Design Within Reach Cove 100168796 User manual

1 | WWW.DWR.COM | 1.800.944.2233 | DESIGN WITHIN REACH STUDIOS
Cove Canopy Bed
Designed by Nathan Yong for Design Within Reach
Customer Service:
1.800.944.2233 inside the U.S.
1.203.614.0600 outside the U.S.
Wood Care
Dust with a slightly damp, soft,
lint-free cloth. Wipe dry with a
dry, soft cloth in the direction of
the wood grain. Do not use aerosol
cleaners or polishes. Also, do not
use polishes containing waxes
or abrasives, or polishes that are
oil-based.

2 | WWW.DWR.COM | 1.800.944.2233 | DESIGN WITHIN REACH STUDIOS
Cove Canopy Bed
Hardware Checklist
ALLEN WRENCHELECTRIC DRILL (OPTIONAL TOOL)MALLET (REQUIRED TOOL)
STEP STOOL (OPTIONAL)
LONG BOLT X 2
(M6 X 55MM)
MEDIUM BOLT X 84
(M6 X 30MM) MACHINE SCREW X 8
L-BRACKET X 2 PUNCH BLOCK X 1

3 | WWW.DWR.COM | 1.800.944.2233 | DESIGN WITHIN REACH STUDIOS
Cove Canopy Bed
Parts Checklist
HEADBOARD PANEL X 1
FOOTBOARD LEG X 2HEADBOARD LEG X 2
FOOTBOARD PANEL X 1
SHORT TOP RAIL X 2SIDE RAIL X 2

4 | WWW.DWR.COM | 1.800.944.2233 | DESIGN WITHIN REACH STUDIOS
Cove Canopy Bed
Parts Checklist
LONG TOP RAIL X 2
SLAT X 42 CENTER LEG X 2
CENTER RAIL X 1

5 | WWW.DWR.COM | 1.800.944.2233 | DESIGN WITHIN REACH STUDIOS
Repeat process for footboard and other short top rail. Use parts labels as a guide to make sure rounded edges of footboard and rail face eventual
mattress area. Firmly seat joints with punch block and rubber mallet.
2.
Stand headboard leg upright and attach headboard panel, making sure its rounded top edge faces eventual mattress area. Repeat with other headboard
leg. Attach short top rail to headboard legs using labels to ensure that rounded edge of rail faces toward eventual mattress area. Firmly seat joints with
punch block and rubber mallet.
1.
Cove Canopy Bed
Note: Minimum three people recommended for assembly. To ensure proper assembly, join matching letters on parts labels.

6 | WWW.DWR.COM | 1.800.944.2233 | DESIGN WITHIN REACH STUDIOS
Cove Canopy Bed
Using a step ladder as necessary, connect either long top rail to legs, as shown, making sure rounded edge of rail faces inward as indicated on parts
labels. Repeat with other long top rail. Use punch block to firmly seat connections.
4.
Position headboard and footboard assembly as near as possible to final location of bed. Install first side rail, connecting side-rail hooks into
corresponding slots in legs, making sure rounded top edge faces inward. Repeat with other side rail. Use punch block to seat all joints.
3.

7 | WWW.DWR.COM | 1.800.944.2233 | DESIGN WITHIN REACH STUDIOS
Cove Canopy Bed
Connect center legs to center rail using long bolts, then attach center rail to L-brackets on headboard
and footboard using machine screws. Use adjustable feet on center legs to level center rail.
6.
Attach L-brackets to headboard and footboard using machine screws, threading all loosely before tightening with Allen wrench.
5.

8 | WWW.DWR.COM | 1.800.944.2233 | DESIGN WITHIN REACH STUDIOS
Cove Canopy Bed
Top View
Attach slats as shown using short bolts. Thread all loosely at first, then tighten snugly with Allen wrench or electric drill fitted with hex bit.
8.
Before proceeding to next step, ensure bed frame is square by measuring from a headboard leg kitty-corner across bed to opposite footboard leg,
as shown by dotted line. Then measure the distance to other set of legs and compare. Adjust bed frame until two X measurements are equal or
nearly equal.
7.