DeVilbiss DV51 Standard cpap series User manual

DV51 STANDARD CPAP SERIES
EN
DeVilbiss®IntelliPAP® Positive Airway Pressure Device
CAUTION–USA Federal law restricts this device to sale by, or on the order of a physician.
Assembled in USA of US & Imported Parts. Instruction Guide.
ES
Dispositivo de presión positiva en las vías respiratorias
IntelliPAP®de DeVilbiss®
PRECAUCIÓN–La ley federal de EE. UU. limita la venta de este dispositivo a médicos o a personas que dispongan
de la correspondiente orden médica.
Montaje efectuado en EE. UU. con piezas fabricadas en EE. UU. e importadas. Guía de instrucciones.
FR
Appareil de ventilation spontanée en pression positive IntelliPAP®
de DeVilbiss®
ATTENTION–En vertu de la loi fédérale américaine, cet appareil ne peut être vendu que par un médecin ou sur
ordonnance de ce dernier.
Assemblé aux États-Unis avec des pièces des États-Unis et des pièces importées. Guide d’instructions.

EN - 2
A
10 4
6
2
78
B
5 3
Key Features
1
2
6
4
3
5
7
C
2
3(bottom) 6
1
4
5
7
D
5
1
4
2
6
3(bottom)
7
E
1
2
DV51/DV5HH
DV5HH
1
5
2
6
3
7
4
8
910 11
F

EN - 3
EN ENGLISH................................................................................................ EN-3
ES ESPAÑOL ............................................................................................... ES-19
FR FRANÇAIS.............................................................................................. FR-36
TABLE OF CONTENTS
Symbol Definitions............................................................................................................................................... EN - 4
Important Safeguards.......................................................................................................................................... EN - 4
Introduction.......................................................................................................................................................... EN - 5
Intended Use ............................................................................................................................................. EN - 5
Indications for Use..................................................................................................................................... EN - 5
Contraindication......................................................................................................................................... EN - 5
Key Features....................................................................................................................................................... EN - 5
IntelliPAP Device ....................................................................................................................................... EN - 5
Keypad ...................................................................................................................................................... EN - 5
Humidifier Cradle....................................................................................................................................... EN - 5
Water Chamber ......................................................................................................................................... EN - 5
Therapy Management System .................................................................................................................. EN - 5
System Assembly................................................................................................................................................ EN - 5
Without Heated Humidification.................................................................................................................. EN - 5
With Heated Humidification....................................................................................................................... EN - 6
Keypad and Display ............................................................................................................................................ EN - 6
Operation............................................................................................................................................................. EN - 6
Start-Up ..................................................................................................................................................... EN - 6
Using the Comfort Delay Feature.............................................................................................................. EN - 6
Controlling the Humidity ............................................................................................................................ ER - 7
Shut Down................................................................................................................................................. EN - 7
Enable Menu List....................................................................................................................................... EN - 7
SmartCode®and Adherence Score Information........................................................................................ EN - 7
Patient Messages................................................................................................................................................ EN - 8
Reminders ................................................................................................................................................. EN - 8
Notifications............................................................................................................................................... EN - 8
IntelliPAP Travel Information ............................................................................................................................... EN - 8
IntelliPAP DC Operation ...................................................................................................................................... EN - 8
Battery Power............................................................................................................................................ EN - 8
Supplemental Oxygen......................................................................................................................................... EN - 9
Accessories/Replacement Items......................................................................................................................... EN - 9
Maintenance........................................................................................................................................................ EN - 10
Cleaning .............................................................................................................................................................. EN - 10
Troubleshooting................................................................................................................................................... EN - 11
Specifications ...................................................................................................................................................... EN - 12
Guidance and Manufacturer’s Declaration.......................................................................................................... EN - 14
Advanced Control Menus.................................................................................................................................... EN - 16

EN - 4
SYMBOL DEFINITIONS
Class II electrical protection-double insulated Type BF equipment-applied part
Data port input/output Standby-turns blower on/off
Next item on LCD display Increase value on LCD display
Previous item on LCD display Decrease value on LCD display
Attention, consult accompanying documents Heat
DC input: 12 VDC, center pin positive 100-240 VAC input 50/60 Hz
Locked Unlocked
IPX1 Drip-proof, vertical Delay-starts the delay cycle
This device contains electrical and/or electronic equipment that must be recycled per EC Directive 2002/96/
EC-Waste Electrical & Electronic Equipment
IMPORTANT SAFEGUARDS
READ ALL INSTRUCTIONS BEFORE USING
THIS DEVICE.
SAVE THESE INSTRUCTIONS.
DANGER
• ElectricShockHazard – Do not use while bathing.
• ElectricShockHazard – Do not immerse this device into water or any other liquid.
• ElectricShockHazard – Do not attempt to open or remove the cabinet. There are no user-serviceable internal
components. If service is required, return the product to your home care provider. Opening or tampering with the
product will void the warranty.
WARNING
• The DeVilbiss IntelliPAP should be used only with masks recommended by DeVilbiss, your physician or respiratory
therapist.
• To avoid rebreathing of exhaled air, do not use a CPAP mask unless the device is turned on and providing a supply
of air. Venting in the mask should never be blocked. When the device is turned on and providing a fresh supply of
air,exhaledairisushedoutofthemaskvent.However,whenthedeviceisnotoperating,exhaledairmaybe
rebreathed. Rebreathing of exhaled air for longer than several minutes can in some circumstances lead to
suffocation. This warning applies to most CPAP devices.
• The DeVilbiss IntelliPAP is not a life support device and may stop operating with certain device faults or with a power
failure. It is intended to be used on spontaneously breathing individuals weighing 66 lbs/30 Kg or greater.
• To avoid electric shock, always unplug power cord from wall outlet power source when performing cleaning.
• Use only accessories recommended by DeVilbiss.
• Alwaysremovethewaterchamberfromtheoptionalhumidiercradlebeforelling.
• Ifwaterhasspilledontothehumidiercradleorithasbeensubmergedintowater,unplugpowercordfrompower
source immediately. Allow device to dry completely before use.
• Neverblockairopeningsofthehumidiercradleorchamber.Donotinsertobjectsintoanyopeningsortubes.
• Forproperoperation,placesystemonaat,sturdy,levelsurface.
• Theoptionalhumidierisintendedforsingle-patientuseonly.
• Ifthesystemisplacedontheoor,donotpositionitwhereitmaybesteppedonwhengettingoutofbed.
CAUTION
• The circular data port connector located on the back of the IntelliPAP is used to attach accessories to the device.
The connector must only be used with accessories approved for use by DeVilbiss. Do not attempt to attach any other
device to this connector as it may damage the CPAP or the accessory device.

EN - 5
• Never rinse or place the device in water. Never allow liquids to get into or around any of the ports, switches or air
lter;doingsowillresultindevicedamage.Ifthisoccurs,discontinueuseandremovethepowercordfromthe
power source. Allow the device to completely dry before use.
• DonotplacetheIntelliPAPwhereitcanbeknockedontotheoororwherethepowercordmaycreateatriphazard.
• OnlytheDeVilbissDV5seriesHeatedHumidiersystemisrecommendedforusewiththeIntelliPAP.Other
humidiersystemsmaypreventthedevicefromdetectingsnoringandmaycauseinappropriatepressurelevelsin
the mask.
• Emptyanddryhumidierwaterchamberbeforetransporting.
INTRODUCTION
Intended Use
The DeVilbiss IntelliPAP Model DV51 Series Standard is intended for use in treating OSA in spontaneously breathing
patients 30 Kg (66 lbs) and above by means of application of positive air pressure. The device is to be used in home and
clinical environments.
Indications For Use (Optional Heated Humidifier)
Use on the advice and prescription of a licensed physician to help relieve the symptoms of dryness of the throat, nasal
passages and the mouth, which are common with positive airway pressure therapy. This is especially true in dry climates
and during the cold season when humidity in the air is typically lower than at other times.
Contraindication
Do not use IntelliPAP system if your upper airway has been bypassed.
NOTE–Symptoms of dryness of the throat, nasal passages, and the mouth are common with positive airway pressure
therapy. The IntelliPAP features an optional humidier system to help minimize these effects.
KEY FEATURES
DeVilbiss IntelliPAP Device (Figures A
and B)
1. Keypad/LCD Display (see Figure C)
2. Air Supply Port on Back
3. AirSupplyPortonBottom(foroptionalhumidier)
4. Air Supply Port Plug
5. HeaterPowerConnector(foroptionalhumidier)
6. AC Power Connector
7. DC Power Connector
8. Data Port
9. Power Cord (appropriate to your wall outlet) (not
shown)
10. Air Inlet Filter Opening
11 Connector Cover (not shown)
Keypad (Figure C)
1. On/Off
2. Previous Item
3. Next Item
4. Delay
5. Decrease Value
6. Increase Value
7. Heater PowerLED(foroptionalhumidier)
Ask your equipment provider for information about other
DeVilbiss masks, equipment, and accessories.
Humidifier Cradle (Figure D)
1. Heater Plate
2. Heater Power Connector
3. Storage Compartment for Connector Cover (on
bottom)
4. Air Supply Port Inlet
5. Air Supply Port Outlet
6. Flow Generator Release Button
7. Flow Generator Locking Tabs
Water Chamber (Figure E)
1. Chamber Lid
2. Chamber Base
3. Heat Transfer Plate (on bottom)
4. Sealing Gasket
5. Water Level Indicators (front and sides)
6. Chamber Release Latch
7. Chamber Disassembly Lever
Therapy Management System (Figure F)
1. SmartLink®(optional)
SYSTEM ASSEMBLY
Without Heated Humidification
1. Locate the air supply port and heater power connector on the bottom of the IntelliPAP device. Ensure that each
opening has the appropriate soft cover securely attached.
2. Place the IntelliPAP on a stable surface such as a nightstand or table. If you wish, you may also place the device on
theooratthebedside,beingcarefultoplacetheunitwhereitwon’tbekickedorsteppedon.Ensurethattheair
inlet in the back of the device is not blocked by anything such as curtains or bedding.
NOTE–Never place the IntelliPAP system on a soft surface such as a bed or couch during operation.

EN - 6
With Heated Humidification
CAUTION–The height of the IntelliPAP must be lower than the mask when using a humidier to prevent water from getting
into mask.
1. Ifyoursystemincludesahumidier,pleasefollowstepsinFigures1-7.
a. Remove the air supply tubing from the back of the device.
b. Locate the air supply port at the bottom of the device. Remove the port plug and insert it into the air supply
port in the back of the device.
c. Locate the heater power connector on the bottom of the device. Remove the connector cover and insert it into
thestorageopeninginthebottomofthehumidiercradle.
KEYPAD AND DISPLAY
Basic CPAP Controls
Name Symbol Function
ON/OFF TheON/OFFbuttonstartsandstopstheowofairfromthedevice.
HEATER 

IfyourIntelliPAPhasaheater/humidierattached,thesebuttonsadjusttheheatersetting.
Increase the setting for more humidity and decrease the setting for less humidity.
DELAY
The Delay button activates the comfort delay feature and only functions if this feature has been
enabled. To understand how to set the parameters of this feature, please refer to the Using the
Comfort Delay Feature found on page EN - 6.
NOTE– The left and right arrow keys on the control panel provide access to menus for specic settings. Ask your
homecare provider for more information.
OPERATION
1. Fully insert the power cord into the back of the device. Plug the other end of the power cord into the AC wall outlet.
2. Attach air supply tubing to air supply port in the back of the device.
3. Prepare the mask (supplied by your equipment provider) by referring to the mask’s instruction guide.
4. Connect the air supply tubing to the mask.
NOTE–The air supply tubing supplied with the device is specially designed to prevent kinking and allow you to receive
optimal airow. Use only the 22 mm diameter, smooth-bore, kink-resistant tubing supplied with this device or an air supply
tubing recommended by your equipment provider.
Start-up
Put on your mask and press the ON/OFF button on the keypad OR put on your CPAP mask and take a few breaths to turn
onairowautomatically.Thepressureinyourmaskwillrisetothesetpressureinabout10seconds.
NOTE–If the device does not automatically start after taking 2-3 breaths, this feature may have been disabled. If Auto ON/
OFF is disabled, you must manually press the ON/OFF button to start and stop the device.
The keypad display shows the actual mask pressure while the device is in use. Because this is the actual pressure, the
device pressure reading may vary slightly as you breathe.
IfyourDeVilbissIntelliPAPsystemincludesahumidier,itsheatercontrolsandstatusaredisplayed.
NOTE– If the display on your device is not similar to those listed above, refer to the section titled “Patient Messages” on
page EN-8.
Using the Comfort Delay Feature
YourIntelliPAPhasacomfortdelayfeaturetohelpmakeiteasierforyoutofallasleep.Theairowwillstartatalow
pressureandthengraduallyramp-uptotheprescribedsettingoverthelastfewminutesofthespecieddelaytime.
NOTE–When the delay comfort feature is activated, a message will ash on the display periodically, indicating the amount
of time remaining in the delay.
You can adjust the amount of time spent in comfort delay by using the advanced device controls. The Delay Time can be
adjusted from 0 to 45 minutes in 5-minute increments.
NOTE–If you are unable to change the delay time, your provider has locked this setting.
Pressthedelaybuttontoactivatethecomfortdelayfeature.Theairowpressurewilldroptotheprescribedcomfortdelay
pressure.

EN - 7
Inthenal10minutesofthedelayperiod,thepressurewillgentlyrisetothepressureprescribedforyourtherapy.You
mayrepeatthecomfortdelaybypressingthedelaybuttonagainifyouhavenotfallenasleepduringtherstuse.
Controlling the Humidity (optional)
The heater setting can be adjusted within a range of 1 to 10. The optimum temperature setting is dependent on the ambient
temperature and humidity of your room. If your room temperature is low and/or the relative humidity is high, then a lower
temperature setting may be necessary to prevent excess condensation in the air supply tubing. If the room temperature is
high and/or the relative humidity is low, then a higher temperature setting may be necessary for optimum comfort.
The heater setting of 1 results in a heater plate temperature of approximately 84°F (29°C). The heater setting of 10 results
in a heater plate temperature of approximately 149°F (65°C).
NOTE–Always allow at least 10 minutes of cooling time after turning the device off before removing the water chamber
from the humidier cradle.
WARNING
Donotattempttollthehumidierwhileitisattachedtothehumidiercradle.Damagetothehumidiercradle
mayoccur.
CAUTION–Use only distilled water that is at room temperature. Do not add any medication or other additives to the water.
CAUTION– For proper operation, ensure the ow generator is OFF before inserting humidier chamber.
WARNING
Nevertouchtheheaterplateonthehumidiercradle.Nevertouchtheheattransferplateonthebottomofthe
waterchamber.Theseplatescanreachtemperaturesashighas149°F(65°C)duringoperation.
Donotoperatetheheaterifthewaterchamberisempty.Theheaterplatemaybeturnedoffusingthekeypad
heatercontrolwhenbeingusedwithoutwater.
Shut Down
Press the ON/OFF button to turn the device off. You may also simply remove your mask. After a few seconds the device
willdisplaythemessage“MaskOff.Pleasecheckmaskt.”Ifyoudonotputthemaskonagainthedevicewill
automatically turn off in about 20 seconds. Pressing any button will remove the message from the display.
NOTE–If the DeVilbiss IntelliPAP does not turn off automatically, the Auto-OFF feature may have been disabled. In this
case you must manually turn the device off.
Enable Menu List
The Enable menu is available in all modes and is a sub-menu that allows you to control various functions of your IntelliPAP.
Itisaccessedbypressingthedownbuttonwhile“EnableMenu”isshownontheDisplay.
DisplayExample EnableMenuItemDescription
Auto-OFF 
Enabled
ThisoptioncontrolstheAuto-OFFfeature,whichautomaticallystopstheowofair
after taking off the mask. The device will require at least 30 seconds to turn OFF
depending on the kind of mask used. When Auto-OFF is enabled, Auto-ON is also
enabled. If the unlocked symbol is shown, you are able to adjust this setting. If the
locked symbol is shown, this setting can only be adjusted by your provider.
Auto-ON 
Enabled
ThisoptioncontrolstheAuto-ONfeature,whichautomaticallystartstheowofair
after breathing once or twice into the mask. This is always enabled when Auto-OFF is
enabled. If the unlocked symbol is shown, you are able to adjust this setting. If the
locked symbol is shown, this setting can only be adjusted by your provider.
LowBacklight
Enabled
Low backlight Enable will keep the backlight dim during operation. Low backlight
Disabled will turn the backlight OFF during operation.
ExitMenu
Press
Pressing the up key exits the Enable menu.
SmartCode and Adherence Score Information
Your homecare provider may contact you to retrieve SmartCode and Adherence Score information. To display the
SmartCode, press the LEFT arrow key once. Use the UP arrow or DOWN arrow keys to change the SmartCode reporting
period. Press the LEFT arrow key again to display the Adherence Score.

EN - 8
PATIENT MESSAGES
Your IntelliPAP will alert you of issues that may require some action on your part in order to make your therapy more
effective. You can press any key or button to clear the message from the display, but the IntelliPAP will operate normally
evenifthemessageisnotcleared.Twokindsofmessagesaredisplayed:RemindersandNotications.
Reminders
Reminders alert you when parts of your system need to be replaced. Some components of your system wear over time
and, if not replaced, may compromise your therapy. If you see a message on the display that is not listed below, you may
have the optional DeVilbiss SmartLink®Module attached to your device, which provides additional messages. Refer to the
documentation that was provided with the SmartLink Module.
CleanFilter–Theltershouldbecheckedevery10daysforsignsofdirtorwearsothatitcanbecleanedasneeded.
This message helps to remind you to check it regularly.
Notifications
NoticationsidentifyconditionsinyourIntelliPAPthatmayrequireactionbyyouoryourequipmentproviderinorderto
maintain a high level of therapy. If you see a message on the display that is not listed below, you may have the optional
DeVilbiss SmartLink Module attached to your device, which provides additional messages. Refer to the documentation that
was provided with the SmartLink Module.
DelayRunningxxMinutesLeft–Whileacomfortdelaysessionisactive,thismessageisashedonthedisplayevery5
seconds to let you know how much time is left in the delay.
MaskOff–Thismessageappearsduetoapoormasktoraremovedmask.Checkforleakaroundthemasksealand
make adjustments as necessary according to the mask manufacturer’s instructions. This message will be displayed until
thehighairowproblemiscorrected.Ifthehighairowconditionpersistsforabout20seconds,thedevicewill
automatically turn off if Auto-OFF is enabled.
DeviceFault – If a device fault message is displayed, refer to Troubleshooting for instructions.
INTELLIPAP TRAVEL INFORMATION
International Power Changes
Your DeVilbiss IntelliPAP is approved for sale and use in North America and is equipped with a universal power supply that
it is automatically capable of accepting line voltages of 100 to 240V~ 50/60Hz. You do not need to make any adjustments
to the device if you are traveling to another country where the line voltage is different than your domestic line voltage.
Simply contact your equipment provider for the correct style power cord for the region in which you will be traveling (refer
to Accessories/Replacement Items for the correct part number).
Altitude
Your IntelliPAP automatically compensates for changes in altitude between sea level and 9000 ft (2750 m). You do not
need to make adjustments to the device for changes in altitude.
INTELLIPAP DC OPERATION
Battery Power
Your IntelliPAP can be operated from a 12V DC power source in a motor home, boat or other recreational vehicle. The
power source can be used with a 12V DC power cord or a 12 V DC stand-alone battery. Both parts are available from your
equipment provider (refer to Accessories/Replacement Items for the correct part numbers). Both accessory cables are
required for stand-alone battery operation. The stand-alone battery connection uses clamps that attach to the terminal
connections of the battery.
NOTE–The heater for the IntelliPAP’s humidication system will not operate directly from a 12V DC power source. If you
need humidication, non-heated humidication is still available. Alternately, instead of connecting12V DC power directly to
the IntelliPAP, you can pass the DC power through an inverter that will deliver AC power to the system. This will allow the
heater to function. The power rating of the inverter must be at least 200 watts @ 110V~ / 400 watts @ 220V~.
NOTE–The IntelliPAP will automatically switch power sources between AC and 12V DC if both sources are available. If
your unit is connected to both AC and 12V DC power sources, it will operate on AC power as long as AC power is present,
and automatically switch to 12V DC power if AC power is lost. When AC power is restored, it will return to the AC source.
You do not need to reset or adjust any settings when the power source switches, but remember that your heater will not
operate on 12V DC.

EN - 9
SUPPLEMENTAL OXYGEN
WARNING-OXYGEN USE
• Oxygen supports combustion. To avoid possible physical injury, do not smoke while using this device with
supplementaloxygen.Donotusethisdevicenearhotobjects,volatilesubstancesorsourcesofopenames.
• Always turn on the IntelliPAP before turning on the oxygen source. Turn off the oxygen source before turning off the
IntelliPAP.
• Thisdeviceisnotsuitableforuseinthepresenceofaammableanestheticmixture.
• Ataxedowrateofsupplementaloxygen,theinhaledoxygenconcentrationwillvarydependingonthepressure
setting, patient breathing pattern, mask selection, and leak rate. This warning applies to most types of CPAP devices.
• Never allow the oxygen source to run continuously while connected to the IntelliPAP if the device is not in use. If the
IntelliPAPisnotbeingused,turnofftheoxygenow.
CAUTION
• Oxygen is a prescribed gas and should only be administered under the supervision of a physician.
• Theowsettingoftheoxygensourcemustbespeciedbyaphysician.
Supplemental oxygen is sometimes prescribed in addition to CPAP for treatment of Obstructive Sleep Apnea. If your
physician prescribed oxygen for your sleep therapy, you can add the oxygen in one of two ways:
1. Obtain the optional oxygen adapter (part #7353D-601) from your homecare provider and connect it to the air supply
port on the IntelliPAP. Connect one end of the air supply tubing to the open end of the adapter and the other end of the
air supply tubing to the mask.
2. If your mask is equipped with an oxygen port, your physician may request that you apply oxygen directly to your mask.
ACCESSORIES/REPLACEMENT ITEMS
Replacement Items
Air-inletlter(4/pk) DV51D-602 Heater connection cover DV51D-605
Fineparticlelter(4/pk) DV51D-603 Oxygen adapter 7353D-601
Air supply tubing (6’) DV51D-629 Carrying case DV51D-610
Air supply plug DV51D-604 HeatedHumidier DV5HH
HumidierChamber DV5C Chamber Sealing Gasket DV5C-614
Power Items
AC power cord (USA) DV51D-606 DC power cord DV51D-619
AC power cord (Brazil) DV51D-612 DC battery clamp-on adapter (requires DC
Power Cord DV51D-619) DV51D-696
DeVilbiss Masks RecommendedforusewithSleepCube
FlexSet®Masks Serenity®Masks
Large, Silicone 9354L Large, Silicone 9352L
Medium, Silicone 9354D Medium, Silicone 9352D
Small, Silicone 9354S Small, Silicone 9352S
Medium, Gel 9354G Medium, Gel 9352G
Small, Gel 9354GS Small, Gel 9352GS
Large, ComfortTouch™Silicone 9354LR Large, ComfortTouch Silicone 9352LR
Medium, ComfortTouch Silicone 9354DR Medium, ComfortTouch Silicone 9352DR
Small, ComfortTouch Silicone 9354SR Small, ComfortTouch Silicone 9352SR
Medium, ComfortTouch Gel 9354GR Medium, ComfortTouch Gel 9352GR
Small, ComfortTouch Gel 9354GSR Small, ComfortTouch Gel 9352GSR
EasyFit®Nasal Available in Silicone (S, M, L, XL), Gel (S, M, L) or SilkGel (S, M, L). Contact
your equipment provider
EasyFit Full Face Available in Silicone (S, M, L, XL), Gel (S, M, L) or SilkGel (S, M, L). Contact
your equipment provider

EN - 10
MAINTENANCE
DANGER
Electricshockhazard-Donotattempttoopenorremovethecabinet;therearenouser-serviceablecomponents
inside.Ifserviceisrequired,contactyourequipmentproviderforinstructionsonobtainingservice.Openingor
attemptingtoserviceyourdevicewillvoidthewarranty.
WARNING
Disconnectsupplybeforeservicing.
PressureAccuracy–The IntelliPAP is designed to provide accurate pressure performance from the factory without
additional calibration. No routine service is required provided the device is used in accordance with the manufacturer’s
directions.
NOTE–Some countries require periodic servicing and calibration of this kind of medical device. Contact your equipment
provider for further information.
StandardAir-InletFilter–Checkthelterevery10daysandcleanitifnecessary.Replacethelterevery6monthsor
soonerifitisdamaged.Thestandardlterisdesignedtolterparticleslargerthan3.0micronsinsize.TheIntelliPAP
MUSThavethestandardlterinplaceduringoperation.
OptionalFineParticleFilter–Checkthelterevery10daysandreplaceitifitisdirtyordamaged;otherwisereplacethe
lterevery30days.Theoptionalneparticlelterisdesignedtolterparticlesassmallas0.3micronsinsize.
CLEANING
WARNING
Toavoidelectricshock,alwaysunplugthepowercordfromthewalloutletpowersourcebeforecleaning.
CAUTION–Never rinse or place the device in water. Never allow liquids to get into or around any of the ports, switches or
air lter; doing so will result in product damage. If this occurs, do not use the device. Contact your equipment provider for
service.
Device Cabinet
1. Unplug the IntelliPAP from the power source. Wipe the cabinet with a clean, damp cloth every few days to keep the
cabinet dust free.
2. Allow the device to dry completely before plugging it into a power source.
Filters
Air-InletFilter
1. Theair-inletltershouldbecheckedevery10daysandcleanedasnecessary.Thelterislocatedintherearofthe
device.
CAUTION–Proper lter function is important for the operation of the device and to protect the device from damage.
2. Toclean,removethedarkouterfoamlterfromtheframe.
3. Washthelterinasolutionofwarmwateranddishwashingdetergent,andrinsewithwater.Allowtheltertodry
completely.Ifthelter(part#DV51D-602)isdamaged,contactyourequipmentproviderforareplacement.
4. Ensurethelteriscompletelydrybeforeinstallationanduse.
FineParticleFilter(Optional)
1. Ifyouhaveanoptionalneparticlelter(part#DV51D-603),inspectthislterandreplaceitifitshowssignsofdirtor
damage. Do not wash.
2. Installtheneparticlelterbehindthestandardlter.
NOTE–If the ne particle lter is not installed rst according to the directions, the life of the lter will be reduced requiring
more frequent replacement.
Optional Heated Humidifier
WaterChamber-Humidierwaterchambershouldbecleaneddaily.
1. Press on the chamber release latch and pull out the water chamber from the cradle (Fig 4).
2. Separate the chamber halves by pressing forward on the chamber disassembly lever and lifting the lid of the
chamber (Fig 9).
3. Remove the sealing gasket from the chamber lid (Fig 10).
4. Wash the parts in a solution of warm water and mild diswashing detergent.