Digital Monitoring Products 1912XR Owner's manual

123
2841 E. Industrial Drive Springfield, MO 65802-6310 800-641-4282
MODEL 1912XR
COMMAND PROCESSOR PANEL
PROGRAMMING MANUAL
Do Not Throw Away!
This programming manual contains information you need to program and
service the 1912XR panel and should be kept along with your other DMP
technical documentation.
LT-0171 (10/95)

ii
MODEL 1912XR PROGRAMMING MANUAL
Copyright © 1993 – 1995 Digital Monitoring Products, Inc.
Information furnished by DMP is believed to be accurate and reliable.
This information is subject to change without notice.
When using the Series 1912XR control for any UL, NFPA, CSFM, or other listing
organization'sapprovedmethods,refertothismanualand the1912XRInstallationGuide
(LT-0169). These documents outline the installation and programming requirements of
all applications for which the 1912XR is approved.

iii
TABLE OF CONTENTS Section
INTRODUCTION
Before You Begin ............................................................................................ 1.1
Getting Started ................................................................................................ 1.2
Programmer Operation....................................................................................1.3
Programmer Access Codes.............................................................................1.4
Reset Timeout .................................................................................................1.5
Special Keys....................................................................................................1.6
Entering Alpha Characters .............................................................................. 1.7
Entering Spaces with Alpha Characters ..........................................................1.8
Keypad Prompts Display Curent Programming............................................... 1.9
INITIALIZATION
Initialization...................................................................................................... 2.1
Clear All Codes................................................................................................2.2
Clear All Schedules .........................................................................................2.3
Clear Display Events Memory .........................................................................2.4
Clear Loop Information ....................................................................................2.5
Clear Area Information .................................................................................... 2.6
Clear Communication and Remote Options .................................................... 2.7
Set to Factory Defaults ....................................................................................2.8
COMMUNICATION
Communication................................................................................................3.1
Communication Type.......................................................................................3.2
Check-in .................................................................................................... 3.2.1
Existing Wireless....................................................................................... 3.2A
Existing Printer ..........................................................................................3.2B
2nd Phone Line ............................................................................................... 3.3
Test Frequency ......................................................................................... 3.3A
Account Number.............................................................................................. 3.4
Transmit Delay ................................................................................................ 3.5
DTMF...............................................................................................................3.6
Events Manager .............................................................................................. 3.7
Defer Test........................................................................................................ 3.8
Test Frequency................................................................................................3.9
Test Time......................................................................................................... 3.10
Receiver 1 Programming................................................................................. 3.11
Alarm Reports ........................................................................................... 3.12
Supervisory and Trouble Reports ............................................................. 3.13
Opening and Closing Reports by User...................................................... 3.14
Test Report ...............................................................................................3.15
Backup Reporting...................................................................................... 3.16
First Telephone Number ...........................................................................3.17
Second Telephone Number ...................................................................... 3.18
Receiver 2 Programming................................................................................. 3.19
Pager Reporting .............................................................................................. 3.20
DEVICE SETUP
Device Setup ................................................................................................... 4.1
Maximum Partitions ......................................................................................... 4.2
Device Definition.............................................................................................. 4.3
Partition Number.............................................................................................. 4.4
REMOTE OPTIONS
Remote Options............................................................................................... 5.1
Remote Key..................................................................................................... 5.2
Manufacturer Authorization ............................................................................. 5.3
Armed Rings.................................................................................................... 5.4
Disarmed Rings ............................................................................................... 5.5
Alarm Receiver Authorization .......................................................................... 5.6

iv
TABLE OF CONTENTS Section
REMOTE OPTIONS continued
Service Receiver Authorization ....................................................................... 5.7
Remote Phone Number................................................................................... 5.8
Remote Disarm................................................................................................5.9
SYSTEM REPORTS
System Reports ...............................................................................................6.1
Abort Reports .................................................................................................. 6.2
Bypass Reports ...............................................................................................6.3
Schedule Change Reports .............................................................................. 6.4
Code Change Reports..................................................................................... 6.5
Access Keypad Reports ..................................................................................6.6
Ambush Reports.............................................................................................. 6.7
SYSTEM OPTIONS
System Options ...............................................................................................7.1
Close Wait .......................................................................................................7.2
Entry Delay Times ...........................................................................................7.3
Cross Zone Time ............................................................................................. 7.4
Loop Retard Delay...........................................................................................7.5
Power Fail Delay ............................................................................................. 7.6
Swinger Bypass Trips...................................................................................... 7.7
Reset Swinger Bypass .................................................................................... 7.8
Video/Alarm Verification ..................................................................................7.9
OUTPUT OPTIONS
Output Options ................................................................................................ 8.1
Bell Cutoff Time ............................................................................................... 8.2
Automatic Bell Test..........................................................................................8.3
Bell Action........................................................................................................8.4
Fire Type ................................................................................................... 8.4A
Burglary Type............................................................................................ 8.4B
Supervisory Type ...................................................................................... 8.4C
Panic Type ................................................................................................ 8.4D
Emergency Type ....................................................................................... 8.4E
Auxiliary 1 Type........................................................................................ 8.4F
Auxiliary 2 Type........................................................................................ 8.4G
Output Action ................................................................................................... 8.5
Cutoff Output............................................................................................. 8.5A
Output Cutoff Time....................................................................................8.5B
Communication Failure Output .................................................................8.5C
Fire Alarm Output......................................................................................8.5D
Fire Trouble Output ................................................................................... 8.5E
Ambush Output ......................................................................................... 8.5F
Entry Output .............................................................................................. 8.5G
Exit Output ................................................................................................8.5H
Ready Output ............................................................................................ 8.5I
Phone Trouble Output...............................................................................8.5J
Late To Close Output ................................................................................ 8.5K
Device Fail Output..................................................................................... 8.5L
MENU DISPLAY
Menu Display ................................................................................................... 9.1
Armed Status ................................................................................................... 9.2
Time................................................................................................................. 9.3
Arm/Disarm......................................................................................................9.4

v
TABLE OF CONTENTS Section
STATUS LIST
Status List...................................................................................................... 10.1
Display Keypads ............................................................................................ 10.2
System Monitor Troubles............................................................................... 10.3
Fire Loops......................................................................................................10.4
Burglary Loops .............................................................................................. 10.5
Supervisory Loops......................................................................................... 10.6
Panic Loops ................................................................................................... 10.7
Emergency Loops.......................................................................................... 10.8
Auxiliary 1 Loops ...........................................................................................10.9
Auxiliary 2 Loops ...........................................................................................10.10
PRINTER REPORTS
Printer Reports .............................................................................................. 11.1
Arm and Disarm Reports ............................................................................... 11.2
Loop Reports ................................................................................................. 11.3
User Command Reports................................................................................ 11.4
Door Access Reports..................................................................................... 11.5
Supervisory Reports ...................................................................................... 11.6
AREA INFORMATION
Area Information ............................................................................................ 12.1
Partition Number............................................................................................ 12.2
Mode.............................................................................................................. 12.3
Exit Delay ...................................................................................................... 12.4
Burglary Output ............................................................................................. 12.5
Opening and Closing Reports ....................................................................... 12.6
Closing Check ............................................................................................... 12.7
Closing Code ................................................................................................. 12.8
Any Bypass....................................................................................................12.9
Area Schedules ............................................................................................. 12.10
Primary/Secondary Schedules ......................................................................12.11
Area Number ................................................................................................. 12.12
Area Name .................................................................................................... 12.13
Account Number ............................................................................................ 12.14
Automatic Arming .......................................................................................... 12.15
Bad Loops ..................................................................................................... 12.16
Automatic Disarming ..................................................................................... 12.17
Armed Output Number .................................................................................. 12.18
Bank Safe and Vault...................................................................................... 12.19
Common Area ............................................................................................... 12.20
LOOP INFORMATION
Loop Information............................................................................................ 13.1
Loop Number ................................................................................................. 13.2
Loop Name .................................................................................................... 13.3
Loop Type......................................................................................................13.4
Loop Type Specifications ........................................................................ 13.4A
Partition Number............................................................................................ 13.5
Area Number........................................................................................... 13.5A
Area Perimeter ........................................................................................13.5B
Arming Loop Area Assignment ...............................................................13.5C
Next Loop ......................................................................................................13.6
Alarm Action .................................................................................................. 13.7
Disarmed Open ............................................................................................. 13.8
Report To Transmit ................................................................................. 13.8A

vi
TABLE OF CONTENTS
Section
LOOP INFORMATION continued
Output Number........................................................................................13.8B
Output Action .......................................................................................... 13.8C
Swinger Bypass............................................................................................. 13.9
Fast Response ..............................................................................................13.10
Restoral .........................................................................................................13.11
Cross Zone .................................................................................................... 13.12
Priority ...........................................................................................................13.13
Setup Loop Expanders ..................................................................................13.14
Program Transmitter ...............................................................................13.14A
Connect Transmitter................................................................................13.14B
Connect Command Transmitter .............................................................. 13.14C
Existing DNET......................................................................................... 13.14D
Existing Printer ........................................................................................13.14E
Prewarn Addresses .......................................................................................13.15
Entry Delay .................................................................................................... 13.16
Loop Retard...................................................................................................13.17
Presignal Addresses......................................................................................13.18
STOP
Stop ...............................................................................................................14.1
SET ACCESS CODE
Set Access Code ...........................................................................................15.1
APPENDIX
Events Manager ............................................................................................16.1
Loop Type Descriptions................................................................................. 16.2
Diagnostics Function .....................................................................................16.3
New and recent additions
Sec. Description Date
1.5 Revised the Reset Timeout description. 6/95
3.2 Added the Contact ID format option. 6/95
3.2A Added Existing Wireless display description. 6/95
3.2B Added Existing Printer display description. 6/95
3.3 Added Cellular prompt for 2nd phone line. 6/95
3.18 Added description of alternate dial sequence. 6/95
4.3 Added new single loop modules. 6/95
6.2 Abort report during Transmit Delay description. 6/95
7.9 Added Video/Alarm Verification description. 6/95
8.5 Revised the Output Action description. 6/95
11.1 Added Printer Reports sections (11.1 to 11.6). 6/95
12.3 Revised Home/Away description. 6/95
12.18 Revised Armed Output Number description. 6/95
13.6A Added Wireless programming instructions. 6/95
13.8A Added programming caution note. 6/95
14.1 Revised the Stop Routine function description. 6/95
16.3 Revised the Test 881 function description. 6/95
Sec. Description Date
3.2 Added the Host Communication Type. 7/95
3.2.1 Added Check-in Time for Host Communication. 7/95
3.3 Added Host option for 2nd phone line. 7/95
3.20 Added Pager Direct™ reporting option. 7/95
3.3 Added "area code" for cellular reporting 10/95

Digital Monitoring Products, Inc. 1912XR Programming
Page 1
1-INTRODUCTION
Introduction
1.1 Before You Begin
About this Manual
This manual provides programming information for the DMP 1912XR Command Processor panel.
After this Introduction, the remaining sections describe the functions of each programming menu
item along with the available options. The 1912XR contains all of its programming information in an
on board processor and does not require an external programmer. After resetting the panel from
jumper J16, you can perform all programming tasks through any DMP alphanumeric keypad
connected to the system.
Reading the Contents
Before starting to program, we recommend you read through the contents of this manual. The
information contained here allows you to quickly learn the programming options and operational
capabilities of the 1912XR panel.
In addition to this manual, you should also read and be familiar with the following 1912XR
documents:
• 1912XR Installation Guide (LT-0169)
• 1912XR Product Specification (LT-0170)
• 1912XR Security Command® User's Guide (LT-0172)
Programming Information Sheet
Included with each 1912XR panel are the Programming Information Sheets. These list the various
keypad prompts and available options for programming the panel. Before starting, we recommend
you completely fill out each sheet with the programming options you intend to enter into the panel.
Having completed programming sheets available while entering data helps to prevent errors and can
shorten the length of time you spend programming. Completed sheets also provide you with an
accurate account of the panel's program you can keep on file for future system service or expansion.
The remainder of this Introduction provides instructions for starting and ending a 1912XR
programming session using the alphanumeric keypad.
1.2 Getting Started
The 1912XR Command Processor panel and all loop expansion devices must be completely
installed before you begin programming. Make sure the panel is properly grounded. Connect AC
power and a battery to the appropriate panel terminals.
Initializing the Panel
When programming a 1912XR panel for the first time, or changing the program of an existing
1912XR, we reccomend you use the Initialization function. See section 2. Initializing the panel
clears previously programmed information from the panel's memory.
Program from any Keypad Address
All 1912XR programming is done through keypads correctly addressed and connected to the
system. See the 1912XR Installation Guide (LT-0169) for keypad addressing and installation
information. If you're programming a panel that does not have a keypad, you can temporarily use an
alphanumeric keypad set to address zero (all switches down). While programming with a keypad set
to address zero, you cannot program from any other address.
Select address zero by placing all switches on the switchblock inside the keypad to the down
position.

Digital Monitoring Products, Inc. 1912XR Programming
Page 2
1-INTRODUCTION
1.2 Getting Started continued
Accessing the Programmer
To access the Programmer function of the 1912XR:
1. Install the reset jumper across the two J16 reset pins for two seconds. See Figure 1.
2. Remove the reset jumper and place it over just one pin for future use.
3. Enter the code 6653 (PROG) into any Security Command keypad.
4. Press COMMAND.
5. The keypad displays: PROGRAMMER.
You are now ready to start programming the 1912XR panel. Pressing the COMMAND key scrolls
you through the programming functions listed in section 1.3. Each of these functions are described
in detail in sections 2 to 15 of this manual.
1.3 Programmer Operation
Once at the PROGRAMMER display, pressing the COMMAND key scrolls you through the
programming menu. There are 14 programming sections to choose from:
Menu Item Section in this manual
Initialization 2
Communication 3
Device Setup 4
Remote Options 5
System Reports 6
System Options 7
Output Options 8
Menu Display 9
Status List 10
Printer Reports 11
Area Information 12
Loop Information 13
Stop 14
Set Access Code 15
AC BELL
AC
1234 567 89
10 11 12 13 14 15 16 17 18 19
GND RED YEL GRN BLKB + B - SMK L5+ L5- L1 L2 L3 L4GNDGND
1k Ω
3.3k ΩResistor
DMP Model 309
1k Ω1k Ω
Battery Only Restart
J16
Command Processor Reset
1k Ω
Cold Water Pipe
Earth Ground
Figure 1: Installing the reset jumper on J16
J16

Digital Monitoring Products, Inc. 1912XR Programming
Page 3
1-INTRODUCTION
1.3 Programmer Operation continued
To select a section for programming, press any one of the top row SELECT keys when the name of
that section is displayed on the keypad. The detailed instructions for each programming step are
found in sections 2 to 15 of this manual.
1.4 Programmer Access Codes
The 1912XR panel allows you to enter the programming function without a code using the steps 1 to
5 listed in section 1.2. We recommend, however, that you install an Access Code that restricts
programming to only those persons your company authorizes. You can do this by using the SET
ACCESS CODE feature in the programmer.
Use this new Access Code to restrict any unauthorized programming of the panel.
Installing an Access Code
After entering the programming function, the keypad displays PROGRAMMER. Press the
COMMAND key to advance through the programming sections until SET ACCESS CODE is
displayed (after STOP). Press any top row SELECT key and then enter a 1 to 5 digit programmer
access code.
Note: There are certain codes used by the panel that cannot be used for an Access Code. When
programming an Access Code, do not:
• Enter a number larger than 65,535
• Use 6653 (PROG), 2313 (DIAG), or any 3-digit code starting with 98 (such as 984).
These codes must be left available for the panel's use.
Press COMMAND. The displays shows ENTER AGAIN. Enter the new access code again and
press COMMAND. The display shows CODE CHANGED. The new code number must now be
entered before the programmer function can be accessed.
This code number should be kept in a secure place with access limited to only those persons
authorized by your company to program the panel.
Lost Access Code requires factory reset: If you lose or forget the Access Code, the panel must
be sent back to the factory to be reset. There is no field option for gaining access to the panel
without a valid access code.
1.5 Reset Timeout
The 1912XR has a feature that requires you to enter the Programmer within 30 minutes of resetting
the panel. After 30 minutes, if you attempt to program by entering the 6653 (PROG) code, the
keypad displays: RESET PANEL. You must reset the panel and enter the program code within the
next 30 minutes.
If you are already in the Programmer and do not press any keys on the programming keypad for 30
minutes, the panel terminates programming. As an additional safeguard, all data entered up to that
time is saved in the panel's memory.

Digital Monitoring Products, Inc. 1912XR Programming
Page 4
1-INTRODUCTION
1.6 Special Keys
COMMAND Key
The COMMAND key is used to step ahead in programming. Pressing the COMMAND key allows
you to go forward through the programming menu and through each step of a programming section.
As you go through the programming, the keypad display shows any current programming already
stored in the panel's memory.
If the information is not to be changed, press the COMMAND key to advance to the next step.
The COMMAND key is also used to enter information into the panel's memory such as phone
numbers or loop names. Press the COMMAND key after you've entered the information and it's
being displayed correctly on the keypad.
ARROW Key
Use the ARROW key to back up one step while in the programming menu or within a programming
section. The ARROW key is also used when an error is made while entering information. Press the
ARROW key once to erase the last character entered.
SELECT Keys
The top row of keys are called the SELECT keys. Each time a SELECT key is to be used, the
keypad displays the function or options above the key. Displaying choices above the individual
SELECT keys allows them to be used for many different applications. For example, you can enter
AM or PM when programming the automatic test time or answer YES or NO for a system option.
During programming, the SELECT keys also allow you to change information currently in the panel's
memory. As you step through each program option, the keypad displays the current information. To
change this information, press the appropriate SELECT key under the display then enter the new
information through the keypad.
If you are changing a phone number or account number, press the appropriate digit keys. If entering
a communication type or choosing a programming option, the keypad displays the available
response options above the SELECT keys. When there are more than four response options
available, the keypad displays the first four. Pressing the COMMAND key brings up the next 1 to 4
options on the display. Pressing the ARROW key allows you to review the previous four choices.
The SELECT keys are also used for selecting a section from the programming menu. This is done
by pressing any one of the SELECT keys when the name of the programming section you want is
displayed.
1234
5678
90
COMMAND
A B C DEF GHI JKL
VWX
STUPQRMNO
YZ
POWER
Figure 2: Keypad Function keys
COMMAND Key
ARROW Key
SELECT Keys

Digital Monitoring Products, Inc. 1912XR Programming
Page 5
1-INTRODUCTION
Figure 3: Keypad display and top row keys
Center Character
Left Character Right Character
S Y S T E M O N
BELL TST YES
Press the top row select key.
BELL TST NO
The keypad display changes to the newly
selected option. Press COMMAND.
NEXT
Figure 4: Changing the current option selected.
1.7 Entering Alpha Characters
Some options during programming require you to enter alpha characters. To enter an alpha
character, press the key that has that letter written below it. The keypad displays the number digit of
the key. Next, press the SELECT key that corresponds to the location of the letter under the key.
Pressing a different SELECT key changes the letter. When another digit key is pressed, the last
letter displayed is retained and the process is started over.
1.8 Entering Spaces With Alpha Characters
To enter a space in an alpha entry, press the 9 digit key followed by the third SELECT key. The
three characters on the 9 digit key are Y, Z, and space.
1.9 Keypad Prompts Display Current Programming
Each programming prompt displayed at the keypad shows the currently selected option in the
panel's memory. These options are either shown as a number, a blank, or a NO or YES. To change
a number or blank to a new number, press any top row SELECT key. The current option is replaced
with a dash. Press the number(s) on the keypad you want to enter as the new number for that
prompt.
It is not necessary to enter numbers with leading or trailing zeros. The 1912XR automatically right
justifies the number when you press the COMMAND key.
To change a programming prompt that requires a NO or YES response, press the top row SELECT
key under the response not selected.
For example, if the current prompt is selected as YES and you want to change it to NO, press the
third top row SELECT key. The display changes to NO. Press the COMMAND key to go to the next
prompt. See Figure 4.

Digital Monitoring Products, Inc. 1912XR Programming
Page 6
2-INITIALIZATION
2.1 This function allows you to clear selected parts of the panel's memory back to the
factory defaults in preparation for system programming.
After you select YES to clear a section of memory the panel asks if you are sure
you want to clear the memory. This is a safeguard against accidently erasing part
of your programming. No memory is cleared from the programming until you
answer yes to the SURE? YES NO question.
A description of each selection follows:
2.2 CLEAR ALL CODES - YES clears the user code memory and assigns the
user code number 99 to the highest user position in each area.
2.3 CLEAR ALL SCHEDULES - YES clears all primary, secondary, permanent,
temporary, and output schedules.
2.4 CLEAR DISPLAY EVENTS MEMORY - YES clears the Security Command
keypad display events memory.
2.5 CLEAR LOOP INFORMATION - YES clears the loop information for all loops. All
loops are marked * UNUSED * and must be renamed before being able to
display on any system keypad.
2.6 CLEAR AREA INFORMATION - YES clears the area information for all areas. All
areas are marked * UNUSED * and must be renamed before being able to
display on any system keypad.
2.7 CLEAR COMMUNICATION AND REMOTE OPTIONS - YES clears the
communication and remote options programming to factory defaults.
2.8 SET TO FACTORY DEFAULTS - YES sets the panel's programming back to the
factory default selections. Selecting Factory Defaults does not clear the panel's
Event Memory or user codes.
INITIALIZATION
CODES? NO YES
SURE? YES NO
SCHEDS? NO YES
SURE? YES NO
EVENTS? NO YES
SURE? YES NO
LOOPS? NO YES
SURE? YES NO
AREAS? NO YES
SURE? YES NO
COM/RMT? NO YES
SURE? YES NO
DEFAULTS NO YES
SURE? YES NO

Digital Monitoring Products, Inc. 1912XR Programming
Page 7
3.1 This section allows you to configure the communication options for the 1912XR
panel. The information you'll program varies with the Communication Type.
3.2 COMMUNICATION TYPE - Specifies the communication method the panel uses
to contact the SCS-1 Receiver. Press any SELECT key to display the following
communication options:
NONE - For local systems. Selecting this ends communication programming.
DD - Dialer connection to a DMP SCS-1 Receiver.
MPX - Multiplex connection to a DMP SCS-1 Receiver.
DDMX - Dialer connection during disarmed periods with multiplex connection
established after the last area in the system arms. After selecting DDMX, the
display changes to DDMX PHONE NO., press COMMAND to enter the multiplex
phone number.
DNET - Data network connection to a DMP SCS-1 Receiver following multiplex
rules. This option requires the use of the 862 Network Interface Card. You can
also use the backup dialer capability of the 1912XR by selecting the option 2ND
LINE as YES. See section 3.3.
You cannot select DNET if you are using the 872 H ARD - WIRE - LESS ™ or 862P Printer
Interface Cards: If you attempt to program DNET while using either card, the keypad
displays an error message. See sections 3.2A and 3.2B.
CID - This option allows the panel to communicate to non-DMP receivers using
the Ademco Contact ID format. When selected, the panel sends all of its alarm,
trouble, and supervisory reports to the Contact ID receiver programmed in
Receiver 1 and 2 Programming.
HST (Host) - Asynchronous communication using the 862N Network Interface
Card. The DMP Host/Output reporting format is transmitted over an
asynchronous computer or radio network to the SCS-1 Receiver. All loop alarms
and restorals transmitted on the Host Channel are also duplicated on the 2ND
LINE (section 3.3) if it's selected.
If the Host channel fails to receive a proper acknowledgment after five attempts,
the panel sends a WARNING: NETWORK TROUBLE (S72) report on the 2ND
LINE. The next time a report is sent by the panel over the Host channel, the
panel sends a NETWORK RESTORED (S73) report over the 2ND LINE.
3.2.1 CHECK-IN TIME - Enter two digits (00 to 60) to specify the time delay in minutes
the panel uses to send the next Check-in report. This prompt is only displayed if
HST is selected in section 3.2. Since HST is not a polled communication method,
the Check-in time allows the SCS-1 Receiver to get a Check-in report (s070)
periodically to verify continuous communication with the panel. SCS-1/805
firmware is required in the SCS-1 Receiver. Entering zero causes the Check-in
report to not be sent. Press COMMAND to continue.
Selecting AA instead of entering a Check-in time causes the panel to send the
Check-in report at random times. When all areas are disarmed, the report is sent
randomly but always within 60 minutes. If any area is armed, the report is sent
every six minutes. The SCS-1 Receiver verifies that the next Check-in report is
received at the appropriate time. SCS-1/805 firmware is required in the SCS-1
Receiver.
3.2A EXISTING WIRELESS - Wireless loops have been programmed for one or more
of the addresses 100 to 199. This display is followed by the loop number and
loop name for each wireless loop. You must remove the wireless loop
programming to use the DNET option for interfacing with a data network.
COMM TYPE: NONE
3-COMMUNICATION
COMMUNICATION
NONE DD MPX DDMX
DNET C I D HST
EXISTING WIRLESS
CHECKIN:
CHECKIN: – AA

Digital Monitoring Products, Inc. 1912XR Programming
Page 8
3.2B EXISTING PRINTER - One or more options in Printer Reports has been enabled.
See section 11.1. You must remove any Printer Reports programming before
using the DNET option to interface with a data network.
3.3 2ND PHONE LINE - Allows you to use a second phone line to send reports to the
SCS-1 Receiver should the first phone line fail. If 2ND LINE is YES, you'll need
to install a DMP 893 Dual Line Module to connect both the main and secondary
phone lines. The 893 provides supervision of both phone lines.
Both DD and MPX type systems can be backed up with a dialer or cellular line.
Multiplex lines cannot be used as a secondary line.
NONE - A second line is not used.
DD - Dialer communication to a DMP SCS-1 Receiver.
CELL - Cellular communication with Cell-Miser™ restrictions. When Cell-Miser is
selected, the following call restrictions apply to the panel.
1. Only loop alarms, Ambush, Line 1 Trouble, Abort, Recall Test, and Delayed
Events can be sent over the cellular system. Delayed Events are only sent
if the cellular call was made for one of the other allowed reports.
2. Line 1 Trouble in sent only once during each armed period.
Area code selection for cellular communication: Version 1912XR/112 firmware allows you to
enter a letter "C" in the first or second phone number in the panel's Communication section of the
Programmer. When entered, the characters before the "C" are only used when a 2nd LINE Cellular
call is being made. All other calls made on the main line will only use the characters entered after
the letter "C". The letter "C" is never dialed and is recognized by the panel as a marker only.
HST (HOST) - DTE asynchronous communication to a DMP SCS-1 Receiver or
Host automation system. If HST is selected as the Communication Type in
section 3.2, HST will not be displayed as an option in 2ND LINE. If HST is
selected for 2ND LINE, all loop alarms and restorals are duplicated on the
asynchronous channel in addition to the main communication method.
When HST is used as the main or 2ND LINE communication method, the
account number must not begin with a number that matches a line number being
used for multiplex service on the same SCS-1 Receiver. This allows the
Redisplay Non-Restored status list to work properly in receivers with SCS1/805
firmware.
3.3A TEST FREQUENCY - Specifies the communication test interval for the second
phone line. This is displayed if 2ND LINE is programmed as DD or CELL.
NONE - No communication test is made on the second line.
REG - A 2ND LINE communication test is made each time the regular
communication test is completed.
7 - A communication test is made every 7 days at the test time programmed for
the regular communication test. Test time deferrals are disregarded.
30 - A communication test is made every 30 days at the test time programmed
for the regular communication test. Test time deferrals are disregarded.
If the 2ND LINE test fails to communicate after 10 attempts, the regular communication channel
sends a WARNING: PANEL BACKUP COMMUNICATION FAIL (S12) report. The next time the
panel sends a report over the 2ND LINE, the regular communication channel sends a BACKUP
COMMUNICATION LINE RESTORED (S04) report.
3-COMMUNICATION
NONE DD CELL HST
2ND LINE: NONE
NONE REG 7 30
TEST FREQ: NONE
EXISTING PRINTER

Digital Monitoring Products, Inc. 1912XR Programming
Page 9
3.4 ACCOUNT NUMBER - Enter the account number sent to the SCS-1 Receiver.
DD, CID, and HST - The range of valid account numbers for a panel using
these Communication Types is 1 to 65,535. For account numbers of four
digits or less, it is not necessary to enter leading zeros. The panel
automatically right justifies the account number.
MPX, DDMX, and DNET - A 5-digit account number is required for panels
using either of these formats. The first digit is the receiver line number. The
second digit is always zero. The last three digits are the panel's account
number. This number must be between the range of 000 and 127.
If 2ND LINE (3.3) is NO, COMMUNICATION programming ends after the
account number is entered.
3.5 TRANSMIT DELAY- Enter the length of time the panel waits before sending
burglary reports to the SCS-1 Receiver. The available range is 1 to 60 seconds.
Alarm bells and relay outputs are not delayed during this period. Burglary
Outputs in section 8 must be programmed for pulsed or steady. Set Abort
Reports in section 6 to YES if Opening and Closing reports are not being sent.
Enter zero to disable Transmit Delay.
3.6 DTMF - YES enables tone dialing. NO enables rotary dialing.
3.7 EVENTS MANAGER - Specifies when non-alarm reports are sent to the receiver.
This selection does not affect loop alarm, loop trouble, loop restoral, supervisory,
or serviceman messages. Closing reports are not delayed if you've programmed
a YES for the Closing Wait option. See Section 7.2.
SND - If send is selected, all reports are sent to the receiver as they occur.
DLY - All non-alarm reports are held until the panel's memory buffer contains
66 events, or until the panel's next communication with the receiver.
KEEP - All non-alarm reports are held in the panel's memory buffer until
they're over written by new activity. You can view the contents of the memory
buffer using the DMP Remote Access™ software or the display events
feature in the User Menu.
Refer to the Appendix for a table listing the delayed report types.
3.8 DEFER TEST TIME - Select YES to allow the programmed test report to be
deferred if the panel communicates with the SCS-1 Receiver within the time set
in Test Frequency. See section 3.9. Select NO to send the test report as
programmed regardless of previous panel communication.
3.9 TEST FREQUENCY - Allows you to set how often the panel's test report is sent
to the SCS-1 receiver. Enter from 1 to 60 days. This prompt is not displayed if
Defer Test Time is set to NO.
3.10 Press COMMAND to show the enter test time display.
Enter the time of day the panel sends the test report to the SCS-1 Receiver. Use
only entries of 00:01 to 12:00 and then choose AM or PM.
When Defer Test Time is set to NO, this option allows you to program the day of
the week the test report is sent. Choose one day of the week or all days.
3.11 Allows you to set the options for the first receiver the 1912XR panel attempts to
contact when sending reports. The panel supports two receivers.
3.12 ALARM REPORTS - YES sends alarm and alarm restoral reports to this receiver.
3-COMMUNICATION
EVENT MGR: SEND
DTMF YES
SND DLY KEEP
DFR TEST NO
TEST FREQ: 0
TEST TIME
0 : 0 0 A M PM
RECEIVER 1 PRGMG
TEST DAY: ALL
ACCT NO: 1 2 3 4 5
XMIT DELAY: 0
ALARM YES

Digital Monitoring Products, Inc. 1912XR Programming
Page 10
3.13 SUPERVISORY/TROUBLE REPORTS - YES enables supervisory, trouble, and
trouble restoral reports, and serviceman messages to be sent to this receiver.
3.14 OPENING/CLOSING AND USER REPORTS - Enter YES to enable opening/
closing, door access, schedule and code changes, bypass, and sensor reset
reports by user to be sent to this receiver.
3.15 TEST REPORT - Enter YES to enable the system test report to be sent to this
receiver. Reports are sent according to the programming in sections 3.9 to 3.10.
3.16 BACKUP REPORTING - Enter YES to enable this receiver to be a backup to the
other receiver in the event the other receiver cannot be contacted.
3.17 FIRST TELEPHONE NUMBER - This is the first number the panel dials when
sending reports to this receiver. Phone numbers can be up to 15 characters in
length. You can program a three second pause in the dialing sequence by
entering the letter P. You can program a dial tone detect by entering the letter D.
These characters are counted as part of the 15 allowable characters.
3.18 SECOND TELEPHONE NUMBER - The panel dials the second number when
two successive tries using the first number have failed. If the panel cannot reach
the receiver after two attempts using the second number, it returns to the first
number and makes two additional attempts. A total of ten dialing attempts are
made using the first and second phone numbers.
Should all ten attempts fail, the panel clears the communication buffer and then
makes one communication attempt each hour to send a TRANSMIT FAILED
(S87) report to the central station receiver. The report information that was not
sent to the receiver is available from the Display Events feature of the User Menu
and can be downloaded with the Remote Access™ software from DMP.
Each number can be up to 15 characters in length including any P or D
characters entered for pause and dial tone detect. Important: Do not program
any letters other than P or D.
3.19 Repeat steps 3.12 through 3.18 when using a second receiver. Defaults for
Receiver 2 are factory set as NO.
If you select YES for any of the second receiver options, you must have at least
one phone number programmed in Receiver 2 programming.
3.20 PAGER REPORTING - YES allows the panel to send Alarm, Trouble, Opening,
Closing, and Late to Close reports to a numeric pager. The panel uses DTMF
tones to generate the account and report information sent over the pager terminal
equipment. Selecting NO allows you to use the Receiver 2 Programming to send
panel reports to a second SCS-1 Receiver.
3.20A FIRST TELEPHONE NUMBER - Enter the phone number the panel will dial to
send reports to the numeric pager. Phone numbers can be 15 characters in
length. You can program a three second pause in the dialing sequence by
entering the letter P. You can program a dial tone detect by entering the letter D.
These characters are counted as part of the 15 allowable characters.
3.20B PAGER IDENTIFICATION NUMBER - Enter a pager identification number if your
pager uses one. If it does, the panel waits for nine seconds after having dialed the
First Phone Number before sending the Pager ID. After the Pager ID has been
transmitted, the panel waits another three seconds before sending the actual
pager message containing the panel reports.
3-COMMUNICATION
SPV/TRBL YES
SECOND PHONE NO.
–
O/C USER YES
BACKUP NO
FIRST PHONE NO.
–
TEST RPT YES
RECEIVER 2 PRGMG
FIRST PHONE NO.
PAGER ID NUMBER
PAGER? NO YES

Digital Monitoring Products, Inc. 1912XR Programming
Page 11
4.1 This section allows you to define the physical configuration of the 1912XR panel.
Enter the number of partitions in the system and the types of devices installed at
each address along with their assigned partition. You can install and address up
to eight devices on the keypad data bus.
A description of each option follows:
4.2 Maximum number of partitions you want in this system. You can choose from 1 to
4. To change the number displayed, press any SELECT key, enter the number of
partitions you want to enable, and press COMMAND.
Changing the number of partitions resets user codes: Whenever you change the number of
partitions on the 1912XR, all programmed user codes are cleared. The only code available after a
partition change is the factory default of 99.
4.3 Description of the device set to this address. Leave the default STNDRD for 670,
770, and 771 Security Command keypads and for all expander modules.
If the device description does not match the device installed for this address,
press any SELECT key and choose the correct one from those displayed.
STANDARD - The device is either a 670, 770, or 771 keypad, a 711, 714, or 715
Loop Expander, a 6155LX PIR, or a 5845LX Glassbreak.
NONE - No device is set for this address.
Press the SELECT key under the correct device description to change the current
selection. If you entered 2, 3, or 4 in section 4.2 MAX PARTITION, the keypad
displays the following prompt. If there is only one partition programmed in section
4.2, the keypad does not display the partition assignment prompt.
4.4 Enter the partition number where the current device being programmed is
assigned. For systems with only one partition, leave this entry at one. For
systems with more than one partition, press any top row SELECT key then enter
a 2, 3, or 4. Press COMMAND to program the next device.
Figure 5: Areas and user codes available with partitioning
Partitions
Enabled Areas Available User Code Numbers
Partition 1 1 to 8 1 to 99
Partitions 1 & 2 Partition 1 - 1 to 8
Partition 2 - 1 to 4
Partition 1 - up to 50
Partition 2 - up to 50
Partitions 1 to 3 Partition 1 - 1 to 8
Partition 2 - 1 to 4
Partition 3 - 1 to 4
Partition 1 - up to 25
Partition 2 - up to 25
Partition 3 - up to 25
Partitions 1 to 4 Partition 1 - 1 to 8
Partition 2 - 1 to 4
Partition 3 - 1 to 4
Partition 4 - 1 to 4
Partition 1 - up to 25
Partition 2 - up to 25
Partition 3 - up to 25
Partition 4 - up to 25
MAX PARTITION: 1
DEVICE 1: STNDRD
STD NONE
PARTITION NO: 1
DEVICE SETUP
4-DEVICE SETUP

Digital Monitoring Products, Inc. 1912XR Programming
Page 12
5.1 This section allows you to enter the information needed for Remote Command/
Remote Programming operation.
A description of the Remote Options follow:
5.2 REMOTE KEY - This option allows you to enter a code of up to eight digits for
use in verifying the authority of an alarm or service receiver to perform a remote
command/programming session. The receiver must give the correct key to the
panel before being allowed any remote functions. All panels are shipped from the
factory with the key preset as blank.
To enter a remote key or change the current one, press a top row SELECT key
and enter any combination of up to eight digits. Press COMMAND. The current
key is never displayed.
5.3 MANUFACTURER AUTHORIZATION - Enter YES to allow DMP service
technicians to access the panel when required during system service or
troubleshooting. This authorization automatically expires within one hour.
DMP remote service is provided on a read only basis: DMP technicians can look at the system
programming and make suggestions only. Alterations can only be accomplished by the installing
company's service personnel.
5.4 ARMED RINGS - Enter the number of rings the panel counts before answering
the phone line when all areas of the system are armed. Any number from 1 to 15
can be entered. If zero is entered, the panel does not answer the phone when all
areas of the system are armed.
5.5 DISARMED RINGS - Enter the number of rings the panel counts before
answering the phone line while any areas of the system are disarmed. Any
number from 1 to 15 can be entered. If zero is entered, the panel does not
answer the phone when any area of the system is disarmed.
5.6 ALARM RECEIVER AUTHORIZATION - Enter YES to enable remote
commands and programming to be accepted from the alarm SCS-1 Receiver.
The Remote Key option can also be required.
With YES selected, the panel requests the receiver key during its first
communication with the first SCS-1 receiver. The panel retains this alarm
receiver key in memory and allows remote commands to be accepted from the
alarm receiver. If an alarm occurs during a remote connect, the alarm report is
immediately sent to this receiver only.
When NO is selected, remote commands and programming are not accepted
from the alarm SCS-1 Receiver.
ALR RCVR NO
RMT KEY:
DISARM RINGS: 0
MFG AUTH NO
5-REMOTE OPTIONS
ARM RINGS: 0
REMOTE OPTIONS

Digital Monitoring Products, Inc. 1912XR Programming
Page 13
5.7 SERVICE RECEIVER AUTHORIZATION - YES enables remote commands and
programming to be accepted from a secondary service receiver other than the
alarm SCS-1 Receiver. The Remote Key option can also be required.
With YES selected, the panel requests the service receiver key the first time it's
contacted by the service receiver. The panel retains this service receiver key in
memory and accepts remote commands from the service receiver.
If an alarm occurs during a remote connect, the panel disconnects from the
service receiver and calls the alarm receiver. Alarm reports are only sent to the
alarm receiver. It is important that the alarm receiver key and the service
receiver key programmed at the central station are NOT the same so the panel
can determine the difference between receivers.
When NO is selected remote commands and programming are not accepted
from a secondary service receiver.
5.8 REMOTE PHONE NUMBER - Press COMMAND to enter the phone number the
panel dials whenever remote programming is requested. After entering a phone
number, the panel allows remote commands and programming only after it has
first been called by the authorized receiver, disconnected itself, and has redialed
the remote phone number.
Note: If a Remote Phone Number is entered, and the function 984 + COMMAND
is entered at the keypad, a remote options menu appears. This menu contains
the following options:
NUMBER - The panel allows you to enter into the keypad a phone number you
want the panel to dial. Use must use any required prefixes and area codes.
REMOTE - The panel dials the phone number programmed in Remote Phone
Number. See section 5.8.
PICKUP - The panel picks up the phone line as Remote Access is dialing in. The
phone must be ringing before selecting PICKUP.
If a Remote Phone Number is NOT entered, the panel allows remote commands
and programming without disconnecting and redialing. The phone number can be
up to 15 digits in length. Enter a D for dial tone detect and a P for a 3 second
pause.
Important: Do not program any letters other than P or D.
5.9 REMOTE DISARM - Enter YES to enable the panel to be disarmed remotely.
Selecting NO disables remote disarming.
REMOTE PHONE NO.
SVC RCVR YES
–
DISARM NO
NBR RMT PICKUP
5-REMOTE OPTIONS

Digital Monitoring Products, Inc. 1912XR Programming
Page 14
6.1 This function allows you to select the reports the 1912XR sends to the SCS-1
Receiver.
6.2 ABORT REPORT - YES allows the panel to send an alarm abort report to the
receiver any time an alarm report has also been sent and the bell is still
sounding. The area must be disarmed and no alarmed loops can still be armed.
Abort reports are also sent when the system is disarmed during Transmit Delay
and the Bell Output is active. See section 3.5.
6.3 BYPASS REPORTS - YES allows the panel to send all loop bypasses, resets,
and force arm reports to the receiver. The bypass report includes the loop
number, loop name, and the user number of the individual operating the system.
6.4 SCHEDULE CHANGE REPORTS - YES allows the panel to send all permanent
and temporary, primary and secondary, schedule changes to the receiver. The
report includes the day, opening time, closing time, and the user number of the
individual making the change.
6.5 CODE CHANGE REPORTS - YES allows the panel to send all code additions,
changes, and deletions to the receiver. The code change report includes the user
number added or deleted and the user number of the individual making the
change.
6.6 ACCESS KEYPADS - Enter the Security Command keypad addresses that send
door access reports to the receiver. A report is sent with each door access made
from the selected keypads. Keypads at addresses not selected still operate the
door strike relay but do not send door access reports. The report includes the
user number and the keypad address used.
6.7 AMBUSH - YES allows an ambush report to be sent anytime user code number
one is entered at a Security Command keypad. Selecting NO disables the
ambush report and allows user code number one to operate the same as all
other codes.
There is one Ambush code available for each active partition programmed into
the panel.
ABORT NO
SYSTEM REPORTS
CODE CHG YES
BYPASS YES
SCHD CHG YES
AMBUSH NO
ACS KEY: - - - - - - - -
6 -SYSTEM REPORTS