DeVilbiss iGo User manual

iGo Travel
Concentrator
QUICK GUIDE
SYMPTOM ACTION
Unit does
not operate
when button
is pressed
• Press power button and
hold for 1 second
• Plug into External Power or
install charged battery
• Connect to DC or AC
power supply
• Contact Intermountain
Homecare & Hospice
Unit does
notoperate
External
Power light
flashes with
audible alert
Power Fail Alert
is activated
• Check the cannula connection
• Ensure the tubing is not kinked
• Reposition cannula in nose
• Replace cannula with
shorter tubing
• Remove humidifier
• Use continuous flow
delivery for patients that
fail to trigger equipment
Yellow light
indicates
lowoxygen
• Clean air filter and make
sure nothing is blocking
the concentrator exhaust
Red light
indicates unit
has overheated
• Move the concentrator to a
cooler location and allow to cool
• Clean the air filter and make
sure nothing is blocking the
concentrator exhaust
No Breath
Detected
lightflashing
• Disconnect cannula — if
flow is restored, clean
or change cannula
• Ensure all cannula connections
are tight, and it fits
comfortably in your nose
• Replace with shorter cannula
Power Fail Alert • Recharge battery
• Install battery or plug
into external power
© 2015 Intermountain Healthcare. All rights reserved.
The content presented here is for your information only. It is not a substitute
for professional medical advice, and it should not be used to diagnose or
treat a health problem or disease. Please consult your healthcare provider if
you have any questions of concerns. More health information is available at
intermountainhealthcare.org. Patient and Provider Publications 801-442-2963
HC003-09/15
iGo™Travel Concentrator
Troubleshooting
Content created and approved by
Intermountain Homecare & Hospice
Unlocking the Flow Rate
If for some reason you are unable to change the
flow rate, please follow the instructions below.
1 Connect the AC adapter to the unit
and to a suitable AC source. The green
External Power light will illuminate.
2 With the unit OFF, press and hold the
Mode Select button for 5 to 6 seconds.
Theunit will “chirp” when the unlocking
takes affect.
3 Verify that the lock is inactive by turning
the unit ON and attempting to change the
flow rates using the Flow Rate Setting plus
and minus buttons. If the lock is inactive,
the flow rate lights will change.
If the flow rate lights do not change,
turn the unit OFF and repeat the
unlocking procedure from step 2.
4 When the flow rates are unlocked, turn
the unit OFF and remove power.
Concentrator
parts
oxygen
outlet port
control
panel
Concentrator &
Travel Case
AC Power Supply
DC Power Supply

Set the flow mode
1 Press the flow mode button to select the
continuous or PulseDose flow.
2 Please select flow rate and flow mode
according to your prescribed setting.
DONOT change setting without
consultingyour physician.
• Continuous flow mode — The Flow
Indicator light illuminates continuously
inthis mode.
• PulseDose mode —The Flow Indicator
light pulses with every breath in this
mode. An alert will beep after 30 seconds
if a breath is not detected. If another 60
seconds elapses and no breath is detected,
the unit will switch to continuous flow at
the last continuous flow setting used.
Connect the
oxygen tubing
1 Attach the oxygen tubing
tothe oxygen outlet.
a. Use only standard
nasal cannula when
in
PulseDose mode.
2 Fit the nasal cannula.
Plug in the power cord
or insert battery
AC Power Supply
1 Insert the AC power supply cord
into the External Power Receptacle
on the left side of the device.
2 Plug the AC power supply cord into
a grounded AC outlet.
3 The battery lights and the
External Power Indicator
willlight up on the control panel.
DC Power Supply
1 Start your vehicle.
2 Insert the DC power supply cord securely
into the External Power Receptacle
on the right side of the device.
3 Insert the plug into the DC power
outlet in your vehicle (the fuse rating
must be 15 AMP or greater).
4 The External Power Indicator
will light up on the control panel.
5 Secure the concentrator and the DC adapter
in your vehicle and make sure the air inlet
and exhaust vents are not blocked.
Note:
• Do not run more than 2 Lpm continuous
oxygen when connected to the DC power
supply to avoid draining the battery.
• Do not leave the concentrator or DC adapter
plugged into the vehicle without the engine
running or attempt to start the vehicle while
the DC adapter is connected to the vehicle.
Battery
The iGo will charge the battery any time AC
power is present and the battery temperature is
below a safe charging temperature. If external
power is disconnected, the iGo will automatically
switch over to the battery. When external AC
power is restored, the iGo will accept power from
the external source and charge the battery.
Charging the Battery
The typical time to recharge a battery from a
fully discharged condition is up to 4 hours.
Turn on the
concentrator
1 Press and hold the on/off
powerbutton for 2 seconds.
All control panel lights will
illuminate briefly with an audible alert.
Set the flow rate
1 Press the + or – button to select
your prescribed flow rate.
ESTIMATED NEW BATTERY
OPERATION TIME
Setting Continuous PulseDose
14.0 hours 5.4 hours
22.4 hours 4.7 hours
31.6 hours 4.0 hours
4N/A 3.5 hours
5N/A 3.2 hours
6N/A 3.0 hours
iGo™Travel Concentrator