Design Within Reach parallel bed standard User manual

1 | WWW. D W R . C O M | 1 . 8 0 0 . 9 4 4 . 2 2 3 3 | DESIGN WITHIN REACH STUDIOS
Parallel Bed: Standard
Designed by Jeffrey Bernett,
Nicholas Dodziuk and Piotr Woronkowicz
Customer Service:
1.800.944.2233 inside the U.S.
1.203.614.0750 outside the U.S.
• INSTRUCTIONS MUST BE FOLLOWED
CAREFULLY TO ENSURE PROPER ASSEMBLY.
• CLEAN CLOTH GLOVES MUST BE
WORN WHEN INSTALLING SLIPCOVERS.
• ASSEMBLY REQUIRES TWO PEOPLE.

2 | WWW. D W R . C O M | 1 . 8 0 0 . 9 4 4 . 2 2 3 3 | DESIGN WITHIN REACH STUDIOS
BED SLAT (x2)
FRAME SLIPCOVER (NOT ILLUSTRATED)
HEADBOARD SLIPCOVER (NOT ILLUSTRATED)
CENTER RAIL
SIDE RAIL (x2)
FOOTBOARDHEADBOARD
Parallel Bed: Standard
Parts List 1/2

3 | WWW. D W R . C O M | 1 . 8 0 0 . 9 4 4 . 2 2 3 3 | DESIGN WITHIN REACH STUDIOS
CORNER LEG BRACKET (x2) SLAT CLIP (x2)
HEADBOARD LEG (x2)
CENTER LEG
EXTRA BOLTS ARE INCLUDED. ELECTRIC DRILL WITH
0.5" SOCKET IS RECOMMENDED.
0.5"SOCKET WRENCH
WASHER (x4)
Parallel Bed: Standard
Parts List 2/2
MEDIUM BOLT – 1.5" (x4)
SHORT BOLT – 1" (x18)

4 | WWW . D W R . C O M | 1 . 8 0 0 . 9 4 4 . 2 2 3 3 | DESIGN WITHIN REACH STUDIOS
Parallel Bed: Standard
1.
x10 SHORT BOLTS
x2 MEDIUM BOLTS
2.
Attach footboard to side rails using corner legs brackets and small L brackets.
Loosely thread all bolts, then tighten down.
Connect center rail to footboard.
x2 WASHERS

5 | WWW. D W R . C O M | 1 . 8 0 0 . 9 4 4 . 2 2 3 3 | DESIGN WITHIN REACH STUDIOS
Attach legs to headboard.3.
Parallel Bed: Standard
Loosely attach both side rails to headboard, then tighten bolts.4.
x4 SHORT BOLTS
x4 SHORT BOLTS

6 | WWW. D W R . C O M | 1 . 8 0 0 . 9 4 4 . 2 2 3 3 | DESIGN WITHIN REACH STUDIOS
Parallel Bed: Standard
Screw center leg into center rail, then bolt center rail onto headboard.5.
x2 WASHERS
Align seams of headboard slipcover with headboard, then pull down
and secure with velcro along bottom edge.
6.
CLEAN CLOTH GLOVES MUST
BE WORN DURING THIS STEP.
x2 MEDIUM BOLTS

7 | WWW. D W R . C O M | 1 . 8 0 0 . 9 4 4 . 2 2 3 3 | DESIGN WITHIN REACH STUDIOS
Parallel Bed: Standard
Roll out slat assemblies onto frame. Lift center and push
down to ensure snug fit. Install slat clips near headboard
and footboard to secure slat system.
8.
7.
CLEAN CLOTH GLOVES MUST
BE WORN DURING THIS STEP.
Use snap to align bottom-right corner of frame slipcover, then secure
with velcro starting at footboard and working up side rails to headboard.
Make sure slipcover is pulled tightly
all the way to headboard and covers
all parts of side rails.