ABB ARG600 ANSI User manual

9
10
—
Quick Start Guide
ARG600/ARR600 Wireless Gateway
1LAN port(s)
2SIM card slot(s)
3Console/serial port
4DIP switches
5 Application serial port (RS2)
6Antenna connector FME (male)
7Power switch
8 Power supply 12...36 VDC
1
35
4
2 7
6
8
1 I/O connector (only ARR600 models)
2 Power supply 12...48 VDC
3Console/serial port
4Power switch
5Console/serial port switch
6DIP switches
7 Application serial port (RS2)
8LAN port(s)
9Antenna connector SMA (female)
10 SIM card slot(s)
1
3
54
27
6
8

2
QUICK START GUIDE ARG600/ARR600 WIRELESS GATEWAY
—
Getting started
Power-up and SIM card installation
Insert the SIM card. Push the yellow button in the SIM card
slot to eject the SIM card tray. Insert the SIM card to the
tray (contacts facing up) and push it firmly and carefully
back to its holder. Attach the power supply and switch the
device on. Under normal circumstances, the device is able
to automatically connect to the operator’s cellular network.
In problem situations you can log in to the Arctic Web
userinterface by using Web browser and navigating to
Network → Mobile WAN.
If your SIM card requires a PIN code, do not install
it before you have configured the Arctic device
PIN code settings.
Login to the Arctic Web user interface
Connect the Ethernet cable between the Arctic device
LAN port and your computer.
Configure your computer to use the same IP address space
as the Arctic device. For example, your computer IP could
be 10.10.10.11 with netmask 255.255.255.0. Check the
connection with the ping command.
Connect to the Arctic device using the web browser.
The default address of the Arctic device is https://10.10.10.10/.
Remember to use https and not http.
Accept the self-signed certificate in the browser.
Log in to the device. The username is arctic-adm and the
default password is arcticm2m.
It is highly recommended that the default password
is changed before the product is connected to a public
cellular network.
—
Figure 1. Browser https example
—
Figure 2. Welcome page in the ARG600 Web user interface

QUICK START GUIDE ARG600/ARR600 WIRELESS GATEWAY
3
Wireless network settings
Log in to the Arctic Web user interface using your
Web browser.
Navigate to Network → Mobile WAN.
Change the APN type from ”Automatic” to ”Manual”.
Set the Access Point Name (APN) appropriately (usually
INTERNET or operatorname.com). As this setting depends
on your mobile operator, ensure the APN settings directly
from the operator.
Set the other settings such as the PIN code, authentication,
username and password if required by the operator’s
subscription.
Reboot the Arctic device and check the settings and the
cellular network connection status from System → Status.
Complete customer documentation is available in
the product pages that can be accessed through
abb.com/mediumvoltage
—
Figure 3. Mobile WAN settings

1MRS758863 REV B EN 02-2019
—
We reserve the right to make technical changes or modify the contents
of this document without prior notice. With regard to purchase orders,
the agreed particulars shall prevail. ABB does not accept any responsibility
whatsoever for potential errors or possible lack of information in this
document.
We reserve all rights in this document and in the subject matter and
illustrations contained therein. Any reproduction, disclosure to third
parties or utilization of its
contents – in whole or in parts – is forbidden
without prior written consent of ABB.
Copyright© 2019 ABB. All rights reserved.
—
For more information, please contact
ABB Distribution Solutions
P.O. Box 699
FI-65101 Vaasa, Finland
Phone: + 358 10 22 11
abb.com/mediumvoltage
abb.com/substationautomation