Datalogic Memor X3 User manual

Memor™ X3 Single Ethernet Dock
Read this manual carefully before performing any type
of connection through the Memor X3 Single Ethernet
Dock.
The user is responsible for any damages caused by
incorrect use of the equipment or by inobservance of the
indication supplied in this manual.
NOTE
Do not attempt to disassemble the Memor X3
Single
Ethernet Dock
, as it does not contain parts that can be
repaired by the user. Any tampering will invalidate the
warranty.
NOTE
The Memor X3 Single Ethernet Dock paired with one Memor X3 mobile
computer builds a reading system for the collection, decoding and
transmission of barcoded data.
The communication between the mobile computer and host PC through
the Memor X3 Single Ethernet Dock may occur also by using the standard
ActiveSync® connection.
Figure 1 – Memor X3 Single Ethernet Dock
A) LED Indicators
B) Spare Battery Slot
C) Mini USB Connector
D) RS232 Connector
E) Power Jack
F) Ethernet Port with LED indicators
G) Switch Ethernet/USB
The Memor X3 Single Ethernet Dock is a serial communication adapter
between the host computer and the Memor X3 mobile computer. Power
supply is required to be connected to the Dock only for ethernet
communication.
Since the Memor X3 Single Ethernet Dock also functions as a battery
charger, a power supply is required for battery recharging operations, both
for the mobile computer and spare battery pack recharging. The spare
battery pack recharging slot can supply a 1100 mAh, a 1430 mAh, a 2000
mAh and a 2300 mAh Battery pac.
822001522(Rev. A) Jan. 2018
MOBILE COMPUTER INSERTION/ REMOVAL
By inserting the Memor X3 into the Dock, data can be transmitted to the
host and its battery begins charging if the power supply is connected. In
addition, a spare battery can be charged by inserting it into the slot at the
back of the Memor X3 Single Ethernet Dock as shown in the following
figure.
Figure 2 – Memor X3 Single Ethernet Dock Charging and
Communication
LED INDICATORS
The LEDs positioned on the front part of the Memor X3 Ethernet Dock
(see figure below) indicate the Dock and spare battery charger status:
Figure 3 - LED Indicators
Front LED indicators
LED STATUS
Charger
Red Constant
Spare battery charging*
Green Constant
Spare battery charge completed
Power
Green
It is constant when the Dock is powered
*During charging, the LED may turn off to indicate a temporary
suspension of charging.
Ethernet Connector LED Indicators
Ethernet
Green LED
(left)
Solid Green Link established
Flashing Green
Link activity
Off
No link established
Ethernet
Yellow LED
(right)
Off
10 Mb connection
Solid Yellow
100 Mb connection (this model is not
available)
CONNECTIONS
Connections should always be made with power OFF!
CAUTION
USB Connection
The Memor X3 Single Ethernet Dock can be connected to the host by
means of any standard Mini USB cable.
Once the host has been turned on, insert the Memor X3 mobile
computer into the Dock.
Figure 4 - USB Connection
A) Host Computer
C) Memor X3 Single Ethernet Dock
B) Std Mini USB (i.e.
94A051016 CAB-421)
D) Power Supply*(only necessary
for battery charging)
Be sure that the switch is in the “USB” position.
During switch operation from USB position to Ethernet
position and vice versa the mobile computer must not be
inserted in the Dock.
NOTE
*Recommended power supply: 94ACC1324 PG5-30P35 AC/DC POWER
SUPPLY EU/USA PLUG.
B
C
D
F
G
E
A
Spare Battery
Charger LED
Power LED
A
B
C
D
Spare battery
Charge Slot with
Spare Battery
Inserted
Data Transmission and
Mobile Computer Battery
Charging

RS232 Connection
The Memor X3 Single Ethernet Dock can be connected to the host by
means of any standard null modem cable. The 9-pin female D-Sub
connector must be connected to the RS232 port of the Dock.
Once the host has been turned on, insert the Memor X3 mobile
computer into the Dock.
Figure 5 - RS232 Connection
A) Host Computer
C) Memor X3 Single Ethernet Dock
B) Null Modem cable D) Power Supply* (only necessary
for battery charging)
Be sure that the switch is in the “USB” position.
During switch operation from USB position to Ethernet
position and vice versa the mobile computer must not be
inserted in the Dock.
NOTE
Ethernet Connection
Connect the Ethernet Dock (Ethernet port ) to an Ethernet hub or a port on the
host device. Connect the Power jack to a power supply*.
Figure 6 - Ethernet Connection
A) Memor X3 Single
Ethernet Dock
C) UTP CAT 5E cable
(recommended use)
B) Ethernet hub
D) Power supply
*
*Recommended power supply: 94ACC1324 PG5-30P35 AC/DC POWER
SUPPLY EU/USA PLUG
Do not use the cradle in a PoE network, i.e. in a network
with PSE able to supply
power: there is the risk to
compromise, in irreversible way, the functionality of the
cradle.
WARNING
Be sure that the switch is in the “Ethernet” position
During switch operation from USB position to Ethernet
position and vice versa the mobile computer must not be
inserted in the Dock.
NOTE
You may need to set the Dock configuration or the
terminal behaviour using respectively the "Dock
Manager" Windows XP application and the "CPDockCE"
Windows CE application. You can download the "Dock
Manager" installation file and the full "Memor X3 Single
Dock User Guide" from the Datalogic Mobile website:
www. datalogic.com.
NOTE
TECHNICAL FEATURES
Memor X3 Single Ethernet Dock
Electrical Features
Power Supply*
5 VDC ± 5%
Consumption
Max. 2.5 A
Indicators
Power on LED (green)
Spare battery charge LED (bi-colored)
Ethernet LEDs (green and yellow)
Charge Time
- 1100 mAh Battery: max. 2 hours spare battery
only; max. 3 hours with terminal and spare
battery
- 2000 mAh Battery: max. 4 hours spare battery
only; max. 6 hours with terminal and spare
battery
- 1430 mAh Battery: max. 3 hours spare battery
only; max. 4 hours with terminal and spare
battery
- 2300 mAh Battery: max. 5,5 hours spare
battery only; max. 7,5 hours with terminal and
spare battery
Communication Features
Interface
RS232, USB 1.1 version, Ethernet
Baud Rate
RS232 = up to 115200 b/sec; USB = up to 12
Mb/sec; Ethernet = up to 10 Mbps
Environmental Features
Working Temperature**
0° to +50 °C (+32° to +122 °F)
Storage Temperature
-20° to +65 °C (-4° to +149 °F)
Humidity
80% non condensing
Degree of Protection
IP50
Mechanical Features
Dimensions
105 X 75 X 102 mm (4.13 X 2.95 X 4.02 in)
Weight
340 g (12 oz)
*Recommended power supply: 94ACC1324 PG5-30P35 AC/DC
POWER SUPPLY EU/USA PLUG.
** Battery must be charged at a temperature ranging from 0° to +36
°C (+32° to +97 °F).
COMPLIANCE
FCC Compliance
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
This device has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates,
uses and can radiated radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
−Reorient or relocate the receiving antenna.
−Increase the separation between the equipment and receiver.
−Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
−Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible
for compliance could void the user‘s authority to operate the equipment.
Industry Canada (ICES-003) Compliance
This Class B digital apparatus complies with Canadian ICES-
003.
Cet appareil numérique de la classe B est conforme à la norme
NMB-003 du Canada.
©2013-2018 Datalogic S.p.A. and/or its affiliates. All rights reserved.
Datalogic and the Datalogic logo are registered trademarks of Datalogic
S.p.A. in many countries, including the U.S. and the E.U. Memor is a
trademark of Datalogic S.p.A. and/or its affiliates. All other brand and
product names may be trademarks of their respective owner.
www.datalogic.com
A
B
C
D
D
A
C
B