Dancover TITAN Classic User manual

26-02-2019
for
Greenhouse
TITAN Classic
Manual

2 m
3,3 m
2,1 m

3
2
TECHNICAL CERTIFICATE/GREENHOUSE “TITAN Classic”
Follow the greenhouse assembly instructions and use it in strict accordance
with the manual and operating rules stated in the technical certificate. Please
keep the technical certificate for further reference.
!
DISCRIPTION
The greenhouse “TITAN Classic” is designed to create the climate, which is productive to
grow horticultural crops on the garden plots.
The length of the greenhouse is 3.3 m, the surface of the protected soil is 6.4 m2. The height
of the set up frame is 2.1 m.
The frame of the greenhouse is made of square galvanized pipe and it is assembled with the
studs, screws, nuts. The kit includes everything you need to fasten the covering.
The base of the greenhouse is not obligatory to install but recommended. The greenhouse is
fixed on the ground by digging special frame endings. The kit includes everything you need to
fasten the covering.
The greenhouse covering is completed on buyer’s request. To cover the greenhouse you need
2.5 polycarbonate sheets 4*2100*6000 mm.
The greenhouse has two doors and two vents.
Assembly instructions and operating rules
The green house should be assembled and installed on the ground according the instruction.
The buyer should control the assembly quality if it is made by third person.
Self-tapping screws of mount structure should be tightened to contact the flat head of the
screw with the covering surface and hold it to the frame, but do not allow the extra rundown of
the screws.
Avoid installing the greenhouse closely to the buildings and trees. The melting snow or ice is
a potential hazard. The recommended distance is minimum 2.2 m.
The greenhouse is designed to endure the wind of less than 20 m/s.
There is no need to skin the greenhouse during the winter time for the greater parts of the
regions of Russia. If the greenhouse in not looked after during winter, the customer should
determine the possible snow load or to skin the covering.
The limit snow load for the frame takes place when the weight of the snow blanket is 240
kg/1m2 of horizontal ground surface. This limit snow load requires characteristic snow load
of the IV snow region (according the classification of construction rules and regulations (SNiP)
2.01.07-85 “Loads and actions”.
If the greenhouse is installed according the instruction, the manufacture guarantees the
durability of the frame when the snow covers it in Moscow, Sverdlovsk, Novosibirsk and other
regions which are not exceeding IV snow region number. Buying a greenhouse, ascertain data
of snow region number where the green house is planned to be installed.

5
4
TECHNICAL CERTIFICATE/GREENHOUSE “TITAN Classic”
The manufacturer reserves the right for greenhouse engineering design changes.
Warranty
1. The manufacturer shall be responsible for completeness of the package.
2. The manufacturer shall be responsible for assemblability of the greenhouse in accordance with
the Assembly Instruction.
3. The manufacturer shall be responsible for structural integrity within the frames of the Operating
Rules.
4. The term for a claim is 24 months from the date of purchase.
Warranty liability
Cleaning and washing of the polycarbonate sheets
Warranty liabilities do not apply to cases of:
1. The greenhouse installation with violation of requirements of the manual
2. The violation of the operating rules.
3. Inappropriate use of the greenhouse.
4. The evidence that indicates corrosion on the cut of the details which do not influence the
operational characteristics of the construction.
5. The deformation of the greenhouse due to soil movement.
6. Floods, hurricanes and other natural disasters.
7. The deformation of the greenhouse under the show due to operational characteristics
violation.
1. Swill the sheets with warm water.
2. Wash the sheet with a solution of mild soap or household detergent and warm
water, using a soft cloth or sponge to remove dirt.
3. Swill with cold water and dry with soft rag.
Never use abrasives or highly alkaline cleaning compositions for cleaning polycarbonate
sheets. Dry rubbing of the surface will damage the protective layer of the cladding and shorten
its application time. Never rub the surface of polycarbonate sheets with brushes, metallic cloth
or other abrasive materials.
When disinfecting the greenhouse from pathogens causing fungal and bacterial diseases,
do not use “sulfur blocks” to avoid frame corrosion (blackening).
М2
bearer (20х20)
L=0,64m
х 30
М2-1
bearer (20х20)
L=0,64m
х 5
1package header (20х20)
L=0,3m
х 16
М5 roof
(20х20)
L=1,16 m
х 4
М5-1 roof
(20х20)
L=1,17 m
х 4
М5К roof
(20х20)
L=1,16 m
х 2
М5К-1 roof
(20х20)
L=1,17 m
х 2
М4 side stud
(20х20) L=1,55m
х 8
М4К
side stud end most
(20х20)
L=1,55m
х 4
М21 hard bar of the arc
(20х20)
х 12
М8
isohyps end face (20х20)
L=0,58 m
х 4
М8-1 isohyps end face
(20х20)
L=0,58 m
х 4
М9 door side stud
(20х20)
L=1,87 m
х 2
М9-1
door side
stud (20х20)
L=1,87m
х 2
М10
door side isohyps (20х20)
L=0,81m
х 2
D10-1y
х 2
1ST PACKAGE BASE
2ND PACKAGE BASE
3 RD PACKAGE BASE
4 TH PACKAGE BASE

7
6
22
plate
L=1,53m
х 12
23
plate
L=1,16m
х 12
24
end face plate
L=1,53m
х 4
25
end face plate
L=1,16m
х 4
26
roof apex
х 5
3Runner
х 16
27
Door hook
х 2
28
Door Butt
х 8
29
Door bolt handle
х 12
30
Plate of the
door bolt
х 6
31
Inside part of
the door bolt
х 12
32
Valve chamber
of the door bolt
х 6
33
Rod of the
door bolt
х 6
34
Scotch tape
х 1
А11у
vertical vent member
(20х20)
L=0,9 m
х 4
А 11-1у
х 2
А 11-2у
х 2
А12-1у
isohyps vent member (20х20)
L=0,75 m
х 2
А 12-2у
х 2
А 12-3у
х 2
А 12-4у
х 2
5 TH PACKAGE BASE
6 TH PACKAGE BASE
35 Screw М4х30
х 40
36 Screw М5х30
х 12
37 Screw М6х30
х 16
38 Screw М6х30
х 36
39 Screw М6х45
х 18
40 Stud
М4х45
х 6
41 Stud
М6х55
х 32
42 Self-tapping screw М4,2х19
х 280
43 Door weather strip
1,9m х 2
44 Nut M4 х 40
45 Nut M5
х 12
46
Nut M6 х 36
6 TH PACKAGE BASE4 TH PACKAGE BASE

9
8
М4К
М5К
1
М9
М5К
М4К
М8
М8-1
М4К
М8-1
М4К
М8
М4К
М8
х1
M6x30
х1
М6
х1
M6x45
х1
M6x45
х1
M6x45
х2
М9-1
М5К-1
М10
D10-1У
М4К
М8-1
М8
М9-1
D10-1У
М8
М5К-1
М9-1
М10
М5К-1
М5К
х1
M6x45
х2
M6x30
х2
М6
х1
М6х55
1
1
3
х2
M4,2x19

11
10
2
х1
М6х55
х1
М6х55
х1
М6х55
х1
х1
M6x30
х1
х1
M6x30
х1
х1
M6x30
М4-1
М5
М5-1
М21
М21
М21
М4
х1
М6х55
М5-1
М21
М4 1
М4
М21
М5
М5-1
М6
М6
М6
3
4
х1
M6x45
M2 M2 M2
M4
х1
М6х55
M2
M2-1
M2
M2
M2
M2
M2

13
12
660
20
20
5
L1
L2
L1=L2
!
6
D11-2У
х2
D12-1У
D12-4У
D11-2У
D11У
D11У D11У
D12-1У
M6x30
х2 х4
M4x30
х4
х2
М4
D12-4У
х4
М5
х4
M5x30
А
D12-4У
The measurements for base installation.
1980
582
816
3300

15
14
7
8
The UV-resistant side of polycarbonate sheets must
face outside (sunward). The UV-resistant side is usually
indicated with notations on the shipping plastic film. The
film is transparent on the back side of the polycarbonate
sheet. After marking the polycarbonate sheets, but prior
to cutting it, mark the UV-resistant side on every piece of
polycarbonate sheet: when the shipping film is removed
both sides look similar. The shipping film is removed
from both sides shortly before fastening the covering in
the frame.
Tape scotch on the cut sides of the polycarbonate
sheets.
D11У
D12-2У
D11-1У
х4
M4x30
х4
х2
М4
х2
М5
х2
M5x30
х2
D12-2У
D12-3У
D11-1У
D11У
В
D11У
D12-3У
A
A
В
D
C
х2
M6x30
E
E
F
F
F
F
H
H
D
C
670
2100
660
600
600
796
255
1200
793
793
1185
1185
15331881
930
6000
910

17
16
H H H
G
G
G G
KK K
K K K
В
H
2100
6000
2100
660
670
660
6000
1535
1535 1185