Danfoss BT27IK User manual

IK4 start up
Use the information below to properly turn the transmitter ON (OPERATION mode).
1. Place a charged battery in the transmitter. The charge must be done following the instructions of the
Battery Chargers' Manual.
2. Turn the contact key.
1
FUDQH[[

0
1
0
1
>ƉƵůƐĞ ĚŝƐƉůĂLJŽƉ௭ŽŶ
>ƉƵůƐĞ
3. Push and pull out the STOP button.
LED will flash orange-green pulse. If the transmitter has LCD, it displays the identification of the
machine and battery level (only if it has been pre-programmed).
FUDQH[[
>ƉƵůƐĞ ŝƐƉůĂLJŽƉƚŝŽŶ
4. Press the start button. The green LED will now light to indicate the transmitter is transmitting. Once
the Tx is connected, press any maneuver button and its corresponding relay will be activated. Check
to make sure all other maneuvers work in a coherent way with the expected movements.
1
FUDQH[[

0
1
0
1
>ƉƵůƐĞ ĚŝƐƉůĂLJŽƉ௭ŽŶ
>ƉƵůƐĞ
User Manual
IK4 Transmitter
Technical description
Danfoss | February 2019 BC290863558440en-000101 | 7
IK4 start up
Use the information below to properly turn the transmitter ON (OPERATION mode).
1. Place a charged battery in the transmitter. The charge must be done following the instructions of the
Battery Chargers' Manual.
2. Turn the contact key.
1
FUDQH[[

0
1
0
1
>ƉƵůƐĞ ĚŝƐƉůĂLJŽƉ௭ŽŶ
>ƉƵůƐĞ
3. Push and pull out the STOP button.
LED will flash orange-green pulse. If the transmitter has LCD, it displays the identification of the
machine and battery level (only if it has been pre-programmed).
FUDQH[[
>ƉƵůƐĞ ŝƐƉůĂLJŽƉƚŝŽŶ
4. Press the start button. The green LED will now light to indicate the transmitter is transmitting. Once
the Tx is connected, press any maneuver button and its corresponding relay will be activated. Check
to make sure all other maneuvers work in a coherent way with the expected movements.
1
FUDQH[[

0
1
0
1
>ƉƵůƐĞ ĚŝƐƉůĂLJŽƉ௭ŽŶ
>ƉƵůƐĞ
User Manual
IK4 Transmitter
Technical description
Danfoss | February 2019 BC290863558440en-000101 | 7
DANFOSS BT27IK

CB70 and BT27IK specifications
CB70 battery charger
Specification Value
Standard AC power supply 230 Vca ± 10%, 50
Optional AC power supply 115 Vca, 60 Hz
DC power supply From 10.5 V to 35 V
BT27IK battery
Specification Value
Voltage 4.8 V
Capacity 2700 mAh NiMH
Charging temperature From 0° C to 45° C
Discharge temperature From -20° C to 50° C
Autonomy From 14 to 20 h (use at 50%)
Charging mode Fast (<2 h) and intelligent
Weight 156.3 g
Setting up the CB70 battery charger
Use the information below to properly set up the CB70 batter charger.
The battery charger has two charging compartments that can simultaneously charge two batteries.
1. Connect the charger to a power source using the cable supplied.
The red LED will switch.
User Manual
IK4 Transmitter
Charger and battery
Danfoss | February 2019 BC290863558440en-000101 | 9