DEVOLA DVC1500W User manual

Wall Mounted Panel Heater
Operating Instructions
Model
1.5kW Panel Heater
2.0kW Panel Heater
FOR INDOOR USE ONLY
BEFORE INSTALLING OR USING THIS PRODUCT
THE INTRUCTIONS SHOULD BE READ CAREFULLY
Save this booklet for future reference
WARNING! To reduce the risk of fire, electric shock, or personal injury,
read all the instructions before using this heater.

IMPORTANT SAFEGUARDS
READ ALL INSTRUCTIONS BEFORE USING.
•WARNING: In order to avoid overheating, do not cover the heater.
•This appliance is not intended for use by children or persons with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they
have been given supervision or instruction concerning use of the appliance by a
person responsible for their safety. Children should be supervised to ensure that
they do not play with the appliance.
•If the supply cord is damaged, it must be replaced by the manufacturer, its service
agent or similarly qualified persons in order to avoid a hazard.
•This product was designed to be installed in a residential capacity for indoor use
only. Please do not use the product for any other purpose.
•Do not use this heater in the immediate surroundings of a bath, shower or swimming
pool. If installed in a bathroom then the control panel must be impossible to reach by
persons in the bath/shower.
•The electrical installation must be carried out by a qualified electrician in accordance
with the local regulations.
•The heater is fitted with a length of flexible cable for connection to the fixed wiring of
the premises through a suitable connection box positioned adjacent to the heater.
The supply circuit must encompass a double pole isolating switch with a contact
separation of at least 3mm.
•Never cover or obstruct in any way the heat outlet slots at the top of the heater or
the air inlet slots in the base of the heater.
For your safety, this heater is fitted with a thermal cut-out. In the event that
the product overheats, the cut-out prevents excessive temperatures by
cutting the power to the heater.
WARNING: DO
NOT COVER

WHERE TO INSTALL THE HEATER?
nThis heater is designed to be installed for indoor use only.
nDo not locate the heater below a fixed socket outlet or connection box.
nComply with the minimum clearance distances as indicated in Fig. 1.
nIn humid areas such as bathrooms and kitchens, the connection box must be
installed at least 25cm above the floor.
nDo not install the heater in a draught likely to affect the control setting.
WARNING: the heater must not be installed in zone 1 of the bathroom.
The above sketch is provided for your information only. We advise you to contact a
qualified electrician for guidance.
HOW TO INSTALL THE WALL HEATER?
nThe wall brackets supplied with the heater must be used. The heater should be
positioned observing the minimum clearances stated around the heater – see Fig. 1
nFirst remove the wall bracket from the rear housing. Unscrew the 2 screws located
on the top of the 2 vertical bars of the wall bracket (See Step1). Then pull out the
top bar by pressing firmly both upper parts slotted into the rear housing (see fig 2)
nSlide down the wall bracket in order to remove it from the rear housing. (See fig 3)
nFix the wall bracket securely to the wall through the 4 screw holes provided.
nRaise the heater to upright position; Present the heater and engage 2 slots of the
bottom parts of the wall brackets in the wall heater’s rear enclosure then pull up the
heater. Then engage 2 slots of the upper parts of the wall bracket and tighten the 2
screws in order to lock the device.
STEP 1
STEP 2
STEP 3

OPERATION
Control Panel Instructions
nSymbol instruction
Symbol
Function
ON / OFF
MODE
Mode setting
-
“-“ key
+
“+” key
P
PROG MODE (set the heater with programs)
nHow to use
Turn on the main power by pressing the main switch to “I” position then the
display will flash three times, the LCD screen will display 7.0OC and (Anti-Frost
Mode).
1) MODE SELECTION
When the heater is on, press “MODE” button to cycle between the modes. There are
6 working modes: , , , , , .
- Comfort Mode: User defined temperature between 5°C ~ 35°C
- 1°C below the comfort mode temperature
- 2°C below the comfort mode temperature
- Eco Mode – 3.5°C below the comfort mode temperature
- Anti-Frost Mode – keeps temperature above 7°C
- Controlled by a 7 day user programmable timer

To set the Comfort Mode temperature, press mode until is displayed, then select
the desired temperature by pressing the +/- buttons. Once on the desired temperature,
wait 5 seconds and the “°C” symbol will flash to indicate the temperature is set.
2) PROGRAMMING THE TIMER (P Mode)
Set the mode to . The numbers 1-7 on the top left corner of the display
correspond to days of the week from Monday to Sunday. There are 24 symbols on
the lower half of the display which show the working mode setting for each hour of
the day. The symbols for each working mode are below:
Use the +/- keys to select the weekday. The symbol shows which day is selected,
then press “P” again to confirm the selection.
Now the clock will need setting. The hour digits will flash which can be adjusted using
the +/- keys. Press “P” again to confirm the hour, which will then cause the minute digits
to flash. Use the +/- keys to adjust the minutes and then press “P” again to confirm the
minutes.
Weekday setting from
Monday to Sunday
24 hours
setting
Working mode
setting for each
hour
Time
P7 day
timer mode

Once the time is confirmed, the first segment of the 24 hour symbols will flash,
indicating that the working mode for the first hour of the day (00:00 – 01:00) is being
programmed.
Press MODE repeatedly until the desired working mode symbol is shown for this time
period, then press the + key to continue to the next hour period. Repeat this process
until all 24 hour periods have been set.
Note: There are 4 pre-set 24 hour cycles which can be chosen by holding down
“MODE” for 3 seconds and using the +/- to select P1, P2, P3, P4.
P1# #
From#0#to#6#:#Eco#mode#
From#6#to#9#:#Comfort#mode#
From#9#to#17#:#Eco#mode#
From#17#to#24#:#Comfort#mode#
#
P2# #
From#0#to#6#:#Eco#mode#
From#6#to#9#:#Comfort#mode#
From#9#to#12#:#Eco#mode#
From#12#to#14#:#Comfort#mode#
From#14#to#17:#Eco#mode#
From#17#to#24#:#Comfort#mode#
#
P3#
From#0#to#8#:#Eco#mode#
From#8#to#24#:#Comfort#mode#
#
P4#
From#0#to#8#:#Comfort#-2#mode#
From#8#to#24#:#Comfort#mode#
Press “P” to save these settings for the selected day, and the symbol will move to the
next day. Repeat this programming for all 7 days.
When you finish setting the working mode for one week, press “P” again to go back to
the current working mode and the heater will start to work according to the program you
set.
!

!
MAINTENANCE
1. Before you clean the appliance, switch the heater off and wait until it has cooled
down.
2. Use a damp cloth to wipe off the fan heater housing.
3. Clean the upper and lower grilles of the unit periodically
4. Do not use water, detergents, abrasive cleaning liquids or chemical agents (Alcohol,
Gasoline etc.) to clean the appliance.
5. If the unit or power cord is damaged, stop using immediately and contact your
retailer. Never attempt to dismantle, repair or modify the unit by yourself.
BS PLUG
Wiring Instructions: Should it be necessary to change the plug please note the wires in
the mains lead are coloured in accordance with the following code:
BLUE - NEUTRAL
BROWN - LIVE
GREEN/YELLOW - EARTH
As the colours of the wires in the mains lead of this appliance may not correspond
with the coloured markings identifying the terminals in your plug, proceed as follows:
1. The BLUE wire is the NEUTRAL and must be connected to the terminal that is
marked with the letter Nor coloured BLACK.
2. The BROWN wire is the LIVE and must be connected to the terminal that is marked
with the letter Lor coloured RED.
3. Neither wire is to be connected to the terminal which is marked with the letter E
or earth symbol , coloured GREEN or GREEN/YELLOW.
4. Always ensure that the cord grip is positioned and fastened correctly.
If a 13A (BS 1363) fused plug is used it must be fitted with a 13A (BS 1362) fuse. If in
doubt consult a qualified electrician.
Wiring!for!a!13!Amp!
plug!(BS!1363)!
The!Earth!Terminal!
is!marked!with!the!
letter!E!or!Earth!
Symbol

SPECIFICATION
Voltage 220-240V~ 50Hz
The crossed out Wheelie Bin logo is used to highlight electrical products that should
not be disposed of with normal household waste. Please visit
www.recycle-more.co.uk to find where your nearest recycling point is and recycle this
product at the end of its life. For more information on disposal contact your local
authority.
Customer Services
Devola
97 Walsall Road
Birmingham
B42 1TX
Tel: [phone]
Website: www.devola.co.uk
Version 1/16
Wattage
Net Weight
Gross Weight
Panel Size cm
1.5kW Panel
6.2kgs
7.3kgs
82.1x 11.6x43.7
2.0kW Panel
8.6kgs
10.1kgs
103.2x 11.6x43.7