Call."
6) Add door stations (VTO) to the SIP server. See "4.3.6Adding Door Station (VTO)."
7) Add room number to the SIP server. See "4.3.7 Adding Room Numbers."
Configure indoor monitors (VTH). See the VTH user's manual.Step 3 Verify Configuration. See "4.4 Verifying Configuration."Step 4
VDPConfig4.2
You can download the "VDPConfig" and perform device initialization, IP address modification
and system upgrading for multiple devices at the same time. For the details, see the
corresponding user's manual.
Configuring Door Stations (VTO)4.3
Connect the door station (VTO) to your PC with network cable, and for first time login, you need
to create a new password for the web interface.
4.3.1 Initialization
The default IP address of door station (VTO) is 192.168.1.110, and make sure the PC is in the
same network segment as the door station (VTO).
Connect the door station (VTO) to power source, and then boot it up.Step 1
Поставщик систем безопасности TELECAMERA.RU

12
Open the internet browser on the PC, then enter the default IP address of the doorStep 2 station (VTO) in the address bar, and then press Enter.
Device initialization
Figure 4-1
Enter and confirm the password, and then click Next.Step 3 The email setting interface is displayed.
Select the Email check box, and then enter your Email address. This Email addressStep 4 can be used to reset the password, and it is recommended to finish this setting.
Click Next. The initialization succeeded.Step 5 Click OK.Step 6 Login interfaceFigure 4-2
4.3.2 Configuring Door Station (VTO) Number
The door station (VTO) number can be used to differentiate each door station (VTO), and it is
normally configured according to apartment or building number.
You can change the number of a door station (VTO) when it is not working as SIP server.
The door station (VTO) number can contain 5 numbers at most, and it cannot be the same
as any room number.
Поставщик систем безопасности TELECAMERA.RU

13
Log in to the web interface of the door station (VTO), and then the main interface isStep 1 displayed. Main interface
Figure 4-3
Select Local Setting > Basic.Step 2 Device propertiesFigure 4-4
In the No. input box, enter the door station (VTO) number you planned for the doorStep 3 station (VTO) you are operating, and then click Confirm to save.
4.3.3 Configuring Network Parameters
Select Network Setting > Basic.Step 1 TCP/IP informationFigure 4-5
Enter the network parameters you planed, and then click Save.Step 2
Поставщик систем безопасности TELECAMERA.RU

14
The door station (VTO) will restart, and you need to modify the IP address of your PC to
the same network segment as the door station (VTO) to log in again.
4.3.4 Configuring SIP Server
The SIP server is required in the network to transmit intercom protocol, and then all the door
station (VTO) and indoor monitor (VTH) connected to the same SIP server can make video
calls among each other. You can use door stations (VTO) or other servers as SIP server.
Select Network Setting > SIP Server.Step 1 SIP serverFigure 4-6
Select the server type you need.Step 2
If the door station (VTO) you are visiting works as SIP server
Select the Enable check box at SIP Server, and then click Save.
The door station (VTO) will restart, and after restarting, you can then add door
stations (VTO) and VTH devices to the door station (VTO) you are operating. See
"4.3.6 Adding Door Station (VTO) and 4.3.7 Adding Room Number."
If the door station (VTO) you are visiting does not work as SIP server, do not select the
Enable check box at SIP Server, otherwise the connection will fail.
If other door station (VTO) works as SIP server
Select VTO in the Server Type list, and then configure the parameters. See Table
4-1.
Table 4-1 SIP server configuration
Parameter
Description
IPAddr.
The IP address of the door station (VTO) which
works as SIP server.
Port
5060
Username
Keep the default value.
Password
SIP Domain
VDP
Поставщик систем безопасности TELECAMERA.RU

15
Parameter
Description
SIP Server Username
The user name and password for the web
interface of the SIP server.
SIP Server Password
If other servers work as SIP server
Select Express/DSS in the Server Type list, and then see the corresponding
manual for the detailed configuration.
4.3.5 Configuring Call No. and Group Call
You need to configure call No. on each door station (VTO), and then all the door stations (VTO)
can call the defined room when you press the call button. On the SIP server, you can enable
group call function, and when calling a master indoor monitor (VTH), the extension indoor
monitors (VTH) will receive the call as well.
After enabling or disabling group call function the door station will restart.
Select Local Setting > Basic.Step 1 Device propertiesFigure 4-7
In the No. input box, enter the room number you need to call, and then click Confirm toStep 2 save. Repeat this operation on every villa door station (VTO) web interface.
Log in to the web interface of the SIP server, and then select Local Setting > Basic.Step 3 Select the Group Call check box, and then click Confirm.Step 4 The door station (VTO) will restart, and when calling a master indoor monitor (VTH), the
extension indoor monitor (VTH) will receive the call as well.
4.3.6 Adding Door Station (VTO)
You can add door stations (VTO) to the SIP server, and all the door stations (VTO) connected to
the same SIP server can make video calls among each other. This section applies to the
condition in which a door station (VTO) works as SIP server, and if you are using other servers
as SIP server, see the corresponding manual for the detailed configuration.
Log in to the web interface of the SIP server, and then select Household Setting >Step 1 VTO No. Management.
Поставщик систем безопасности TELECAMERA.RU