Dewenwils HOYS16A1 User manual

Please pay attention to the warning signs
Read the instructions with caution before operating
and keep it properly
SKU: HOYS16A1
V20615
[Instruction Manual]
Outdoor Digital Yard Stake Timer

To reduce the risk of fire, electric shock or personal injury, please strictly
follow the instructions.
1. Do not connect any devices which may exceed the maximum ratings of
this timer.
2. Do not immerse in water.
3. Children are not allowed to use the timer without supervision.
4. Do not disassemble or repair the product, but only by authorized service
personnel.
5. Please always unplug and store indoors when not in use.
6. Used bateries should be disposed safely and environmentally.
WARNING:
Installation:
01
As shown in the figure, connect the three sections
together. Be sure to firmly tighten the stake to the
body before installing into the ground.
Tips: If the ground is too hard to insert the stake,
digging a hole that matches the stake with a hard
object will be perfect.

1. Light Sensor: Detects light density to tum the connected devices on or
off.
2. Operating Mode Indicator: Indicates current operating mode.
3. Select Button: To select and switch the operating mode.
4. Overload protection switch: Tum on/off the power manually and overload
protection.
5. Outlets: To plug the lights or devices to be controlled by the timer.
6. Transmitter
Press the overload protection switch to the "l" position and turn on all outlets
first. The indicator on the switch will be lighted.
The yard stake timer can be operated via the included transmitter from up
to 100ft away or manually press the button on the stake to select desired
function. You can choose any one of thefollowing modes:
ON: Power is ON to attached devices. The "power" indicator will be lighted.
Sensor (Dusk - Dawn): Power will tum on at dusk and remain on until dawn
Sensor +2 H/4H/6H/8H: Power will turn on at dusk and off after hours
you selected.
Timer +2 H/4H/6H/8H: Power will turn on immediately and off after hours
you selected.
Button Layout:
Operating Instrutions:
02
ON OFF
2Hr 4Hr
6Hr 8Hr
Timer

4. In the Sensor Mode, temporary light sources like headlights, porch lights
and other external light sources will not interfere with the photocell
function unless the external light source is on for more than 15 minutes.
In that case, the timer will shut off until darkness is restored.
5. When set to "ON", the timer will provide continual power to attached
devices until the timer is switched to OFF", or to any of other operating
modes.
OFF: Power is OFF to attached devices. The "power" indicator will go out.
Control by Receiver:
Press the select button on the receiver, the timer mode will be switched in
the following order: ON-Sensor -Sensor+2H-Sensor+4H-Sensor+6H-Sensor
+8H-Timer+8H-Timer+6H-Timer+4H-Timer+2H-OFF-ON. Cycle repeats.
Control by Transmitter:
1. Press the ON or OFF button to turn the receiver power ON or OFF.
2. Press Timer button plus 2Hr, 4Hr, 6Hr or 8Hr to turn on the receiver, then
off after that specific hour you selected.
The power will be repeated ON daily.
3. Press Sensor button (dusk-to -dawn), the receiver will turn ON when
sensing dusk and Off at dawn.
4. Press Sensor button plus 2Hr, 4Hr, 6Hr or 8Hr to turn on the receiver
when sensing dusk then off after specific hour youselected.
Notes
1. The receiver must be located within 100 feet from the remote transmitter.
Actual function range may be affected by the following factors: weather,
radio frequency interference, low remote battery and obstructions between
the transmitter andreceiver.
2. The timer repeats daily after setting. In case of power failure, the timer
will go back to the off state and need to be reset to the desired operating
mode once power is restored.
3. Once programming activates at sensor with the 2H, 4H, 6H, or 8H Mode,
the program cycle will complete before the timer being reset. Headlights,
porch lights, street lamps and other external lighting sources will not
interfere with the active timerprogram.
03

04
Overload Protection:
The unit has a reset function for overload protection. If the power turns off
unexpectedly, please unplug all devices, press the power switch (resets
device) and reconnect devices.
Battery Handling and Usage
• Install the battery observing the positive (+) side up as indicated
inside the battery compartment.
• Never throw batteries into a fire. Do not expose batteries to fire or
other heat sources.
• Battery contains mercury. Do not put in trash. Recycle or manage
as hazardous waste.
• Remove the battery compartment cover away from the remote (see
diagram below)
• Remove the old battery and place a new Type 3V (CR2032) lithium
battery into the battery compartment.
• Ensure the battery is installed correctly with the
positive (+) side up.
+
CR2032
3V
ON OFF
2Hr 4Hr
6Hr 8Hr
Timer
• Replace the battery compartment cover.
• Dispose or recycle spent/discharged batteries in compliance with
all applicable laws. For detailed information, contact your local
solid waste authority.
Caution: Failure to properly align the battery polarity can cause
personal injury and/or property damage.
1
+
CR2032
3V

Federal Communications Commission Interference Statement
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules . These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
· Reorient or relocate the receiving antenna.
Safety Information
Input Voltage: 125VAC, 60Hz
Max Power Rating: 15A 1875W
Remote Battery; 3V (CR2032) Lithium
Cord: 6ft SJTW 14/3C
Frequency: 433MHz
RECEIVER MODEL: SP-060A
TRANSMITTER MODEL: TR-034-8
FCC ID: PAGTR033-8
Specifications:
05
WARNING:
Do not ingest the battery, Chemical Burn Hazard (The remote control
supplied with) This product contains a coin/button cell battery. If the
coin/button cell battery is swallowed, it can cause severe internal
burns in just 2 hours and can lead to death. Keep new and used
batteries away from children. If the battery compartment does not
close securely, stop using the product and keep it away from children.
If you think batteries might have been swallowed or placed inside any
part of the body, seek immediate medical attention.

(1) this device may not cause interference, and(2) this device must accept
any interference, including interference that may cause undesired
operation of the device.
FCC Caution: Any changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority to operate
this equipment.
CAUTION:
One Year Limited Warranty
Supported by our professional R&D team and QC team, we provide One
Year Warranty for materials and workmanship from the purchase date.
Please note that the warranty does not cover damage caused by personal
misuse or improper installation.
Please attatch your Order ID and Name so that our dedicated customer
service team can help you better.
Risk of Fire. Not for permanent installation. Use only with outdoor
equipment, Christmas-tree, or other seasonal decorative-lighting products
having a total of 15 Ampere maximum. Do not install or use this product
for more than a 90-day period.
If using Christmas tree or decorative - lighting products that are not marked
with an ampere rating, connect no more than 140 screw-base lamps (C7
or C9) or 12 strings with midget (push-in) lamps to this cord set.
Cord sets shall be plugged into a GFCI - protected receptacle. If using an
outdoor-use cord set for an extended period of time (greater than 90 days)
please consider hard wiring a permanent outdoor-use receptacle rated for
year-round use in the area that power is needed. Please contact a Licensed
electrician for proper installation of permanent wiring.
After completion of installation, the connector shall be maintained a
minimum of 6 inches above ground.
06
· Increase the separation between the equipment and the receiver.
· Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
· Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:

07
WARNING: This product can expose you to chemicals including DINP
which is known to the State of California to cause cancer and birth defects
or other reproductive harm.
For more information go to www.P65Warnings.ca.gov.