Dentsply Sirona X-Smart IQ User manual

X-SMART IQ™
Getting Started Guide

1 Package Contents
Image Uneditable
Getting Started
Guide
Charger
Assembly
Rubber plugs and
protective case opener
Protective
sleeve barrier
Spray nozzle
(used for lubrication)
Contra-angle
Motor handpiece
Motor handpiece
support and case

Accessibility AssistiveTouch
A
B
C
D
2iPad® set-up
E
Settings Bluetooth
Settings Wi-Fi
Settings Sounds
GeneralSettings
SearchApp Store
If you do not already have an Apple ID, follow the procedure on the
“http://www.apple.com/support/appleid/” website.
Set the volume to maximum
Activate the AssistiveTouch feature
The AssistiveTouch feature allows to emulate the iPad Home button which is not
accessible when in the protective case.
Activate the Bluetooth®
The connection between the motor handpiece and the application
is done via Bluetooth®.
Bluetooth®
Activate the Wi-Fi
Wi-Fi is necessary to download the application from the Apple Store®.
Select the Wi-Fi network and enter your password to connect the iPad.
Wi-Fi
Download the application from the Apple Store®

3Protective Handpiece Case Setup
A B
Need new images and copy
Insert copy about protective sleeves?
copy correct?
Separate the motor handpiece
cover from the motor
handpiece support.
Enclose the iPad mini™in the protective
case and place the rubber plugs on the
camera and the charging port.
Install the motor handpiece case as protective case holder.
C

Wait a few seconds until the application detects the motor handpiece.
When the motor handpiece is connected, the icon changes
and the Bluetooth®LED stops blinking.
Check the motor handpiece serial number and click on the
corresponding number on the iPad screen.
Open the application.
Press the multi-funtion button and check that the Bluetooth®
blue LED is blinking.
A
B
C
D
E
4 Pairing the Motor Handpiece to the App

Access to user
data and logout
Consult and edit
treatment reports
Start Treatment
Adjust torque and
speed parameters
Enable or disable the
auto-reverse function
Motor handpiece
calibration
Consult the file library and
create or edit file sequences
Select your file sequence
(or file system)
Visualize the torque that
was applied to the file
5Application

Bluetooth®connection between the iPad
and the motor handpiece (signal power)
Motor handpiece level
of battery
Access to the stand-alone mode
selection (see next page)
User Manual
Access to Parameters
(volume, language, etc.), Statistics and
Information
Start and Record Treatment Create or select
a patient record
number
Stop recording the
treatment and send a
PDF report by e-mail
Enter treatment data
(notes, working lengths,
last file used, obturation
method)
Select your file sequence
(or file system)
Visualize the torque that
was applied to the file

A
B
AAAAA
Continuous rotation
mode LED status.
Reciprocating motion
mode LED status.
Motor START/STOP
button.
iPad mini™/ motor handpiece
Bluetooth®connection
LED status.
Battery charge
LED status.
Multifunction button
The multifunction button provides the
following functions:
• Pair the motor handpiece to the
application via Bluetooth®.
• Wake up the motor handpiece
(the motor handpiece does not
turn off, it automatically switches
to stand-by mode).
• Select the next file during a
treatment.
Help to identify a problem and
verify the status of the motor
handpiece
From the application tap
on this icon
Select between Continuous
or Reciprocating stand-alone
modes.
Disconnect
the motor
handpiece
Stand-alone Mode
The stand-alone mode allows you to work without the iPad.
After the first connection, if you turn on the motor handpiece without connecting it to the iPad, it
will run with the stand-alone mode settings.
How to set the stand-alone mode
6Motor Handpiece

A
CB
Insert copy about protective sleeves?
Green
On: Charged.
Blinking: Device charging.
Red
On: Low battery.
Blinking: Critical low battery.
Do not use on patient until charged.
Full recharge: 6 hours
Autonomy: 2 days with 8 treatments per
day (= 16 treatments in total).
It is recommended to fully charge the motor
handpiece battery before using the first time.
Do not use any other charger than the one supplied.
Store and charge the motor handpiece
7After use

8Disinfection and cleaning
iPad™Stand
Motor handpiece
Foreword
For hygiene and sanitary safety purposes, the contra-angle must be cleaned, disinfected and
sterilized before each usage to prevent any contamination. This concerns the first use, as well as all
subsequent uses. The use of a protective barrier sleeve is highly recommended.
General recommendations
Do not use chloride detergent materials.
Do not use bleach or chloride disinfectant materials.
Do not spray solution directly on protective case or motor handpiece.
Use only a disinfecting solution which is approved for its efficacy (VAH/DGHM-listing,
CE marking, FDA and Health Canada approval) and in accordance with the DFU of the
disinfecting solution manufacturer.
When subjecting the motor handpiece to a wipe-down disinfection, ensure that the
charging cable is not connected and that the charging socket is closed.
Do not spray cleaning solutions directly on the motor handpiece.
Do not spray cleaning solutions directly on the stand.