Denver DVBT-16 User manual

DVB-T PLAYER
Before connecting, operating or adjusting this product,
please read this user's manual carefully and completely.
Operating Manual
Digital Set Top Box
DVBT-16

Table of Contents
1
Safety Precautions
If any of the following situation arises, get the equipment checked
by a service technician:
1.The equipment has been exposed to moisture.
2.The equipment has been dropped and damaged.
3.The equipment has obvious sign of breakage.
4.The equipment has not been working well or you cannot get it
work according to User¡¯s Manual.
Always read the safety instructions carefully
Keep this User s Manual for future reference
Keep this equipment away from humidity
Lay this equipment on a reliable flat surface before setting it up.
Do not stand it on soft furnishings.
Warning
To prevent the risk of electric shock, do not open the cover or the
back of the receiver.
Do not block the ventilation holes of the device. Leave appropriate
gap above and around it to allow for adequate ventilation.
Do not place the device in an unventilated cabinet or on top of a
unit which emits heat.
Copyright Statement
No part of this publication may be reproduced in any form by any
means without the prior written permission. Other trademarks or
brand names mentioned here in are trademarks or registered
trademarks of their respective companies.
Disclaimer
Information in this document is subject to change without notice.
The manufacturer does not make any representations or warranties
(implied or otherwise) regarding the accuracy and completeness of
this document and shall in no event be liable for any loss of profit or
any commercial damage, including but not limited to special,
incidental, consequential, or other damage.
Before Use(Continued)
Introduction
Safety Precautions
This DVB-T player is a Free-To-Air digital terrestrial receiver,
allowing you to access free-to-air digital terrestrial TV channels and radio
broadcasts.Its digital reception covers VHF & UHF band.
Compared with the analog TV programs, digital TV programs eliminate
the noise and interference but offer high quality video and audio. An on-
screen initial installation guide is provided so that you can easily start to
enjoy watching the programs. In addition, a fully featured remote
controller is included that offers you access to every feature with a simple
press of a button.
Features
1.Bandwidth of 7/8MHz supported
2.Automatic/manual channel search
3.COFDM demodulator
4.Supports remote control
5.NTSC/PAL converting automatically and manually
6.EPG (Electronic Program Guide) and Teletext function
7.Multiple-language OSD (English, German,Portuguese Swedish, Danish
and Spanish)
8.Channel edit, moving and deletion
9.Parental lock control
10.SDTV only
11.Supports subtitle
12.ETSI EN 300 744 DVB-T Compliance
Contents
P1
Before Use(Continued)
P1
Table of Contents
Safety Precautions P1
P2-P3
Identification of Controls
P3
Chapter 2-1 First Time Installation
P3-P8
Chapter 2-2 Initial OSD Setting
P8-P9
Chapter 2-3 Convenient Functions

IN ANT OUT
VCR SCART TV SCART
DIGITAL AUDIO
SERVINGS
AC IN~
Identification of Controls
Main Unit
2
ON / OFF BUTTON
(Used to switch the set
top box on and off)
UP DOWN CHANNELS
(Used to change channels
with out using the remote
control)
DVB WORKING INDICATOR
(Used to visually show when
the set top box is turned on)
REMOTE CONTROL SENSOR
(Used to receive the signal
from the remote control)
(This socket
connects to your
external aerial)
RF IN
(This socket connects
to a coaxial socket
on your surround
sound system)
COAXIAL
(This is used to
connect to your
mains supply)
MAINS CABLE
(This socket connects to
either your tv or video)
RF LOOP THROUGH
(This socket connects to
either a video or dvd)
VCR SCART
(This socket
connects your tv)
TV SCART
(This socket is only used
by the manufacturer and
service personnel)
SERVICE
ON/OFF Button
(used to switch the set top box on and off)
Mute Button
(used to turn the sound on or off)
STANDBY
TELETEXT
TV FORMAT
Numeric Buttons
(used to select channel numbers)
Subtitle Button
(used to switch subtitles on and off)
INFO Button
(used to display information for the channel being viewed)
Recall Button
(reverts to previous channel)
Digital TELETEXT Button
(used to open the interactive digital text)
Exit Button(used to return to the TV)
Pause (used to pause the programme)
LANGUAGE(used to set OSD language
Audio language teletext language)
Favourites Button
(used to open the Favourites menu)
DTV/VCR
(used to switch between DIGITAL TV and video)
TV Format Button
(used to change the TV picture aspect)
Menu Button
(used to open and close the menu windows)
Electronic Programme Guide(used to open and close the EPG)
Audio (used to set the sound output)
TV/Radio(used to switch between
TV and radio stations)
OK
OK Button
(used to confirm a selection within a menu)
Channel up/up direction
Channel down/down direction
Volume decrease/left direction
Volume increase /right direction
Volume decrease /left direction
Channel down/down direction
DTV/VCR

Insert the battery
Refer to the drawing, take the back cover of the remote control off
and remove the empty battery receptacle.
Prior to shipping, a separating film was applied to the battery.
Remove this film.
Insert the battery into the receptacle and insert the receptacle into
the remote.
For the best results,aim the remote towards at the player, receiving
window. Stay within 15 feet and angles of 60 degrees or less.
Under normal use the battery will last for one year.
Remove battery during storage or when you are not using the DVD
player for a long time.
Identification of Controls
*To return to the MAIN MENU
---Press EXIT button.
*To finish the setup operation
---Press MENU to exit from Main Menu screen.
Chapter 2-1 First Time Installation
First Time Installation
No channels are stored in your
unit. AFirst Time Installation
Wizard will appear automatically
on the screen. Continue with the
OSD (On-Screen-Display) to do
the following setting.
1 A First Time Installation Wizard appears. Press¡° ¡± to
select¡°YES¡±.
2 Press¡° ¡± button / ¡° ¡± button to select the item you
wish to set up, and then press ¡° ¡±button / ¡° ¡±button to
switch to your preferred setting.
3Press¡° ¡±button / ¡° ¡±button /¡° ¡±button /
¡° ¡±button to select ¡°NEXT¡±, and then press¡° ¡±to
continue to the next page.
4 To start Auto Search, press¡° ¡± to select ¡°YES¡±.
All the receivable programs (including TV and Music) will be
listed respectively on the screen.
This process may take a few minutes to be done.
5 After Program Search is done, press¡° ¡±button / ¡°
¡±button to select and start watching TV programs.
3
Chapter 2-2 Initial OSD Setting
Main Menu
Most of the Settings of your DVB player can be done by following
the OSD instructions (*Main Menu). For details on how to set up
by using your remote control, please refer to Chapter 5: Remote
Control Guide.
In Advance:
Press MENU to display the Main Menu.
Chapter 2-2 Initial OSD Setting-continued
A. Program List
A-1 TV Program Editing
Before editing your TV program, make sure you have finished with
program search, which should be done by completing the First Time
Installation Wizard. If not, you have to set up your TV programs first.
Please refer to ¡°Program Search¡± for details.
1 Under Main Menu, press¡° ¡± to select ¡°Program List¡±.
2 Under Program List, press¡° ¡±to select ¡°TV Program List¡±.
3 A Program edit table Window appears. You can use this table to edit
your Favorite TV Programs, re-arrange your TV program numbers and
delete the TV programs you dislike.
*To return to the MAIN MENU
---Press ¡°EXIT¡±button.
*To finish the setup operation
---Press MENU to exit from Main Menu screen.
A-2 Music Program Editing
Before editing your music program, make sure you have finished with
program search, which should be done by completing the First Time
Installation Wizard. If not, you have to set up your TV programs first.
Please refer to ¡°Program Search¡± for details.
1Under Main Menu, press¡° ¡±to select ¡°Program List¡±.
2 Under Program List, press¡° ¡± to select ¡°Music Program
List¡±.
3 A Program edit table Window appears. You can use this table to edit
your Favorite TV Programs, re-arrange your TV program numbers and
delete the TV programs you dislike.
*To return to the MAIN MENU
---Press¡°EXIT¡±button.
*To finish the setup operation
---Press MENU to exit from Main Menu screen.
The following is the overview of the seven settings:
Program Search
Automatic Search
Manual Search
Program list
Program search
Parental control
System setting
Game(not for sale)
Accessory
Personal style
MAIN MENU
Program List
TV Program List
Music Program List
Sort
1
2
Enter parental PIN
Enter PIN
OK
3
System Setting
TV standard
Display TYPE
Video output
Antenna power
Regional setting
Language
Time setting
System schedule
4
Game
GAME
Mine
Tetris
Gomoku
Calender
5
Displ ay T y pe
Sc art Ou tput
Ant enna Po wer
Count r y
OSD L anguage
P arent al Cont ro l
P erso nal St yl e
T r ansp arency L evel
Bo rd er P atter n
En t r y A n i mation
Menu Color BLUE
P erso nal St yl eP erso nal St yl e
Ri g ht
R ound
6
ACCESSORY
System Information
Factory Default
System update
6
7
OK
OK
OK
OK
OK
OK
OK

Chapter 2-2 Initial OSD Setting-continued
Pr ogram edit table
No.
1
2
3
4
5
6
7
8
P r ogr am N ame Favor Move Del
FTV
FTV N
FTV TE S T
TTV -1
TTV -2
ST V
Program edit table
The following table is present in the TV
Program Editing and Music Program Editing
menus. You may freely set your favorite
program list, switch program numbers, and
delete an existing program.
Pr ogram edit table
No.
1
2
3
4
5
6
7
8
Pro gram Name Favor Move Del
FT V
FT VN
FT VTES T
TT V-1
TT V-2
STV
Favorite Program Setting
Step 1. In the Program edit table, press ¡° ¡±button / ¡° ¡±
button to highlight ¡°Favor¡± (Favorite Program) section.
Step 2. Under ¡°Favor¡± section, press ¡° ¡±button / ¡° ¡±
button to highlight the corresponding box of your favorite Program and
press¡° ¡± .You will see a ¡°Heart¡± icon appear on this box,
representing that this program is added to your Favorite Program list.
Step 3. Repeat Step 2 to add more favorite TV programs.
In Advance:
a. You can set up your Favorite Program by using remote control.
b. You can press ¡° ¡±button / ¡° ¡±button to step through
your Favorite Program only after one or more Favorite programs are set
up.
*To return to the MAIN MENU
---Press ¡°EXIT¡±button.
*To finish the setup operation
---Press MENU to exit from Main
Menu screen.
Pr ogr a m edit table
No.
1
2
3
4
5
6
7
8
P r ogr am N ame Favor Move Del
FT V
FT VN
F T VT EST
TT V-1
TT V-2
STV
Switch Program Setting
Step 1. In the Program edit table, press ¡° ¡±button / ¡° ¡±
button to highlight ¡°Move¡± section.
Step 2. Under ¡°Move¡± section, press ¡° ¡±button / ¡° ¡±
button to highlight the corresponding program box you wish to change
and press ¡° ¡±.
Step 3. Press ¡° ¡±button / ¡° ¡±button to highlight the
corresponding program box you wish to exchange, and then press
¡° ¡±You will see a ¡°Double-Arrows¡±icon appear on this box,
representing that 2 program numbers are switched.
Step 4. Repeat Step 2 through Step 3 to switch more programs.
*To return to the the up level MENU
---Press ¡°EXIT¡±button.
*To finish the setup operation
---Press¡°MENU¡±to exit from Main
Menu screen.
Delete Program Setting
Step 1. In the Program edit table, press ¡° ¡±button / ¡° ¡±
button to highlight ¡°Del¡± (Delete) section.
Step 2. Under ¡°Del¡± section, press ¡° ¡±button / ¡° ¡±
button to highlight the corre sponding program box you wish to
delete,and press¡° ¡±.You will see a ¡°Cross¡± icon appear on
this box, representing that the program is deleted.
Step 3. Repeat Step 2 to delete more unwanted programs.
4
Chapter 2-2 Initial OSD Setting-continued
In Advance:
Once the programs are deleted, there is no way to add them back. To
watch those deleted programs, you will need to do Program Search
again. Please note that by doing so, your previous program list will be
replaced.
*To return to the up level MENU
---Press ¡°EXIT¡± button.
*To finish the setup operation
---Press menu to exit from Main Menu
screen.
A-3 TV Program List Sorting Setting
You can use this sorting function to re-arrange your program list in
three different ways.
1Under Main Menu, press¡° ¡±to select ¡°Program List¡±.
2 Under Program List, press¡° ¡±to select ¡°Sort¡±.
3Under Sort, press ¡° ¡±button / ¡° ¡±button to select your
preferred sorting: ¡°By name¡±, ¡°By Service ID¡± or ¡°By Channel
No.¡±, and then press ¡° ¡±.
*To return to the MAIN MENU
---Press ¡°EXIT¡± button.
*To finish the setup operation
---Press MENU to exit from Main Menu screen.
B. Program Search
To Enjoy the high quality of digital TV signals through the Set Top Box,
you have to search for all the available TV program first. This unit
provides you with 2 ways of program search, including Automatic
Search and Manual Search.
B-1 Automatic Search
1Under Main Menu, press¡° ¡±button and¡° ¡± to select
¡°Program Search¡±.
2 Under Program Search, press¡° ¡±to select ¡°Automatic
Search¡±.
3An Automatic Search window appears on the screen. All the
receivable TV/Music programs will be listed respectively in the TV
List/Music boxes below. This process may take several minutes to be
done.
In Advance:
After Program Search is done, you can start watching TV or listening
to Music programs by pressing ¡° ¡± / ¡° ¡±.
OK
OK
OK
OK
OK
OK
OK
OK
OK

2 Enter the 4-digital Pin number and press¡° ¡±to enter
the Parental Control window.
B. Program Search
Chapter 2-2 Initial OSD Setting-continued
B-2 Manual Search
You can locate specific programs by selecting frequency numbers.
1Under Main Menu, press¡° ¡± button and¡° ¡±to select
¡°Program Search¡±.
2 Under Program Search, press¡° ¡± button and¡° ¡± to
select ¡°Manual Search¡±.
3An Manual Search window appears on the screen. Press¡° ¡±
button / ¡° ¡±button to select ¡°Channel Number¡±, and the
corresponding frequency number will show from down below.
4 Press ¡° ¡± button to highlight¡°OK¡±, and press¡° ¡±
In Advance:
Almost all of theprograms are avavilable byAutomatic Search.
OK
OK
C Parental Control
This function allows you to lock the programs that you do not want your
children to view. For example, if you set the selected program to be
locked, then the program can't be watched unless the correct PIN
code is entered.
1Under Main Menu, press¡° ¡±button and¡° ¡±to select
¡°parental control¡±.
3Press¡° ¡±button / ¡° ¡±button and¡° ¡±to select
the preferred Parental Control option.
Program list
Program search
Parental control
System setting
Game(not for sale)
Accessory
Personal style
MAIN MENU
5
Chapter 2-2 Initial OSD Setting-continued
c. Change PIN
You can change the PIN code.
Step 1. Press the numeric button to enter 4-digit old PIN code.
Step 2. Press the numeric button to enter new PIN code.
Step 2. Re-enter new PIN code to confirm it.
*To return to the MAIN MENU
---Press ¡°EXIT¡± button.
*To finish the setup operation
---Press MENU to exit from Main Menu screen.
In Advance:
The default PIN is 8888. You may change your PIN code soon as
you enter this menu.Remember to keep your PIN Code in a
secure place.
The super password is 9999.
b. Parental Setting
Step 1. Press¡° ¡±button / ¡° ¡±button to select the
preferred program.
Step 2. If you want to lock the selected program, press¡° ¡±, a
lock icon appear on the Lock box. Then the selected program is
locked. Press¡° ¡±again if you want to unlock it.
a. Channel Lock
Channel Lock allows the parents to prevent younger members of the
family to watch.Any channel can be ¡°locked¡± so that it cannot be
selected for viewing without a 4-digit PIN code being entered. In this
way, any channel not suitable for younger viewers can be protected.
If you want to lock the current channel you are watching, select ¡°YES¡±
and then press¡° ¡±to lock the channel.
C Parental Control-continued
D. System Setting
This function allows you to set up the normal aspect ratio (picture
display shape) according to source signal and monitor format of your
TV, or your own viewing preference.
D-1 TV Standard
This function enables you to set the TV system format.
D-2 Display Type
This function enables you to set the screen format of the TV set
connected so that those broadcast programs are displayed correctly.
1Under Main Menu, press¡° ¡±button and¡° ¡±to select
¡°System Setting¡±.
2Under System Setting, press¡° ¡±to select ¡°Display
Type¡±.
3Press¡° ¡±button / ¡° ¡±button and¡° ¡±to select
a preferred TV display.
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK

D. System Setting
This function enables you to set the video output.
1.under main menu,press button and to select
system setting
2.under system setting,Press to select video output .
3.press button / button / to set video output.
¡°¡± ¡°¡±
¡°¡±
¡°¡± ¡° ¡±
¡°¡±¡°¡±¡°¡±
To return to the MAIN MENU.
---Press¡°EXIT¡±button.
To finish the setup operation
---Press MENU to exit from main menu screen.
Chapter 2-2 Initial OSD Setting-continued
*To return to the MAIN MENU
---Press¡°EXIT¡± button.
*To finish the setup operation
---Press MENU to exit from Main Menu screen.
b. 4:3 Letter Box
Select ¡°4:3 LB¡± for a conventional size TV set. Black bands appear
at top and bottom of screen (letter-box style).
*Video material not formatted in the pan & scan style is played in the
letter-box style.
Video output
CVBS
RGB
D-2 VIDEO OUTPUT
C. 16:9 Wide
Select ¡°16:9¡± for a wide-screen TV set.
*Played in ¡°FULL¡± size.
Setting the wide-screen TV to ¡°FULL¡± mode is also necessary.
Each screen shows an example when the video material for a wide-
screen is played.
a. 4:3 Pan Scan
Select ¡°Pan & Scan¡± (4:3) for a conventional size TV set.
*Video material formatted in the pan & scan style is played in that
style (the left and right edges are cut off).
Main Menu
Sys t em Set t in g
Di spl ay T y pe
4:4:3 PS3 PS
4:4:3 L3 L BB
16:16:99
System Setting
MAIN MENU
TV standard
Display type
Video output
Antenna power
Regional setting
Language
Time setting
system schedule
Chapter 2-2 Initial OSD Setting-continued
In Advance:
GMT: The current time is set automatically whenever GMT offset
changes.
*To return to the MAIN MENU
---Press ¡°EXIT¡± button.
*To finish the setup operation
---Press MENU to exit from Main Menu screen.
D-4 regional settings
This function allows you to set the time zone of your location and
corresponding bandwidth of the digtial signals all at once simply by
selecting the country you are currently in.
1Under Main Menu, press¡° ¡±button/¡° ¡±button to
select ¡°System Setting¡±.
2Under System Setting, press¡° ¡±button to select
¡°Regional setting¡±.
3Press ¡° ¡±button / ¡° ¡±button/¡° ¡±button select
the country where you¡¯re in.
This function allows you to set the language of your OSD (On-Screen
Display) Menu.
1Under Main Menu, press¡° ¡±button/¡° ¡±button to
select ¡°System Setting¡±.
2Under System Setting, press¡° ¡±buttonto select ¡°OSD
Language¡±¡°1st Audio language¡±¡°2st audio language¡±¡°DVB subtitle¡±
3 Press¡° ¡±button / ¡° ¡±button and¡° ¡±to select
the preferred OSD language.Audio language / DVB subtitle language.
D-5 OSD Language/Audio Language/Teletext language
*To return to the MAIN MENU
---Press ¡°EXIT¡± button.
*To finish the setup operation
---Press MENU to exit from Main Menu screen.
1 Under Main Menu, press
2 Under System Setting, press
3Press
¡°¡±button and¡° ¡±to select
¡°System Setting¡±.
¡°¡±to select ¡°Antenna
Power¡±.
¡°¡±button / ¡° ¡±button/¡° ¡±button to
initiate antenna power.
D-3 Antenna Power
If you are using passive Antenna Power, set Antenna Power to
¡°OFF¡±; if you are using active Antenna Power, set Antenna Power to
¡°ON¡±.
System Setting
MAIN MENU
TV standard
Display type
Video output
Antenna power
Regional setting
Language
Time setting
system schedule
System Setting
MAIN MENU
TV standard
Display type
Video output
Antenna power
Regional setting
Language
Time setting
system schedule
System Setting
MAIN MENU
TV standard
Display type
Video output
Antenna power
Regional setting
Language
Time setting
system schedule
6
Regional Setting
England
English
GMT+08:00
Country
OSD Language
Time Zone
Language
OSD language English
1st Audio language English
2st Audio language English
DVB subtitle English
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK

*To return to the MAIN MENU
---Press¡°EXIT¡± button.
*To finish the setup operation
---Press MENU to exit from Main Menu screen.
In advance: Audio language / DVB subtitle is not avaliable on all
channels.
D-6 OSD Language/Audio Language/Teletext language
Task1 Active
Task2 Inactive
Task3 Inactive
Task4 Inactive
Task5 Inactive
Task6 Inactive
Schedule
Mode once
Start Date 2004/01/01
Start Time 00:00
End Time 00:00
Channel Type TV
Channel No 0001
Detail
Press¡° ¡± ¡° ¡± button and use numeric button to set the
information.
To return to the main menu
---Press¡°EXIT¡±button.
To finish the setup operation
---Press MENU to exit from main MENU screen.
This function allows you setting the time:
1:Under main menu,press¡° ¡±button and¡° ¡±button to
select¡°system setting¡±.
2:Under system setting,press¡° ¡±button to select¡° Time setting¡±
3:You can set time by pressing¡° ¡±¡° ¡±/numeric button.
OK
D-7 Time setting
Time setting
GMT usage ON
Time zone GMT TO 0:00
Chapter 2-2 Initial OSD Setting-continued
Task1 Active
Task2 Inactive
Task3 Inactive
Task4 Inactive
Task5 Inactive
Task6 Inactive
Schedule
Mode once
Start Date 2004/01/01
Start Time 00:00
End Time 00:00
Channel Type TV
Channel No 0001
Detail
You can set power on/off time and program schedule in system
schedule:
D-8 system schedule
1:Under main MENU,press¡° ¡±button and¡° ¡±button to
select¡°system setting¡±.
2:Under¡°system setting¡±,press¡° ¡±button to select
¡°system schdule¡±.
3:Press¡° ¡± ¡° ¡± button to select Task.
4:Press¡° ¡± ¡° ¡± button to inactive/active this task.
5:Press¡° ¡±button to enter in task detail setting.
6:Press¡° ¡± ¡° ¡± button to select setting item.
System Setting
MAIN MENU
TV standard
Display type
Video output
Antenna power
Regional setting
Language
Time setting
system schedule
*To return to the MAIN MENU
---Press ¡°EXIT¡± button.
In Advance:
By pressing <Game> button, you can enter Game mode.
E. Game
This section provides you bonus games for extra fun and enjoyment.
D-1 Game selecting
1Under Main Menu, press¡° ¡±button and¡° ¡±button to
select ¡°Game¡±.
2Press¡° ¡±button/¡° ¡±button to select one game to play.
7
Chapter 2-2 Initial OSD Setting-continued
F2 Factory Default
This function allows you to erase the previous/current OSD setting
and to restore Factory Default setting.
1Under Main Menu, press ¡° ¡±button and¡° ¡±button to
select¡°Accessory¡±.
2Under ¡°Accessory¡±, press¡° ¡±and¡° ¡±button to select
¡°Factory Default¡±.
3Press¡° ¡±button/¡° ¡±button to enter the Factory
Default window.
Accessory
4Press¡° ¡±button and¡° ¡±button to select ¡°YES¡± to
go back to Factory Default setting.
*To return to the MAIN MENU
---Press ¡°EXIT¡± button.
*To finish the setup operation
---Press MENU to exit from Main Menu screen.
*To return to the MAIN MENU
---Press ¡°EXIT¡± button.
*To finish the setup operation
---Press MENU to exit from Main Menu screen.
F1 System Information
This function allows you to view the version number of the system.
1Under Main Menu, press¡° ¡±button and¡° ¡±button
to select ¡°Accessory¡±.
2Under Accessory , press¡° ¡±button to select
¡°System Information¡±.
Program list
Program search
Parental control
System setting
Game(not for sale)
Accessory
Personal style
MAIN MENU
F. Accessory
This feature allows you to set extra functions
Program list
Program search
Parental control
System setting
Game(not for sale)
Accessory
Personal style
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
Program list
Program search
Parental control
System setting
Game(not for sale)
Accessory
Personal style
Accessory

Chapter 2-2 Initial OSD Setting-continued
G-2 Transparency Level
This function allows you to set the level of transparency of your OSD
menu frames.
1Under Main Menu, press¡° ¡±button and¡° ¡±button
to select¡°Personal Style¡±.
2 Under Personal Style, press¡° ¡±button/¡° ¡± button
to select ¡°Transparency Level¡±.
3Press¡° ¡±button / ¡° ¡±button to select the preferred
level of transparency from 1 to 8.
*To return to the MAIN MENU
---Press ¡°EXIT¡± button.
*To finish the setup operation
---Press MENU to exit from Main Menu screen.
G-3 Border Pattern
This function allows you to set the border pattern of your OSD (On-
Screen Display) Menu frames.
1 Under Main Menu, press¡° ¡±button and¡° ¡±button to
select ¡°Personal Style¡±.
2Under Personal Style, press¡° ¡±to select ¡°Border
Pattern¡±.
3Press¡° ¡±button / ¡° ¡±button to select the preferred
border pattern.
*To return to the MAIN MENU
---Press ¡°EXIT¡± button.
*To finish the setup operation
---Press MENU to exit from Main Menu screen.
G. Personal Style
This section provides you many additional features to make your OSD
setting more personal and stylish.
G-1 Menu Color
This function allows you to set the colour of your OSD (On-Screen
Display) Menu.
1Under Main Menu, press¡° ¡±button and¡° ¡±button to
select ¡°Personal Style¡±.
2Under Personal Style, press¡° ¡±button /¡° ¡± to select
¡°Menu Color¡±.
3Press¡° ¡±button / ¡° ¡±button to select the preferred
Menu color.
The following is for your selection: blue, red, yellow, orange, green
and gray.
F3 System update
System Information
Factory Default
System update
Accessory
This function is reserved:
Program list
Program search
Parental control
System setting
Game(not for sale)
Accessory
Personal style
MAIN MENU
7
System update
Press Any Key to Exit
Status Timeout,retry 006
Transmission 000%
Burn 000%
8
Chapter 2-2 Initial OSD Setting-continued
*To return to the MAIN MENU
---Press ¡°EXIT¡± button.
*To finish the setup operation
---Press MENU to exit from Main Menu screen.
G-4 Entry Animation
This function allows you to set the entry animation of your ¡°Fast
Preview¡± OSD menu frame.
1 Under Main Menu, press¡° ¡±button and¡° ¡±button to
select ¡°Personal Style¡±.
2Under Personal Style, press¡° ¡± button/¡° ¡±button
to select ¡°Entry Animation¡±.
3 Press¡° ¡±button / ¡° ¡±button to select the preferred entry
animation.
The following is for your selection: Right, Down, Right Down, Blind
Right and Blind Down.
*To return to the MAIN MENU
---Press ¡°EXIT¡± button.
*To finish the setup operation
---Press MENU to exit from Main Menu screen.
G-3 Border Pattern Fast Preview
Chapter 2-3 Convenient Functions
The DVB-T player provides you fast preview of live broadcasts from
each TV channel. You can use this function to take a fast preview at all
the TV programs in advance of watching it in full screen.
1Press¡° ¡±
A TV Channel Menu appears to the left with corresponding live
broadcast of the selected program to the right.
kk
FT V
TT V-1
1
2
4
5
6
7
8
3
FT VN
No. P ro gram Name
TV Program List
2 Press¡° ¡±button / ¡° ¡±button to toggle each TV channel
and to see its live broadcast.
3Press¡° ¡±to watch your preferred program in full screen.
In Advance:
The DVB-T player also provide a Channel Guide window of live
broadcasts in thumbnail images.For details, please refer to ¡°Channel
Guide¡±.
*To exit from this page
---Press¡°EXIT¡± button.
How to select programs
The DVB-T player provides you the following ways to select programs.
* Press¡° ¡±button / ¡° ¡±button to step through the
porgram selection.
*Press numeric button(s) to enter the program number you
want to view.
* Select program from the program list.
* Select program from the Electronic Program Guide (EPG).
7
7
OK
OK
OK
OK
OK
OK

Chapter 2-3 Convenient Functions
Lock
FT V
FT V
TT V-1
1
2
4
5
6
7
8
3
FT VN
No. P ro gra m Name
TV Program List
2004/07/10 00:18
2 Press¡° ¡±button to more digital teletext provided by the
selected channel.
Press¡° ¡±button and ¡°EXIT¡±button to return to program list.
In Advance:
The content of digital teletext varies according to the program provider.
It could be pictures and sound for the program, pages of information on
the programs, the weather, the news or other options.
Some channels provide only digital teletext that carry no normal TV
program; if so, you can¡¯t see the preview of the channels with EPG
function.
3Press¡° ¡±button / ¡° ¡±button to toggle through each TV
channel and to see its live broadcast.
4Press¡° ¡±to watch your preferred program in full screen.
*To exit from this page
---Press¡°EXIT¡± button.
Displaying Information of the Program
Press <INFO.> during playback, and the corresponding
information of the program will appear on the screen.
Audio Channel
You can select the preferred audio channel and sound mode.
1Press <Audio> , the Audio Channel window appears on the
screen.
2 Press¡° ¡±button / ¡° ¡±button to select ¡°Channel¡± or
¡°Sound Mode¡±.
3Press¡° ¡±button / ¡° ¡±button to select the preferred audio
channel or sound mode.
When the ¡°Channel¡± option is changed, the value of ¡°Audio PID¡±
will also change to the correct value.
*To exit from Audio channel
---Press <Audio> button again.
EPG (Electronic Program Guide)
The DVB-T player provides you an Electronic Program Guide to take a
fast preview of live broadcasts from each TV channel in advance of
watching it in full screen.
1Press <EPG> .
An Electronic Program Guide Menu appears on the screen, with a TV
channel menu to the left and corresponding live broadcast of the
selected program to the right.
Digital T eletext
kk
FT V
TT V-1
1
2
4
5
6
7
8
3
FT VN
No. P ro gra m Name
TV Program List
1 1
9
Chapter 2-3 Convenient Functions-continued
Language setting
Digital Teletext
If the program you are watching broadcasts digital teletext, the DVB-T
player can display teletext.The content of digital teletext varies
according to the program provider. It could be pictures and sound for
the program, pages of information on the programs, the weather, the
news or other options.
Favorite PR (Favorite Program)
There are some channels that you tend to watch more often and some
only occasionally. Favorite PR allows the most-watched channels to
access more easily, leaving less watched channels acces-sible but
out of way.
Music mode
*To exit from this page
---Press <INFO.> button.
Press <Teletext> button, the teletext window appear on the
screen.
*To exit from teletext
---Press <EXIT> button to exit from teletext.
Switch DTV and VCR you can press the ¡°¡¡¡¡¡± button to switch the
DVB output and VCR out.
* Please note: The VCR signal from other set(DVD,VCR,etc.)
connected to the ¡°VCR SCART¡± in the back panel and only support
¡°CVBS¡± signal.
Press
¡°Fav on¡± appears on the screen, and the favorite program is
activated; by pressing ¡° ¡±button / ¡° ¡±button, you can
only step through the favorite programs. Other programs can still be
accessed by entering the program number.
*To exit from Favorite Program
---Press button until ¡°Fav off¡± appears on the
screen.
The DVB-T player provides you the convenient function to listen to the
digital radio.
1Press <TV/Radio> button to switch between TV channel
and Music channel.
Wait a few seconds, it will switch from TV mode to Music mode.
Press button, turn over the teletext information.
Press¡°¡¡¡¡¡±,you can set the OSD language / Audio language / DVB
subtitle.
PAUSE MODE
You can freeze the picture in TV. Press¡°¡¡¡¡¡±,again,exit pause status.
*To exit from Music mode
---Press <TV/Radio> button again.
Switch TV and VCR
OK
DTV/VCR
TELETEXT

Power Supply
Input Voltage 90-240V AC 50Hz.
Power Consumption Maximum 10W
Decoder
Video Formats SD,4:3/16:9 Switchable.
Audio Format MPEG Layer I&II,32/44.1/48Khz.
Video Output CVBS ,RGB(default)
Connection
Main Power Cable Fixed Type.
Tuner 1 Antenna Input/1 RF Output.
Scart 1 for VCR/1 for TV(Loopthrough).
SPDIF 1 Coaxial.
Technical Specification
ALL RIGHTS RESERVED, COPYRIGHT DENVER ELECTRONICS A/S