Digital Monitoring Products XT Series User manual

INSTALLATION GUIDE
DIGITAL MONITORING PRODUCTS, INC.

MODEL XT30/XT50 SERIES
CONTROL PANEL INSTALLATION GUIDE
© 2021 Digital Monitoring Products, Inc.
Information furnished by DMP is believed to be accurate and reliable.
This information is subject to change without notice

Terminal 8 - YEL.......................................................................................9
Terminal 9 - GRN.....................................................................................9
Terminal 10 - BLK ....................................................................................9
Keypad Bus LEDs....................................................................................9
Programming (PROG) Connection ..................................................9
Keypad Addressing ................................................................................9
Overcurrent OVC LED ...........................................................................9
Wire Smoke and Glassbreak Detector Output -
Terminal 11 ............................................................................. 10
Wire Burglary Zones - Terminals 12 - 24........................ 10
Operational Parameters......................................................................10
Zone Voltages Using 2.2k Ω Resistors ..........................................10
Zone Response Time ...........................................................................10
Keyswitch Arming Zone......................................................................10
Wire Powered Zone for 2-Wire Smoke Detectors -
Terminals 25 and 26............................................................. 11
Step 6: Wire Hardware Components...... 11
Wire for Annunciator Outputs........................................... 11
Harness Wiring........................................................................................ 11
Model 860 Relay Module .................................................................... 11
Connect to Public Telephone Network ...........................12
FCC Registration ................................................................................... 12
Notification.............................................................................................. 12
Connect to Ethernet ............................................................12
Ethernet LEDs ........................................................................................ 12
Reset the Panel .....................................................................13
Update Panel Software on Flash LOAD Jumper ...........13
Model 399 Cable (Remote Link Only)........................................... 13
Model 401 USB Flash Module........................................................... 14
Connect to Cell .................................................................... 14
Connect to Wi-Fi ................................................................. 14
Wire for On-Board 1100 Series
Wireless Antenna Connection.......................................... 15
Wireless Antenna .................................................................................. 15
LED Operation........................................................................................ 15
CONTENTS
Get Started ....................................................1
How to Read This Guide .......................................................1
Caution Notes............................................................................................1
Compliance Instructions........................................................................1
What's Included......................................................................1
What You'll Need....................................................................1
System Components ...................................2
Wiring Diagram...................................................................... 2
Lightning Protection............................................................. 2
Accessory Devices.................................................................2
XT30/XT50 Wiring Diagram...............................................4
Step 1: Mount the Enclosure ..................... 5
Step 2: Mount the Keypads.......................6
Mounting Keypads ................................................................6
Understanding Keypad Specifications .............................6
Step 3: Wire the Power Supply ................ 7
Wire the Primary Power Supply......................................... 7
AC Terminals 1 and 2 ..............................................................................7
Transformer Type ....................................................................................7
Power LED .................................................................................................7
Wire the Secondary Power Supply ................................... 7
Battery Terminals 3 and 4....................................................................7
Earth Ground ............................................................................................7
Replacement Period...............................................................................7
Discharge/Recharge..............................................................................8
Battery Supervision................................................................................8
XT30/XT50 Power Requirements.....................................................8
XT30/XT50 Standby Battery Calculations ....................................8
Step 5: Wire the Terminals........................9
Wire for Bell Output - Terminals 5 and 6.........................9
Wire the Keypad Data Bus -
Terminals 7, 8, 9, and 10 .......................................................9
Terminal 7 - RED......................................................................................9

Step 7: Install Wireless Keypads ............ 16
Mount the Keypads ............................................................. 16
Associate Wireless Keypads............................................. 16
LCD Wireless Keypad .......................................................................... 16
Wireless Graphics Touchscreen Keypad....................................... 16
Power/Armed LED ................................................................................ 16
Listed Compliance Specifications........... 17
Bypass Reports .....................................................................17
Current Draw .........................................................................17
Battery Standby....................................................................17
Auxiliary and Bell Current ..................................................17
Cross Zoning..........................................................................17
App Key ..................................................................................17
Compliance................................................. 18
Household Burglar-Alarm System Units -
ANSI/UL 1023....................................................................... 18
Digital Burglar Alarm Communicator System Units -
ANSI/UL 1635 ....................................................................... 18
Central Station Burglar Alarm Units -
ANSI/UL 1610........................................................................ 19
Household Fire Warning System -
ANSI/UL 985 NFPA 72 Specifications............................ 19
California State Fire Marshal Specifications ................ 20
False Alarm Reduction Programmable Options -
ANSI/SIA CP-01-2010..........................................................21
Shipping Defaults and Recommended Programming ............ 21
Call Waiting............................................................................21
Entry Delay.............................................................................21
Local Bell...............................................................................22
Minimum Installation Requirements ...............................22
Troubleshooting ........................................23
Troubleshooting Section ...................................................23
Common LCD Keypad Displays........................................23
Wiring Diagrams........................................24
Multiple Indicating Circuit Modules Installation ..........24
System Sensor 2-Wire Smoke Detectors.......................25
Specifications.............................................26
Power Supply .......................................................................26
Enclosure...............................................................................26
Communication....................................................................26
Keypads/Expansion ............................................................26
Panel Zones...........................................................................26
Number of Zones.................................................................27
Outputs ..................................................................................27
Certifications..............................................27
ETL Listed..............................................................................27
FCC Information ..................................................................28
Industry Canada Information............................................28

XT Series Installation Guide | Digital Monitoring Products 1
GET STARTED
The panel can be programmed to operate as any of the following system types:
▶All/Perimeter system that provides one perimeter area and one interior area
▶Home/Sleep/Away system that provides one perimeter, one interior, and one bedroom area. The bedroom area
provides for any protection devices the user wants disarmed during their sleeping hours and armed as Away.
▶Six area system that provides areas of protection that can be independently armed or disarmed.
How to Read This Guide
Caution Notes
Throughout this guide you will see caution notes containing information you need to know when installing the
panel. These cautions are indicated with a yellow lightning bolt. Whenever you see a caution note, make sure
you completely read and understand its information. Failing to follow the caution note can cause damage to the
equipment or improper operation of one or more components in the system.
Compliance Instructions
For applications that must conform to a local authorities installation standard or a National Recognized Testing
Laboratory certificated system, please see "Listed Compliance Specifications" near the end of this guide for additional
instructions.
What's Included
Your kit or package may include more devices and accessories than what is shown below.
What You'll Need
▶Drill
▶Pliers
▶Wire connectors
XT Panel Documentation Enclosure Lock and Key
(ordered separately)
Hardware Pack

XT Series Installation Guide | Digital Monitoring Products 2
SYSTEM COMPONENTS
Wiring Diagram
The system wiring diagram in "Figure 1: System Wiring Diagram" shows some of the accessory devices for use in
various applications. A description of each module follows.
Lightning Protection
Metal Oxide Varistors and Transient Voltage Suppressors help protect against voltage surges on input and output
circuits. This transient protection provides additional resistance to electrical surges such as lighting. Additional surge
protection is available by installing the DMP 370 or 370RJ Lightning Suppressors.
Accessory Devices
CELLULAR COMMUNICATOR CARDS
263LTE Series Cellular
Communicator
Allows you to connect the XT30/XT50 Series to the Verizon or AT&T LTE network. Panel firmware Version 212 or
higher required.
263EXT Cellular Extension
Module
Allows you to remote the cell module away from the panel.
ZONE AND OUTPUT EXPANSION MODULES
710 Bus Splitter/Repeater Increases keypad wiring distance to 2500 feet.
711, 711S Single Point Zone
Expander
Provides one Class B zone for burglary devices and non-powered fire devices.
712-8 Zone Expander Provides 8 zones for burglary devices.
714, 714-8, 714-16 Zone Expander Provides Class B zones for burglary and non-powered fire devices.
715, 715-8, 715-16 Zone Expander Provides 12 VDC Class B powered zones for smoke detectors, glassbreak detectors, and other 2- or 4-wire devices.
860, 860-4 Relay Output Module Provides one relay and three relay sockets for expansion of up to four relays.
INTERFACE MODULE
734 Wiegand Interface Module Provides arming, disarming, and codeless entry using access control readers.
738Z+ Z-Wave Interface Module Provides connection for Z-Wave modules.
WI-FI MODULE
763 Module Allows you to add Wi-Fi alarm signal communication to XT30/XT50 panels, version 124 or higher with Level L
hardware.
KEYPADS
7000 Series Thinline™ and
Aqualite™ Keypad
Allows you to control the panel from various remote locations. Connect up to eight keypads.
Model 7060, 7063, 7070, 7073, 7160, 7173 Thinline™ keypads, 7060A and 7073A Aqualite™ keypads, 7360, 7363
Thinline Icon Series keypads to the keypad bus using terminals 7, 8, 9, and 10.
7800 Series Graphic Touchscreen
keypads
Allows you to control the panel from various remote locations. Connect up to eight keypads.
7872 and 7873 Graphic Touchscreen keypads
9000 Series Wireless LCD
keypads
Allows you to control the panel from various remote locations. Connect up to seven keypads.
9060, 9063 Wireless Keypads.
9800 Series Wireless Graphic
Touchscreen keypads
Allows you to control the panel from various remote locations. Connect up to seven keypads.
9862 Wireless Keypads.

XT Series Installation Guide | Digital Monitoring Products 3
DMP TWO-WAY WIRELESS DEVICES
1100D/1100DE/1100DH/
1100DHE/1100DI Receiver
Supports transmitters in residential or commercial wireless operation on the keypad bus.
1100R/1100RE Repeater Provides additional range for wireless devices.
1100T Translator Allows upgrades of non-DMP systems with one way, low frequency, wireless transmitters to DMP.
1101/1101E Universal Transmitter Provides both internal and external contacts that may be used at the same time to yield two individual reporting
zones from one wireless transmitter. Provides Disarm/Disable functionality.
1102 Universal Transmitter Provides one external contact. Provides Disarm/Disable functionality.
1103/1103E Universal Transmitter Provides both internal and external contacts that may be used at the same time to yield two individual reporting
zones from one wireless transmitter. Requires EOL resistor for external contact. Provides Disarm/Disable
functionality.
1106/1106E Universal Transmitter Provides both internal and external contacts that may be used at the same time to yield two individual reporting
zones from one wireless transmitter. Provides Disarm/Disable functionality.
1107 Micro Window Transmitter* Provides a window transmitter and magnet.
1108 Doorbell Module* The 1108 Doorbell Module monitors doorbell button presses.
1114 Four-Zone Expander* Provides four wireless zones with EOL resistors.
1115 Temperature Sensor
and Flood Detector*
Temperature and flood detector with an internal temperature sensor. Can be paired with 470PB or T280R
remote sensors.
1116 Relay Output* Provides one Form C relay.
1117 LED Annunciator* Provides a visual system status indicator.
1119 Door Sounder* Provides a battery operated sounder.
1122 PIR Motion Detector* Provides motion detection with pet immunity.
1126R PIR Motion Detector* Ceiling mount motion detector with panel programmable sensitivity and Disarm/Disable functionality.
1127C/1127W PIR Motion Detector Wall mount motion detector with panel programmable sensitivity and Disarm/Disable functionality.
1128 Glassbreak Detector* Detects the shattering of framed glass mounted in an outside wall and provides full-pattern coverage and false-
alarm immunity.
1131 Recessed Contact* Provides concealed protection for doors, windows or other applications.
1134 Access Control Module Allows you to use the access control capability of DMP Panels using smartcard, proximity, mag stripe, or
biometric readers, or other compatible authentication devices.
1135/1135E Siren* Provides a wireless siren.
1136 Remote Chime The 1136 Wireless Remote Chime is a multi-function sounder that plugs directly into a standard 110 VAC wall
outlet.
1137 LED Emergency Light Provides path lighting in the event of an alarm or trouble such as Burglary Alarm Output or can be activated
simultaneously by the panel via the Trip with Panel Bell feature.
1139 Bill Trap* Provides a silent alarm option for retail and banking cash drawers.
1141 Wall Button* One button wall mounted wireless transmitter.
1142BC Two-button Panic Belt
Clip Transmitter
Provides portable two-button panic operation.
1142 Two-button Panic Transmitter Provides permanently mounted under-the-counter two-button panic operation
1144-4 (Four-Button)*
1144-2 (Two-Button)
1144-D (Dual-Button)*
1144-1 (One-Button)*
Key Fob transmitters designed to clip onto a key ring or lanyard.
1148 Personal Pendant* One button one-button, wireless emergency transmitter designed to be worn as a wristband or on a break-away
lanyard.
1154 4-Zone Input Module* Converts up to four existing normally closed, hardwired zones into wireless zones.
1158 Eight-Zone Input Module* Converts up to eight existing normally closed, hardwired zones into wireless zones.
1164/1164NS Commercial Smoke Battery powered, wireless, low profile, photoelectric smoke detector. The 1164 also oers a synchronized
sounder.
1166 Smoke Ring Installed with any traditional AC-powered interconnected smoke detector system and provides an audible alert
in the event of a fire.
1168 CO/Smoke Detector Wireless CO/Smoke/Low Temp detector.
1183-135F Heat Detector Fixed temperature heat detector.
1183-135R Heat Detector Fixed temperature and rate-of-rise heat detector.
1184 Carbon Monoxide Detector Carbon Monoxide Detector.
* These devices have not been investigated and shall not be used in listed installations.

XT Series Installation Guide | Digital Monitoring Products 4
16 to 18
gauge wire
MAXIMUM AC
WIRE DISTANCE
16 gauge wire: 70 feet
18 gauge wire: 40 feet
Earth Ground
s
s
s
s
RED
BLACK
USE MARKING
Commercial Central Station;
Household Fire and Burglar
Warning System Control Unit
(DACT, PSDN: IP or Cellular)
NFPA 72
This equipment should be installed in
accordance with Chapter 11 of the
National Fire Alarm Code,
ANSI/NFPA 72-2002, (National Fire
Protection Association, Batterymarch
Park, Quincy, MA 02269). Printed
information describing proper
installation, operation, testing,
maintenance, evacuation planning,
and repair service is to be provided
with this equipment. Warning:
Owner’s instruction notice, not to be
removed by anyone except occupant.
HOUSEHOLD FIRE WIRING
Recognized limited energy cable
must be used for connection of all
initiating, indicating, and
supplementary devices.
POWER LIMITED
All circuits on the Model XT30/XT50
comply with the requirements for
inherent power limitation and are
Class 2.
TYPES OF SERVICE
Suitable for DACT Central Station.
Suitable for Household Fire and
Household Burglary. Test weekly.
SIA CP-01-2010 minimum system
is XT30 or XT50, local Bell, and
o premise DACT communication
to an SCS-1R receiver plus
ANSI/SIA CP-01-2010 classified
compatible DMP keypads as
indicated in the installation guide.
Z7
21
LISTED RESISTORS
1.0k Ohm - DMP Model 311
3.3k Ohm - DMP Model 309
Plug into
120VAC
60 Hz
outlet not
controlled
by switch.
ZONE 10 COMPATIBILITY IDENTIFIER
A
MAXIMUM OPERATING RANGE
8.8 VDC - 14.2 VDC
AUXILIARY OUTPUT
Minimum voltage on Auxiliary output to
process Sensor trips is 10.4VDC.
EXP HEADER
The 763 Wi-Fi Module connects to
XT30/XT50 panel using the included
cable and operates at 12 VDC from the
panel power supply.
DMP TRANSFORMERS
Model 321:
16.5 VAC 40 VA Class 2 plug-in.
Verification
Zone 10
Control Unit
Delay
13.6 sec.
Smoke
Model
______
Detector
Delay
____sec.
Heat detectors, manual pull stations, or any
other shorting device. Unlimited number of
units.
1k or 2.2k Ohm EOL on each zone
Switched Voltage Output
ZONE 10
Keypad
Bus
SMOKE
ZONES 1-9
Bell
SECONDARY POWER SUPPLY
1.2 Amps maximum charging current.
Use only 12 VDC rechargeable batteries.
Replace every 3 to 5 years.
For Wireless Devices, Control Unit delay is 0 (zero).
BELL
10.2 - 13.9VDC
Total current:
1.5 Amps max. w/ 40 VA
AUX (RED)
Up to 500 mA auxiliary current
at
10.2 VDC - 13.9 VDC from
Terminal 7
Up to 325 mA auxiliary current
at 10.2 VDC - 13.9 VDC from
Terminal 7 when using (2) Model
364 1.3 Ah Batteries
SMOKE OUTPUT
100 mA at 10.2 - 13.9 VDC
Terminal 11 LISTED APPLICATIONS
For listed applications the maximum current from a combination of bell
output and auxillary output is 1.6 amps.
AC Wiring must be in
conduit and exit out the
left side of the enclosure.
Wiring on terminals 5-26
must exit right and
maintain a 1/4" separation
from the AC and battery
positive wiring.
PHONE LINE
OUTPUTS
ETHERNET
RESET
Wirel
ess Antenna
Con
nection
RJ Supervision
1
2
3
4
LOAD
RED
PROG
XT30/XT50 Series Panel
Programming Header
Use DMP Model 330 Harness
Terminals 5-20 are Power Limited.
CELL
Smoke
Detector
1k Ohm
ss
To Keypad
or Zone Expander
Zone 1
1k/2.2k
Ohm
Zone 2
Zone 3
Zone 4
Zone 5
Zone 6
Zone 7
Zone 8
3.3k Ohm Resistor
DMP Model 309
Zone
10
1k/2.2k
Ohm
1k/2.2k
Ohm
1k/2.2k
Ohm
1k/2.2k
Ohm
1k/2.2k
Ohm
1k/2.2k
Ohm
1k/2.2k
Ohm
AC
1
AC
2
B+
3
B-
4
BELL
5
GND
6
S S
S
S
S
S
S
S
SS
S
S
S
S
RED
7
EXP
YEL
8
GRN
9
BLK
10
SMK
11
Z1
12
GND
13
Z2
14
Z3
15
GND
16
Z4
17
Z5
18
GND
19
Z6
20
Z7
21
GND
22
Z8
23
Z9
24
Z10+
25
Z10-
26
s
Surge protectors
S
S
S
S
XT30/XT50 Wiring Diagram
Figure 1: System Wiring Diagram

XT Series Installation Guide | Digital Monitoring Products 5
STEP 1: MOUNT THE ENCLOSURE
The metal enclosure must be mounted in a secure, dry place to protect the panel from damage due to tampering or
the elements. It is not necessary to remove the PCB when installing the enclosure. The PCB may be installed in the
standard 340 Small enclosure, optional 341 Kiosk enclosure, optional 349 Medium enclosure, or the optional 349A
Attack enclosure.
Seconds paragraph (cut)
When using cellular communication or on-board wireless with the
341 enclosure, an SMA and wireless antenna exit may be added at
the time of the installation. The 349A Attack Resistant enclosure is
factory shipped with one knockout on the top left of the enclosure.
As needed, additional knockouts may be added at the time of
installation. See Figure 3 for the positions on the enclosure that can
be added. Each additional knockout must be filled with conduit.
Slide panel PCB into lower enclosure slots
Model 349 Enclosure
Slide panel PCB between formed metal supports
Enclosure Mounting Holes
Panel PCB screws
Model 340 Enclosure
PHONE
OUTPUTS
1
2
3
4
ETHERNET
RESET
Wireless
Antenna
connection
RJ
Supervision
Cellular
header for
263
Module
Cellular Antenna
Connection
65555
LOAD
RED
PROG
Battery Shelf
Dual 1/2” and 3/4” Conduit Knockouts
Battery Shelf
PHONE
OUTPUTS
1
2
3
4
ETHERNET
RESET
Wireless
Antenna
connection
RJ
Supervision
Cellular
header for
263
Module
Cellular Antenna
Connection
65555
LOAD
RED
PROG
Panel PCB screws
Dual 1/2” and 3/4” Conduit Knockouts
Enclosure Mounting Holes
EXP
EXP
3-Hole
Pattern for
Accessory
Modules
349A Optional Knockout
Front and Rear Tamper
Switches for 350A Attack
Resistant Enclosure
Dual 1 3/4" and 1 3/8" Conduit Knockouts
Battery Shelf
Model 349A Enclosure
Slide panel PCB between formed metal supports
PHONE
OUTPUTS
1
2
3
4
ETHERNET
RESET
RJ Supervision
Cellular Header for
263 Module
LOAD
PROG
RED
EXP
Lid Mounting Holes (4 places)
Lid Mounting Holes (4)
Enclosure Mounting Holes (4 places)
PEMs for optional
battery bracket
Dual 1/2" and 3/4" Conduit Knockouts
Tamper Mounting Holes
(Upper and Lower)
Openings drilled
at installation
Model 341 Enclosure
PHONE
OUTPUTS
1
2
3
4
ETHERNET
RESET
Wireless Antenna
connection
RJ Supervision
Cellular Header
for 263 Module
LOAD
PROG
Power
LED
OVC LED
XMIT
RCV
TX RX
Wireless LEDs
EXP
Figure 2: Standard 340 Enclosure (left), Optional 349 Enclosure (right)
Figure 3: Optional 341 Enclosure (left), Optional 349A Enclosure (right)

XT Series Installation Guide | Digital Monitoring Products 6
STEP 2: MOUNT THE KEYPADS
Mounting Keypads
DMP keypads have removable covers that allow the base to be mounted on a wall or other flat surface using the screw
holes provided on each corner.
For mounting keypads on solid walls, or for applications where conduit is required, use a DMP 695 or 696 keypad
conduit backbox.
Understanding Keypad Specifications
Several factors determine the performance characteristics of the keypad bus: the length of wire used, the number
of devices connected, and the voltage at each device. When planning a keypad bus installation, keep in mind the
following four specifications:
▶DMP recommends using 18- or 22-gauge unshielded wire for all keypad circuits. Do not use twisted pair or
shielded wire for keypad bus data circuits.
▶On keypad bus circuits, to maintain auxiliary power integrity when using 22-gauge wire do not exceed 500
feet. When using 18-gauge wire do not exceed 1,000 feet. To increase the wire length or to add devices, install
an additional power supply.
▶Maximum distance for any one bus circuit (length of wire) is 2,500 feet regardless of the wire gauge. This
distance can be in the form of one long wire run or multiple branches with all wiring totaling no more than
2,500 feet. As wire distance from the panel increases, DC voltage on the wire decreases.
▶Maximum voltage drop between the panel (or auxiliary power supply) and any device is 2.0 VDC. If the voltage
at any device is less than the required level, add an auxiliary power supply at the end of the circuit. When
voltage is too low, the devices cannot operate properly.
For additional information refer to the 710 Installation Sheet (LT-0310) and or the LX-Bus/Keypad Bus Wiring
Application Note (LT-2031).

XT Series Installation Guide | Digital Monitoring Products 7
STEP 3: WIRE THE POWER SUPPLY
Wire the Primary Power Supply
AC Terminals 1 and 2
Connect the transformer wires to terminals 1 and 2 on the panel. Use no more than 70 ft. of 16 gauge, or 40 ft. of 18
gauge, wire between the transformer and the panel to deliver a minimum of 15.5 VAC when 500 mA of current draw is
used from the auxiliary power supply terminal 7.
Caution: Always ground the panel before applying power to any devices. The panel must be properly grounded
before connecting any devices or applying power to the panel. Proper grounding protects against Electrostatic
Discharge (ESD) that can damage system components. See "Earth Ground", in the Secondary Power Supply
section.
Transformer Type
The transformer for the panel is 16.5 VAC 40 VA. This provides up to 1.5 Amps of bell output current, 500 mA of
auxiliary current, and 100 mA of smoke detector output. Use either the 321 plug-in transformer with the panel. The
total current available is limited by the total battery standby requirements of the installation.
Caution:The transformer must be connected to a 120 VAC 60 Hz commercial power outlet that is not controlled
by a wall switch. Never share the transformer output with any other equipment.
Power LED
When either AC transformer power or DC battery power is connected to the panel the PWR LED shows steady green.
Wire the Secondary Power Supply
Battery Terminals 3 and 4
Connect the black battery lead to the negative battery
terminal. The negative terminal connects to the enclosure
ground internally through the XT30 or XT50 circuit board.
Connect the red battery lead to the positive battery terminal.
Observe polarity when connecting the battery.
Add a second battery in parallel using the DMP Model
318 Dual Battery Harness. DMP requires each battery be
separated by a PTC in the battery harness wiring to protect
each battery from a reversal or short within the circuit. See
Figure 4.
Caution: Use sealed lead-acid batteries only: Use 12 VDC sealed lead-acid rechargeable battery. Batteries
supplied by DMP have been tested to ensure proper charging with DMP products. Gel Cell batteries cannot be
used with the XT30/XT50 panel.
Earth Ground
Terminal 4 of the panel must be connected to earth ground using 14 gauge or larger wire to provide proper transient
suppression. DMP recommends connecting to a metal cold water pipe or ground rod only. Do not connect to electrical
conduit or a telephone company ground.
Replacement Period
DMP recommends replacing the battery every 3 to 5 years under normal use.
AC
1 2 3 4
+BAC –B
318 Battery Harness
Red
Black
Battery Battery
Panel Red
Panel Black
56
BELL GND
To AC
14 AWG to Earth Ground
XT30/XT50
Panel
PTC
To Bell Circuit
Figure 4: Wiring Multiple Batteries

XT Series Installation Guide | Digital Monitoring Products 8
Discharge/Recharge
The panel battery charging circuit float charges at 13.9 VDC at a maximum current of 1.2 Amps using a 40 VA
transformer. The total current available is reduced by the combined auxiliary current draw from terminals 7, 11, and 25.
The various battery voltage levels are listed below:
▶Battery Trouble: Below 11.9 VDC
▶Battery Restored: Above 12.6 VDC
Battery Supervision
The panel tests the battery once every hour when AC power is present. This test occurs 15 minutes past each hour and
lasts for five seconds. A load is placed on the battery and if its voltage falls below 11.9 VDC a low battery is detected.
If AC power has failed, a low battery is detected any time the battery voltage falls below 11.9 VDC.
If a low battery is detected with AC power present, the test is repeated every two minutes until the battery charges
above 12 VDC; the battery restored voltage. If a faulty battery is replaced with a fully charged battery, the restored
battery will not be detected until the next two-minute test is done.
XT30/XT50 Power Requirements
During AC power failure, the panel and all auxiliary devices connected draw their power from the battery. All devices
must be taken into consideration when calculating the battery standby capacity. On the following page is a list of
the power requirements of the panel. Add the additional current draw of DMP keypads, smoke detector output, and
any other auxiliary devices used in the system for the total current required. The total is then multiplied by the total
number of standby hours required to arrive at the total Amperehours required.
XT30/XT50 Standby Battery Calculations
For complete battery calculations, see the Battery Calculator.

XT Series Installation Guide | Digital Monitoring Products 9
STEP 5: WIRE THE TERMINALS
Wire for Bell Output - Terminals 5 and 6
Nominal 12 VDC is supplied by terminal 5 on the panel to power alarm bells or horns. The output is rated for a
maximum of 1.5 Amps with a 40 VA transformer. This output can be steady, pulsed, or Temporal Code 3 depending
upon the Bell Action specified in Bell Options programming. Terminal 6 is the ground reference for the bell circuit. If
using a horn or siren, a 1k 0hm resister should be added across the bell circuit for supervision.
Wire the Keypad Data Bus - Terminals 7, 8, 9, and 10
Terminals 7, 8, 9, and 10 of the panel are designated as the keypad data bus. In addition to keypads, the XT30/XT50
allows the connection of any combination of zone expansion modules, Glassbreak Detectors, and PIRs to the keypad
bus up to the maximum of eight devices.
Terminal 7 - RED
Nominal 12 VDC is supplied at terminal 7 to power keypads and zone expanders. This is also where power for any
auxiliary device is supplied. The ground reference for terminal 7 is terminal 10. The maximum output is rated at
500mA. All auxiliary devices totaled together must not exceed the Terminal 7 maximum current rating of 500 mA.
When the number of keypads or other expansion devices attached exceeds the amount of output current available,
attach an external power supply as defined in the 710 Installation Sheet (LT-0310).
Terminal 8 - YEL
Data receive from keypads and zone expanders.
Terminal 9 - GRN
Data transmit to keypads and zone expanders.
Terminal 10 - BLK
Terminal 10 is the ground reference for LCD keypads, zone expanders, and any auxiliary devices being powered by
terminals 7 and 11.
Keypad Bus LEDs
The two LEDs located just above terminal 13 indicate keypad transmit data (XMIT) and keypad receive data (RCV).
The bottom LED flashes green to indicate data being transmitted from the panel. The top LED flashes yellow to
indicate data being received by the panel from keypads, zone expanders, etc.
Programming (PROG) Connection
A locking 4-pin PROG header is provided to connect a keypad when
using a DMP Model 330 Programming Cable. This provides a quick and
easy connection for programming the panel.
Keypad Addressing
Keypad Bus expansion zones are numbered in groups of four
corresponding to the address. For example, address 1 is zones 11-14 and
address 5 is zones 51-54.
There are a maximum of 32 zones possible on the Keypad Bus. All keypad
zones terminate with a 1k 0hm EOL resistor.
Overcurrent OVC LED
The Overcurrent LED (OVC) lights Red when the devices connected to the
Keypad Bus draw more current than the auxiliary output rating. The OVC LED
is located above terminals 9 and 10 as shown in Figure 5. When the OVC LED
lights Red, the Keypad bus/auxiliary power (terminal 7) and the PROG header
shut down.
PHONE
RJ
Supervision
OVC LED
POWER
LED
AC
1
AC
2
B+
3
B-
4
BELL
5
GND
6
RED
7
YEL
8
GRN
9
BLK
10
SMK
11
Figure 5: OVC LED Location
ADDRESS XT30/XT50 ZONE NUMBER
1 11-14
2 21-24
3 31-34
4 41-44
5 51-54
6 61-64
771-74
8 81-84

XT Series Installation Guide | Digital Monitoring Products 10
Wire Smoke and Glassbreak Detector Output - Terminal 11
Nominal 12 VDC at 100 mA maximum (shared by terminal 25) is supplied at terminal 11 to power 4-wire smoke
detectors or other auxiliary powered devices. This output can be turned o by the user for 5 seconds using the Sensor
Reset option in the User Menu. Terminal 10 is the ground reference for terminal 11.
Wire Burglary Zones - Terminals 12 - 24
On XT30/XT50 panels, terminals 12 to 24 are the nine burglary zones. For programming purposes, the zone numbers
are 1 to 9. The zone configurations on terminals 12 to 24 are described below.
TERMINAL FUNCTION TERMINAL FUNCTION
12 Zone 1 voltage sensing 19 Ground for zones 5 & 6
13 Ground for zones 1 & 2 20 Zone 6 voltage sensing
14 Zone 2 voltage sensing 21 Zone 7 voltage sensing
15 Zone 3 voltage sensing 22 Ground for zones 7, 8, & 9
16 Ground for zones 3 & 4 23 Zone 8 voltage sensing
17 Zone 4 voltage sensing 24 Zone 9 voltage sensing
18 Zone 5 voltage sensing
The voltage sensing terminal measures the voltage across the 1k ohm End-of-Line resistor and the zone’s ground
terminal. Dry contact sensing devices can be used in series (normally-closed) or in parallel (normally-open) with any
of the burglary protection zones.
Operational Parameters
Each burglary protection zone detects three conditions: open, normal, and short.
The parameters for each are listed below:
CONDITION RESISTANCE ON ZONE VOLTAGE ON
ZONE TERMINAL
Open over 1300 ohms over 2.0 VDC
Normal 600 to 1300 ohms 1.2 to 2.0 VDC
Short under 600 ohms under 1.2 VDC
Zone Voltages Using 2.2k Ω Resistors
STATE VOLTAGE
Open ≥3 VDC
Normal 2.2 - 2.9 VDC
Short 0 - 2.1 VDC
Applies to zones 1-9 on XT Series panels with
version 193 firmware and higher
Zone Response Time
A condition must be present on a zone for 500 milliseconds before it is detected by the panel. Ensure detection
devices used on the protection zones are rated for use with this delay.
Keyswitch Arming Zone
You can use a momentary keyswitch on a zone programmed as an Arming type for use in arming and disarming the
system without a code.
1k Ohm Normally
Closed 1k Ohm Normally Open 1k Ohm Combination
Normally Open and
Normally Closed
Figure 6: Protection Zone Contact Wiring

XT Series Installation Guide | Digital Monitoring Products 11
Wire Powered Zone for 2-Wire Smoke Detectors - Terminals 25 and 26
A resettable 2-wire Class B powered zone is provided on terminals 25 (positive) and 26 (negative) of the panel. For
programming purposes, the zone number is 10 on the XT30/XT50. The zone uses a Model 309, 3.3k ohm EOL resistor
(provided with the panel) and has an operating range of 8.8 to 13.9 VDC.
The compatibility identifier is: B.
Caution: Sensor reset on zone 10 drops power to devices on this zone, causing the panel to sense an open
condition on all zone types other than Fire, Fire Verify, and Supervisory. Whenever non-Fire and non-Supervisory
zone types are used on zone 10, make the appropriate adjustments to the zone’s Armed Action to prevent false
alarms from occurring.
MANUFACTURER MODEL DETECTOR ID # OF DETECTORS ZONE EXPANSION MODULES
DMP/Hochiki SLR-835B HD-6 7 715, 715-8, 715-16, 725
Sentrol/ESL 429AT, 521B, 521BXT S09A 12 715, 715-8, 715-16
System Sensor 2WTA-B, 2WTR-B A 10 715, 715-8, 715-16
STEP 6: WIRE HARDWARE COMPONENTS
Use this section for reference when using any of these hardware components.
Wire for Annunciator Outputs
The four annunciator outputs can be programmed to indicate the activity of the panel’s zones or conditions occurring
on the system. Annunciator outputs do not provide a voltage but instead switch-to-ground voltage from another
source. The outputs can respond to any of the conditions listed below:
1. Activation by zone condition: Steady, Pulse, Momentary, or Follower
2. Manually from the keypad
3. Communication failure
4. Armed area annunciation
5. Fire Alarm or Fire Trouble
6. Ambush alarm
7. Exit and Entry timers
8. System Ready
9. Late to Close
Harness Wiring
The open collector outputs are accessible by installing the DMP 300 Harness on the
4-pin OUTPUTS header.
The output locations are shown below. For listed applications, devices connected to
outputs must be located within the same room as the panel.
Model 860 Relay Module
Connect a Model 860 Relay Module to the panel to provide relays for the annunciator outputs that can be used for
electrical isolation between the alarm panel and other systems or for switching voltage to control various functions.
The module includes one relay and provides three additional sockets for expansion of up to four relays. Power is
supplied to the relay coils from the panel keypad bus. The 860 mounts inside the panel enclosure using the 3-hole
mounting configuration. Plastic standos are provided with the module for ease of installation. A 4-wire harness is
also provided that connects the Model 860 to the panel. Relay Contact Rating: 1 Amp at 30 VDC
OUTPUT COLOR WIRE
1Red 1
2 Yellow 2
3 Green 3
4 Black 4

XT Series Installation Guide | Digital Monitoring Products 12
Connect to Public Telephone Network
Connect the panel to the public telephone network by installing a DMP 356 RJ Cable between the panel’s PHONE
LINE connector and the RJ31X or RJ38X phone jack.
Caution: To reduce the risk of fire, use only No. 26 AWG or larger telecommunication line cord, such as DMP
Model 356 Series Phone Cords.
A two pin RJ SUP header is provided to allow monitoring of the
telephone cable connected between the panel and a RJ38X jack
(pins 2 and 7 jumpered). Attach a DMP Model 306 Harness between
RJ SUP and any available zone. The RJ SUP pins are connected via
the telephone cable to the RJ38X jack pins 2 and 7. The RJ38X jack
provides a jumper between pins 2 and 7 which completes the circuit.
Program the zone as a Supervisory type (SV). When the telephone
cable is removed, the keypad displays zone trouble and produces a
steady tone.
FCC Registration
The panel complies with FCC part 68 and is registered with the FCC.
▶Registration number: CCKAL00BXT50
▶Ringer Equivalence: 0.0B
Notification
Registered terminal equipment must not be repaired by the user. In case of trouble, the device must be immediately
unplugged from the telephone jack. The factory warranty provides for repairs. Registered terminal equipment may not
be used on party lines or in connection with coin telephones. Notification must be given to the telephone company
with the following information:
▶The particular line(s) the service is connected to
▶The FCC registration number
▶The ringer equivalence
▶The make, model, and serial number of the device
Connect to Ethernet
The ETHERNET Connector is available on the Network version and connects directly to an Ethernet network using a
standard patch cable.
Ethernet LEDs
The two LEDs, located on the left side of the ETHERNET Connector, indicate network operation. The top, Link LED is a
steady green light when an ethernet cable is connected. The bottom, Activity LED flashes yellow to indicate messages
are being received or transmitted.
To Telephone
Line
RJ31X or RJ38X
Phone Block
8
7
6
54
3
2
1
Ring Tip
To Premise
Phone(s)
Ring 1
Tip 1
Figure 7: Phone Jack Wiring

XT Series Installation Guide | Digital Monitoring Products 13
Reset the Panel
The RESET header is located just above the terminal strip on the right side of the circuit board and is used to reset
the XT30/XT50 microprocessor. To reset the panel when first installing the system, install the reset jumper before
applying power to the panel. After connecting the AC and battery, remove the reset jumper.
To reset the panel while the system is operational, for example, prior to reprogramming, install the reset jumper
without powering down the system. Remove the reset jumper after one or two seconds.
After resetting the panel, begin programming within 30 minutes. If you wait longer than 30 minutes, reset the panel
again.
XT30/XT50 Panel
PHONE
LINE
OUTPUTS
1
2
3
4
Wireless Antenna
connection
RJ
Supervision
Momentarily place
the RESET jumper
over both of the
RESET pins to
reset the panel.
RESET
LOAD
ETHERNET
OVC LED
Power
LED
TX RX
Wireless LEDs
PROG
XMIT
RCV
CELL MODULE
AC
1
AC
2
B+
3
B-
4
BELL
5
GND
6
RED
7
YEL
8
GRN
9
BLK
10
SMK
11
Z1
12
GND
13
Z2
14
Z3
15
GND
16
Z4
17
Z5
18
GND
19
Z6
20
Z7
21
GND
22
Z8
23
Z9
24
Z10+
25
Z10-
26
Figure 8: Panel Showing the RESET Header
Update Panel Software on Flash LOAD Jumper
The XT Series panel software can be updated via the panel’s Programming (PROG) header. To update the panel with a
new software version, complete the following steps at the protected premise:
Model 399 Cable (Remote Link Only)
1. Place a jumper across the RESET header and then remove the yellow and green wires from keypad bus
terminals 8 and 9.
2. Connect a DMP update Cable from the PROG header to the serial port of your PC operating Remote Link and
containing the XT RU file. Requires Remote Link 1.43 or higher.
3. Start Remote Link and create or open the XT Series control panel account that matches the panel to be
updated.
4. Set the Connection Information Type to Direct with a baud rate of 38400 and choose the appropriate COM
port.
5. Select Panel > Remote Update, then select the correct RU file for the XT panel model.
6. While placing a short across the LOAD header, remove the jumper from the RESET header. Click Update in
Remote Link.
7. After the software version is updated, remove the short from the LOAD header. Place the jumper across RESET
then remove the 399 cable.
8. Replace the yellow and green wires to terminals 8 and 9.
9. Remove RESET jumper to resume normal panel operation.

XT Series Installation Guide | Digital Monitoring Products 14
Model 401 USB Flash Module
1. Place a jumper across the Reset header.
2. Remove the wires from the keypad bus terminals.
3. Place a jumper from across the Reset header.
4. Place a jumper across the Load header.
5. Connect the USB flash drive with the file (RU) to the Model 401. Connect the assembly to the panel’s PROG
header. The LED on the Model 401 will flash and display steady green.
6. Remove the jumper across the Reset header.
7. Press and release the button on the Model 401 to initiate the firmware update. The LED on the Model 401 will
flash slowly. If the LED displays fast flashes, it means the firmware update was unsuccessful. The update will last
up to five minutes. When complete, the LED on the Model 401 will display steady green.
8. Replace the jumper across the Reset header. Remove the USB flash drive and Model 401 assembly.
9. Remove the jumper from the Load header.
10. Remove the jumper from the Reset header
11. Reconnect the keypad bus wires.
Note: In the event the Model 401 USB Flash Module is inadvertently removed from the panel before the updated
finishes, repeat steps 1 through 10.
Connect to Cell
The CELL MODULE header is provided to connect a 263
Series Cellular Communicator. The cellular antenna connection
protrudes through the top of the enclosure. A brass washer is
required if installing a 263LTE Series to an XT50 Series panel.
Note: Do not misalign the cell module 12-pin connector
onto cell module header. If needed, the PCB can be
removed from the enclosure to allow placement of the
cell module.
Figure 9: Cellular and 1100 Series Wireless Antenna
Connections
Connect
antenna to
right side
only
Brass Washer
(XT50 using 263LTE Series)
RCV
XMIT
PROG
263LTE Cellular
Communicator
1100 Series
Antenna (XT50)
OUTPUTS
LOAD
TX RX
1100 Series
Wireless Antenna
Connection
Wireless LEDs
RESET
ETHERNET
BLK
10
SMK
11
Z1
12
GND
13
Z2
14
Z3
15
GND
16
Z4
17
Z5
18
GND
19
Z6
20
Z7
21
GND
22
Z8
23
Z9
24
Z10+
25
Z10-
26
1
2
3
4
EXP
Connect to Wi-Fi
The 763 Wi-Fi Module allows you to add Wi-Fi alarm signal
communication to XT30/XT50 panels. The 763 connects to
the 7-pin EXP header on compatible panels using the included
cable and operates at 12 VDC from the panel power supply.
The 763 Wi-Fi Module is compatible with all DMP XT30/XT50
Series control panels with Level L hardware and Version 124
or higher firmware.
Z4
17
Z5
18
GND
19
Z6
20
Z7
21
GND
22
Z8
23
Z9
24
Z10+
25
Z10-
26
Included 3ft cable
OUTPUTS
1
2
3
4
Wireless Antenna
connection
Cellular
Header
RESET
LOAD
TX RX
Wireless LEDs
EXP
Link LED
Figure 10: 763 to XT30/XT50 Series

XT Series Installation Guide | Digital Monitoring Products 15
Wire for On-Board 1100 Series Wireless Antenna Connection
Wireless Antenna
The XT50 Wireless Antenna (ANT) terminal block is located at the top right corner of the circuit board. The antenna
installs through a small opening in the top of the enclosure and is attached to the panel using the right terminal. The
left terminal is not used.
The XT50 built-in wireless operates with DMP 1100 Series transmitters. See "Accessory Devices".
LED Operation
Green (TX): With a wireless house code enabled, the green LED flashes every time the receiver transmits (32 times
per second). If a house code is not programmed in the panel, the panel is reset, or the panel is powered o, the green
LED will be o. Under normal operation, the green LED flashes constantly with no interruption or change.
Yellow (RX): The yellow LED flashes every time the receiver hears a message from a programmed wireless transmitter.
When a message is sent by a transmitter, typically by pressing or releasing the tamper switch, the yellow LED should
flash indicating that the receiver received a message from the transmitter. If the LED never flashes, the transmitter is
not getting through to the receiver. This could be because of a misprogrammed serial number or the transmitter is too
far away. Under normal operation, the yellow LED will flash at every trip of every wireless transmitter and occasionally
when the transmitters perform their periodic check-in. It is not unusual for this LED to stay o for many minutes at a
time when no transmitters are communicating.

XT Series Installation Guide | Digital Monitoring Products 16
STEP 7: INSTALL WIRELESS KEYPADS
Mount the Keypads
DMP keypads have removable covers that allow the base to be mounted on a wall, desk stand or other flat surface
using the screw holes provided on each corner.
Associate Wireless Keypads
Enable Wireless Keypad Association operation on both the keypad and panel. To enable association operation in the
XT30/XT50 panel, reset the panel three times allowing the keypad bus transmit light to begin flashing between each
reset.
For 60 seconds, the panel listens for wireless keypads that are in RF Survey and have not been programmed or
associated into another panel. Wireless keypads are assigned to the first open device position in Device Setup
automatically, based upon the order in which they are detected. The keypad logo turns Green to indicate it has been
associated with the panel.
Note: A maximum of seven wireless keypads are allowed on each panel.
LCD Wireless Keypad
1. Press and hold the Back Arrow key and CMD until SET BRIGHTNESS
displays.
2. Enter the code 3577 (INST) at the keypad and press CMD.
3. Press KPD RF to start the RF survey communication. The keypad
displays its wireless serial number and RF SURVEY.
Wireless Graphics Touchscreen Keypad
1. Access the Options menu through the carousel menu.
2. While in the Options display, press the Installer Options icon.
3. Enter the code 3577 (INST) at the keypad and press CMD.
4. Press KPD RF to start the RF survey communication. The keypad displays its wireless serial number and RF
SURVEY.
Power/Armed LED
The keypad Power/Armed LED turns Red, indicating communication
has not yet been established with the panel receiver. When successful
communication has been established, the Power/Armed LED turns Blue on
Graphics keypads or Green on LCD keypads.
KPD KPD KPD
OPT DIAG RF STOP
S/N * * * * * * * *
RF SURVEY
Figure 11: Keypad Screen Installer Options
Figure 12: Transmit and Receive LEDs
PROG
XMIT
RCV
SMK
11
Z1
12
GND
13
Z2
14
Z3
15
GND
16
Z4
17