Design Within Reach GATHER TABLE 100062673 User manual

The GATHER TABLE
Designed by Jacob Plejdrup
ASSEMBLY INSTRUCTION

2 3
ASSEMBLY INSTRUCTION
Due to the size and weight of the components the assembly requires two people.
Tools needed
Rubber mallet
Large, clean, protective material such as a blanket or tarp.
PARTS LIST
24 x Short screw, Torx 30 head
8 x Long screw, Torx 30 head
12 x Short wooden dowel
8 x Long wooden dowel
5 x Metal pin
4 x Connecting screw
1 x Allen wrench
1 x Torx 30 wrench
1 x Bit TX30 for screwdriver
4 x Felt pad
TABLE PARTS
2 x Table leg
2 x Cross beam
2 x Leg bar
2 x Tabletop Halves
24x 8x 12x 8x 5x 4x 1x 1x 1x 4x
2x 2x 2x
2x

2 3
1
Lay tabletop halves on protective material with undersides facing up. Insert five metal pins in one table half, then
slide other half onto pins.
2
Insert four short wooden dowels into predrilled holes on underside of tabletop.

4 5
3
Insert long wooden dowels into predrilled holes in leg, then fit leg bar onto dowels and tap in with rubber mallet.
Insert long screws in predrilled holes in center of leg bar and tighten with Torx wrench or screwdriver. Repeat with
second leg assembly.
4
Orient leg assembly as shown and install connecting screws. Repeat with second leg assembly.

4 5
5
Insert short wooden dowels in ends of cross beams and tap in with rubber mallet.
6
Attach cross beams to first leg assembly and tighten connector cams with Allen wrench. Repeat process with
second leg assembly to complete table base.

6 7
7
Lift table base onto table top and fit onto dowels installed in previous step.
8
Attach base to tabletop with 24 short screws using Torx wrench or screwdriver. Use a piece of thick paper
or cardboard as protection material to avoid damages of the legs. Retighten the connector cams when fully
assembled.

6 7
9
Leveling glides may be adjusted after table is turned over and put in place.
10
Optional felt pads may be attached

8 MB
CARE AND CLEANING INSTRUCTIONS
General care
• Avoidexposingtodirectheatandsunlightwhichcancausecrackingandcolorchanges(somewoodscan
darken and some can fade).
• Colorchangesmayalsooccurwhenobjectsareleftforextendedperiodsonthesamespotonthefurniture.
• Maintainconsistenthumidityof45–55%inyourhometopreventexcessiveexpansionandcontractionofparts
and joints.
• Wipeupspillsimmediatelywithaclean,drycloth.
• Donotplacehotorhumidobjectsdirectlyonthefurniture,whichmaystainordamageit.
• Usetrivetsforhotpansordishestopreventdamagetonishandunderlyingwood.
• Usecoastersfordrinkstopreventmoisturefromcontactingsurface.
• Keeproughandsharpobjectsawayfromwoodsurfaces.
• Applyprotectivepadstoundersidesofitemsbeingdisplayedonwoodsurfaces.
• Avoidprolongedcontactofrubberfeetorbumpersondisplayeditems,whichcanreactwithanddamagewood
finish.
Cleaning
• Dustfrequentlywithadampcloth,thenwipedry.
• Cleanasnecessarywithaclothmoistenedwithasolutionofmildsoapandwater.Wipedryimmediately.
• Neverpoursoaporwaterdirectlyontothefurnituresurface.
• Donotuseharshchemicalsorabrasivesonanynishes.