DAXYS BANDICOOT User manual

USER MANUAL v1.0
BANDICOOT
Electric Kickscooter

BANDICOOT USER MANUAL
Please read this manual very carefully before using the product. The
manual contains important instructions for the safe use and longevity
of your scooter.

1
DAXYS BANDICOOT - USER MANUAL
CONTENTS
Riding Introduction .......................................................................................................................................... 2
Safety Information ........................................................................................................................................... 2
Statement of Responsibility............................................................................................................................. 3
Product Disclaimer.......................................................................................................................................... 3
Before You Ride............................................................................................................................................... 4
Battery Disposal.............................................................................................................................................. 5
Meet Your Scooter ........................................................................................................................................... 6
Display Guide.................................................................................................................................................. 7
Handlebar Guide ............................................................................................................................................. 8
Product Specifications .................................................................................................................................... 9
Assembly Instructions ................................................................................................................................... 10
Charging The Battery .................................................................................................................................... 12
Battery and Charger Information.................................................................................................................... 13
Operating Your Scooter ..................................................................................................................................14
Guide to Speed Modes .................................................................................................................................. 15
Your eScooter Keys ....................................................................................................................................... 15
Maintenance
Tyres.......................................................................................................................................................... 16
Bearing lubrication .................................................................................................................................... 16
Cleaning Your eScooter .............................................................................................................................. 16
Troubleshooting .............................................................................................................................................17
F.A.Q’s .......................................................................................................................................................... 18
Warranty........................................................................................................................................................ 19
Technical Support Contact information.......................................................................................................... 20

2
RIDING INTRODUCTION
Do not use the product before carefully reading the instructions and understanding the performance of the product;
Before cycling, check whether the brakes work. When braking, please brake rear first and then front. Pay attention to
the brake tightness. If the brake is too loose, use an Allen wrench to tighten it. Pay attention to increase the braking
distance when riding in rain and snow. Applicable age: 16 ~ 65 years old. Please wear safety helmets and obey the
traffic rules when cycling. It is not allowed to drive in motor lanes and roads with more pedestrians. Please check the
tyres before using. The recommended tyre pressure is 30(max) PSI. When using the motor, pay attention not to hit it
vigorously and keep the rotating shaft lubricated. The maximum load is 120kg.
SAFETY INFORMATION:
ALWAYS WEAR A HELMET AND SAFETY
EQUIPMENT
Helmets significantly reduce the number and severity of
head injuries. Always wear a helmet that complies with
your state laws when riding your eScooter. Make yourself
more visible by wearing bright reflective clothing. Keep
your reflectors clean and properly aligned. Use head
and tail lights in reduced lighting conditions. Wear sturdy
shoes and eye protection. Also check your state laws
concerning other protective gear that may be required
when riding your eScooter.
KNOW YOUR ESCOOTER
Your new eScooter incorporates many features and
functions that you may be unfamiliar with. Read this
manual thoroughly to understand how those features
enhance your riding pleasure and safety.
RIDE WITHIN YOUR LIMITS
This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience
and knowledge, unless they have been given supervision or instruction
concerning use of the appliance by a person responsible for their safety. Not
to be used by children without adult supervision.
Take it slow until you are familiar with the riding conditions, as traction can
be greatly reduced and brakes become less effective. Never ride faster than
conditions warrant or beyond your riding abilities. Remember that fatigue, and
inattention can significantly reduce your ability to make good judgments and
ride safely.
KEEP YOUR eSCOOTER IN SAFE CONDITIONS
For your safety and enjoyment, and to ensure a long life for your eScooter,
inspect and maintain your eScooter regularly.
Follow the inspection and maintenance guidelines throughout this manual.
Check critical safety equipment before each and every ride.

3
DAXYS BANDICOOT - USER MANUAL
STATEMENT OF RESPONSIBILITY:
After riding, please store in a place without direct sunlight and away from rain; Check the motor and brakes
frequently; Regularly check the screws of the eScooter and the places to be tightened, and tighten them regularly.
The front and rear wheels of the vehicle shall be located at the center of the front fork or frame; Frequently
check whether there are scars, cracks or excessive wear in the rotation. The inner tube and air nozzle should be
perpendicular to the wheel hub and should not be tilted. Damage or excessive worn outer tyres needs to be replaced
immediately. Please find a professional technician to replace your tyres.
PRODUCT DISCLAIMER:
The contents of the user manual shall not be copied, modified, reproduced, transmitted or published in any form with-
out the prior written permission of the company.
Please read this manual carefully before using the product and operate in accordance with it, otherwise, the company
will not be responsible for product damage or personal and property losses caused by improper and wrong use.
The company reserves the right to modify and finally interpret the product models, specifications or relevant
information mentioned in this manual; The functions of the specific model mentioned in this manual are only
applicable to the specific model; The product models, specifications or relevant information mentioned in this manual
are subject to any modification or change without notice; Please read this manual carefully before using the product
and operate in accordance with it. Otherwise, the company will not be responsible for product damage or personal
and property losses caused by improper and wrong use.

4
BEFORE YOU RIDE
Perform Regular checks and maintenance as outlined below
COMPONENT OR
CONDITION
INSPECT BEFORE
EVERY RIDE
INSPECT
PERIODICALLY
CLEAND AND/OR
LUBRICATE
ADJUST /
TIGHTEN
REPAIR /
REPLACE
(IF NECESSARY)
Tyre wear/damage
Brake pad
adjustment
Head and tail lights
Controls and
displays
Brake pad wear
Brake cable
tension wear
Wheel true /
Alignment
Hub bearings
Battery and
charger
All bolts, nuts &
mounting hardware

5
DAXYS BANDICOOT - USER MANUAL
MEET YOUR SCOOTER:
14. Charging port
15. Deck
16. Rear drum brake
17. Motor
18. Battery
19. Back light
20. Kickstand
21. Carry handle
22. Back turn light
23. Locking ring
1. Controller
2. LED display
3. Brake lever
4. Front turn light
5. Hook
6. Headlight
7. Stem
8. Folding latch
9. Front mudguard
10. Front shock absorber
11. Front drum brake
12. Wheel fork
13. Wheel
3
4
5
6
7
9
10
11
8
1
2
12
13
15
16
17
18
19
20
21
22
23
14

6
DISPLAY GUIDE:
1. Speed mode indicator
2. Turn ligts
3. Current speed / Error code
4. mph / km/h indicator
5. TRIP (current trip) / ODO (total mileage)
6. Current TRIP/ODO value
7. Unit of measurement (KM / Mile )
8. Battery level
9. Warning indicator (maintenance required)
10. Head light (ON if visible)
11. Cruise control indicator
2
1
3
4
5
6
7
8
9
10
11

7
DAXYS BANDICOOT - USER MANUAL
HANDLEBAR GUIDE:
1 3
4
6
7
10
12
11
13
8. Folding hook
9. Brake cables
10. LED display
11. Regen brake control (electronic brake)
12.Turn lights controls
13. Rear brake lever
1. Handlebar
2. Power and frontlight controller
3. Throttle
4. Front brake lever
5. Right turn light
6. Grip
7. Bell
2
5
9
8

8
PRODUCT SPECIFICATIONS:
Parameter Value
Appearance Dimension Body material Aluminum alloy
Vehicle colour Black pearl
Scooter size Length*width*height:
1276mm*660mm*1260mm
Hub form Pneumatic tubeless (self healing)
Hub size 10”
Package size Length*width*height:
1298mm*220mm*635mm
Performance Parametres Gross / net weight 24.7kgs/29.5kgs
Maximum payload 120kg
Top speed 25Km/h
Endurance Mileage 50-55KM (the lower value is closer to real-life performance)
Maximum climbing angle 25 degree
Service temperature range -10° ~ +40° C
Charger Parametres Input AC 100-240V, 50/60 Hz, 2.5A MAX
Output DC 54.6V 2A 110W
Battery parametres Battery type Lithium ion power battery
Battery capacity 12.6Ah
Battery rated voltage 48V
Under-voltage protection value 30V
Over-current protection value 15±1 A
Charging time 7-8h

9
DAXYS BANDICOOT - USER MANUAL
Parameter Value
Electrical Specifications Motor mode Moped
Motor type 10”/48V/High speed gear
Motor rated power 500W (Standard)
Product Features Instrument display Multi-functional color LED screen
Back lighting Yes
Turn signals Yes
Brakes Front: Drum brakes
Back: Drum and electronic brakes (regen brake)
Tyre style Pneumatic (Self healing tubeless)
Tyre size specification 10”
Front fork suspension Yes, single coil
Middle(rear)shock absorption Yes, dual coil
Speed gear N/A
Headlights Yes
DISCLAIMER:
THE PRODUCT WAS TESTED FULLY CHARGED, WITH AN AVERAGE LOAD OF 75KG-85KG, AT A NORMAL TEMPERATURE ON A NORMAL
PAVED ROAD BETWEEN THE SPEEDS OF 0-25KM/H. THE RESULTS MAY VARY BASED ON DIFFERENCES IN TEMPERATURE, LOAD, WIND
SPEED, ROAD CONDITIONS AND OTHER FACTORS.

10
ASSEMBLY INSTRUCTIONS:
1. Unpack your new Daxys Bandicoot eScooter.
1. UNBOXING
2. Remove the charger box and packing materials.
3. Get the Allen key and accessories ready.
5. Lock the stem with the folding latch.
4. Unfold the stem and pull it to a vertical position.
6. Ensure that the safety lock is flush with the folding latch on the shaft.

11
DAXYS BANDICOOT - USER MANUAL
2. Remove the charger box and packing materials.
4. Unfold the stem and pull it to a vertical position.
2. Check that the cables are connected properly.
3. Carefully fit the cables in the stem cavity.
2. HANDLEBAR INSTALLATION & FOLDING
1. Remove the A, B bolts from the handlebar.
4. Insert the handlebar at the top of the stem.
5. Tighten the A, B bolts.
4. For carrying, release the latch, fold the stem and connect the
stem hook to the locking ring at the end of the deck.
6. Ensure that the safety lock is flush with the folding latch on the shaft.

12
CHARGING THE BATTERY:
Using the charger and Battery guide, charging indicators, level indicators etc.
1. Connect the charger to the battery charging port first.
2. Plug in a power source
3. Check if the LED is RED. If the LED is GREEN, unplug from power source and repeat steps 1. and 2.
4. A full charge will require 4-5 hours, depending on current battery level.
5. Disconnect the charger when the LED turns green, it indicates Full Charge.
1 3
5

13
DAXYS BANDICOOT - USER MANUAL
BATTERY AND CHARGER INFORMATION:
THIS APPLIANCE CONTAINS BATTERIES THAT ARE ONLY REPLACEABLE BY SKILLED PERSONS.
THIS APPLIANCE CONTAINS BATTERIES THAT ARE NON-USER REPLACEABLE.
GOOD PRACTICES
Control the temperature
Avoid charging in extreme temperatures that are outside normal comfort range.
If your battery does get very hot or cold, allow it to come to room temperature before you plug in the charger. Batteries get warm even during normal
use - wait a few minutes post-ride before you start charging.
Use the right charger
For best performance, use the original charger that was supplied with your eScooter. If you must use a different charger (for example: if the original
charger is lost or damaged and replacements are no longer available) check carefully to ensure a 100% match before you charge.
Don’t take it to 0%
Lithium-Ion batterieshave the longest service life when kept in the middle of their capacity. Sometimes, draining is unavoidable, but when possible,
top offbefore 0%. Use the display or the battery indicator on your eScooter’s battery to monitor the charge level.
Don’t overcharge
Charge the scooter battery fully after every ride to prolong batery life.
Keep it dry
Never charge in a damp or wet environment. If your eScooter was ridden in the rain, ensure every component is completely dry before you charge.
Don’t pressure wash your battery, and never submerge it.
Give it some room
Both chargers and batteries can get warm during use. Make sure that anyvents on the charger aren’t blocked and ensure that air can circulate
around all the components. Place chargers on a hard surfaces only.
Don’t use an extension cord
Extension cords adds resistance. While extension cords can be convenient, some chargers may work poorly, or not at all, when plugged into exten-
sion cords. Plug your eScooter charger directly into a wall outlet instead for best results. If required to use an extension cord, use the shortest length
possible, and always check the specs so ensure it can handle your charger’s requirements.
Storage and Warnings
If the battery will not be used for an extended period of time store in a cool, dry place, and keep charged between 70-90%. Make sure to chek it it
every month.
Please ONLY use the original special charger for charging the battery.
If you notice unusual sounds, smells or temperature variations coming from the charger or the battery, unplug charger immediately and contact
customer service.
Improper use of the battery will damage the battery and may cause fires or explosions.
Do not disassemble or alter the battery or battery charger.
Do no place the battery near fire or corrosive substances.
Protect the battery / charger from exposure to liquids and do not use when damp.
Do not expose the battery / charger to extreme conditions.
Do not operate if damaged.
Recharge the battery only with the charger specified by manufacturer.
Do not use the battery / charger for any other purposes except the intended ones.

14
KEY OPERATIONS:
The key operations are short, long and multiple button presses.
Button
Short press functions:
Metre interface Right turn signal light ON/OFF
Long press functions:
Metre interface Right turn signal light ON/OFF
-Button
Short press functions:
Metre interface Left turn signal light ON/OFF
Long press functions:
Metre interface Left turn signal light ON/OFF
Button
Short press functions:
Metre interface Turn headlight ON/OFF
Long press functions:
Metre interface Turn headlight ON/OFF
Button
Short press functions:
Metre interface Change gear (E/D/S)
Double tap to switch between Km/h and Mph
Cruise mode (see bellow)
Long press functions:
Metre interface Power On/Off
Restore factory settings:
Press the electric brake switch (left throtthle) then press the “Power” button on the right dial 8 times in a row and wait for the automatic shutdown.
The brake and accelerator settings will be restored to factory defaults when the scooter is turned on again.
Zero / Non zero start
To activate / deactivate Zero start mode (throttle can be used without the scooter reaching 3km/h) control, press the regen brake switch (left control)
and then press 4 times in quick succession.
Cruise control mode:
To activate / deactivate cruise control, press 4 times in quick succession. The cruise control icon will appear on the display, when
active.
1. The cruise control function is turned on (double beep sound): Press the throttle to max while in riding mode and Cruise mode will start automati-
cally after 8 seconds (Press the brakes, accelerator, or switch gears to exit cruise mode).
2. The cruise control function is turned off (single beep sound): No cruise control mode
Note: Due to ongoing product upgrades, it is possible that some icons and menu items will be different from the above specifications, but will not
affect normal usage.

15
DAXYS BANDICOOT - USER MANUAL
GUIDE TO SPEED MODES:
OFF - no motor assistance
E (ECO)- motor assisted, max. 15km/h
D (DYNAMIC)- motor assisted, max. 20km/h
S (SPORT)- motor assisted, max. 25km/h
Note: Using the brakes will interrupt the motor assistance.
YOUR ESCOOTER KEYS:
This model is not equipped with any locks / unlockable components.

16
TYRES:
Start by doing a visual check, looking for abnormal wear or cracks. If you think your tyre needs replacement based on this check up, you should
follow your instincts. You may bring your tyres to your local bike shop for a competent opinion. While doing your visual inspection, check for proper
tyre pressure by using a tyre gauge suited for testing bicycle tyres. The recommended tyre pressure is 30(max) PSI and is marked on the tyre’s
sidewall. The maximum pressure will carry the maximum load capacity of your bicycle.
CLEANING YOUR ESCOOTER:
Basic cleaning information and maintenance guide.
Do not use a pressure washer to clean your eScooter. eScooters are not built to withstand high pressure water jets. Using a pressure washer
at full power has the potential to damage parts and can force excess water, dirt, and debris into places it shouldn’t be in and wreak havoc on the
workings of the e scooter.
Do not use special car cleaner and soaps on an eScooter as most car soaps have wax in them which are not suitable for eScooters.
Typically, the best way to wash e scooter accessories is to wipe them down with a dry rag. Avoid getting any water or soap on the following parts:
The hub bearing (the center of the wheel)
The bottom bracket (where the pedals connect together through the frame)
The headset bearing (where the handlebars connect to the frame)
The brake pads and rotor, or discs
Chains, gears and motor
The first step when it comes down to how to wash an eScooter is to use a brush to clean the dry dirt from the rims and tyres of your e scooter. After
that, take a wet rag or sponge and wipe down the frame of your eScooter. Make sure to get to the underside of the frame where dirt is most likely to
gather. Once your eScooter has been thoroughly cleaned, rinse off all the dirty water. After the dirt residue has been cleaned from the eScooter use
a clean, dry rag to wipe the scooter dry.
Once you’ve wiped the scooter dry, lube the chain to prevent it from rusting. To do this, take your chain and run it through a clean dry rag to wipe off
any water that managed to get on it. Next, take chain lube and apply a slow but steady stream to the inside of the chain as you rotate the cranks until
the whole chain got lubed.
Bearing lubrication
The next maintenance step is to lubricate the bearings. Your bearings are the connection between the rotating wheels of your scooter and the
non-rotating frame that holds them stable. As you use your scooter, the friction can cause the bearing to get worn out - we prevent it from happen-
ing by lubricating it regularly.
Start by cleaning the bearings using with a clean and wet towel, you can spin the wheel at the same time which might make it easier for you to
clean. After your bearings are clean, it’s really important for you to add lubricant to the bearings, if you don’t they will get worn very rapidly.
Spray the lubricant generously. Spray directly at the bearings and in the general bearing direction, since they are sealed for better protection. Spin
your wheel at the same time to make sure the lubricant is dispersed effectively.

17
DAXYS BANDICOOT - USER MANUAL
TROUBLESHOOTING:
Troubleshooting information, fault codes, etc
Quick troubleshooting steps:
1. Make a note of the event description;
2. Switch off the system;
3. Visually check for any obvious cause;
4. Solve any easy and obvious cause, if safely possible (e.g. re-connect
the wire connectors of various parts).
Switch the system back on.
If the issue is solved:
1. Normal use may be continued.
2. Schedule a service check at an authorised dealer.
If the issue returns, repeat step 1-4.
If the issue persists:
a) Quit riding.
b) Contact authorised dealer for diagnose and repairs.
If any of the errors appear repeatedly, please contact supplier or
authorised service.
Other common possible issues:
1. eScooter cannot be turned on.
a) Check if the battery has run out of power;
b) Check if the battery switch is on;
c) Check if the display wire is connected well, and try a re-plug check;
d) Use a multimetre to check if the battery discharges normally;
2. eScooter cannot be charged normally.
a) Check if the AC and DC plug of the charger connects properly;
b) Check if the charger light is on after connecting to the power source,
and swap check the charger if possible;
c) Check if the battery is working normally;
3. Headlight is not working when switched on
a) Check if the headlight wires are well connected or damaged;
b) Check if the headlight wires are well connected with the controller;
c) Check if the headlight switch works well, and if the headlight icon is lit
on the display;
4. Riding range drop
The range on one charge strongly depends on several circumstances,
such as (but not limited to):
a) The total vehicle weight including the rider, passengers and cargo
loaded onto the scooter;
b) Weather conditions, such as ambient temperature and wind;
c) Road conditions, such as elevation and road surface;
d) Scooter conditions, such as tyre pressure and maintenance level;
e) Amount of charge and discharge cycles;
f) Age and condition of the battery pack;
g) Scooter usage, such as acceleration and shifting;
h) Assist level(s) used;
Note: Please contact an authorised dealer for further diagnose and
repairs.
Error message User action
E1 / F1 Brake error. Check the brake cable
connection.
E2 / F2 Throttle error. Check throttle wire and
throttle position.
E3 Communication error. Check the con-
nection between handlebar and battery
controller cable
E4 Over current protection. Check the
brake wires.
E5 Under voltage protection. Test with
another battery. Might require a new
battery.
E6 Over voltage protection. Avoid sudden
braking / acceleration, should return to
normal after battery level drops.
E7 Motor sensor error. Test with another
motor. Might require a new motor.
E8 Motor phase lost. Check the wiring.
E9 Controller error. Test with another han-
dlebar. Might require a new controller.
Note: F1/F2 errors appear during start-up self diagnosis.

18
F.A.Q’S:
1. So, how fast can you go on an eScooter?
In AU, an eScooter must have a motor with a maximum power of 250W, assisting the eScooter to a maximum speed of 25 km/h to be road-legal.
2.Can you get any exercise out of an eScooter?
The answer is that you can decide if you want to exercise with an eScooter. There are several options to challenge yourself physically if you want to.
1. You can use your eScooter without any support or in Eco mode and still feel your legs burn.
2. You can do several laps on the same ride.
3. You can ride farther and longer with an eScooter.
4. On your eScooter you are encouraged by the speed/fun factor, and you can keep going.
5. If you weren’t riding an eScooter or regular scooter before, what would you be doing otherwise? We encourage you to get as much exercise as
you want with your eScooter.
And… If you prefer, you can simply have a good time and enjoy the ride without any sweat.
3. Can I handle the eScooter when the battery runs out?
eScooters are enhanced by our motor technology, which provides support on the most challenging terrain. But if the battery runs out, no worries,
you can still puse it as a normal push scooter. Will it be easy? That depends on what terrain you are riding. Empower yourself to ride your eScooter
even when the battery runs out.
4. How far can I expect to ride on a single battery charge?
The range for a single battery charge can vary greatly depending on conditions such as the combined weight of the rider and cargo; wind resistance;
tyre pressure and tread profile; terrain and elevation changes; road or trail surface; outdoor temperature; maintenance of the eScooter; and the
condition of the battery. Please refer to the spec sheet of the eScooter you prefer for the typical range.
5. What is the charging temperature range of eScooter batteries? Why can’t charge in high temperature or low temperature environment?
The eScooter battery charging temperature range is -10~40° C, The battery pack BMS will be automatically protected and cannot be charged if the
temperature is too high or too low. When temperature returns to the required range charging function will return to normal. In this case, there is no
need to report for repairs.
6. How often should I do general maintenance?
We recommend doing maintenance to your scooter every 6 months to make sure all of the components are working properly. Below you can find the
steps to perform a basic maintenance of your Daxys Bandicoot Kickscooter. A tune up consists of the following steps:
- Tire pressure check
- Bearing lubrication
- Suspension lubrication
- Brake adjustment
- Screw tightening
You will need a few things to get these done, all of them can be purchased at a local hardware store.
- Tire pump w/ pressure gauge
- Jig-a-loo lubricant (or any other lithium grease in spray format)
- Brake pads
- Basic toolkit
These are low cost items that, if used regularly, can make your scooter last dramatically longer. In other words, they’re an investment definitely worth
making.