Dinstar DAG2000-16S User manual

Quick Installation Guide
DAG2000-16S
DAG2000-24S
DAG2000-32S
欢迎您选购鼎信通达旗下产品！
安装设备之前请仔细阅读本安装指导。鼎信通达为客户提供全方位的技术支持，需要更多在线
技术支持，请拨打技术支持热线电话：[phone]。
网址：www.dinstar.cn
THANKS FOR CHOOSING DINSTAR’S VOIP GATEWAY!
Please read this guide carefully before installing the gateway. If you need any technical
support, .please contact us
Tel: [phone]
Email: [e-mail]
Web: www.dinstar.com

Please confirm your product model before installation and follow the installation
guideline for the model.
Product Model & Number of Ports
1
Description of Indicators
2
Indicator Definition Status Description
Power Indicator
Running Indicator
Telephone In-use
Indicator
On
On
On
Off
Off
Off
Off
The gateway is powered on
The gateway is powered off or there is no
power supply
Off
Slow Flashing
Green Flashing
Network Link
Indicator
Network Speed
Indicator
PWR
RUN
FXS
LAN
The gateway is running properly
If there is a SIP account registered
successfully, the indicator is fast flashing
The gateway is running improperly
FXS port is currently occupied by a call
FXS port is idle or faulty
The gateway is properly connected to network
Work at 100Mbps
Work at 10Mbps
Fast Flashing
Model
Port Type
DAG2000-16S
Network Port RJ11 RJ21
0
316
24
32
3
3
1
2
DAG2000-24S
DAG2000-32S
For the DAG 2000 series product, FXS Ports support two types, RJ11 or RJ21. Please
check the table above for the number of ports on specific product models;
The gateway is not connected to network or
network connection is improper way
Indicators and Ports
3
DAG2000-16S
Power Indicator
Running Indicator
Telephone In-use
Indicator
FXS Ports 0-15(RJ11)

DAG2000-24S/32S
Power
Switch
Power Switch
Power
Jack
LAN Ports
LAN Ports
Console
Port
Reset Button
Grounding Lug
Grounding Lug
FXS Ports 0-31 (RJ11)
FXS Ports ( RJ21)
Note: The position of each indicator and interface of DAG2000-24S is the same as on the
DAG2000-32S.
Reset
Button
Telephone In-use Indicator
Power Jack Console Port
100-240VAC
50/60Hz
100-24 0VAC 5 0/60Hz
Installation Attentions
4
When installing the device, please confirm the type of telephone interface of the device:
DAG2000-16S is equipped with RJ11 ports;
DAG2000-24S/32S is equipped with both RJ11 and RJ21 ports;
Please go to Wire Sequence of this guideline to get more information about wire sequence.
Anti-jamming: to reduce the interference with telephone calls, it's highly recommended that telephone
lines connected to the gateway should be placed away from power cables.
Power supply: the power adapter of the gateway accepts 100-240V AC power supply. Please ensure
safe and stable power supply.
Network bandwidth: please ensure there is enough network bandwidth so as to guarantee stabilized
running of the gateway.
Temperature and humidity: to avoid any accident that might cause malfunction, it's advised to install
the gateway in an equipment room where temperature and humidity are appropriate.
Ventilation: to avoid overheating, please do not pile up the gateway with other devices and make sure
the gateway has good ventilation around.
Mechanical load: please make sure the gateway is placed steadily to avoid damage. It's highly
advised to horizontally place the gateway on a flat surface or a cabinet.
Power Indicator
Running Indicator

Connect gateway with power input and grounding lug
Installation Instructions
5
Connection Diagram for DAG2000-16S
Connect gateway with network via a switch
Connect FXS ports with analog phones
Connect gateway with power input and grounding lug
RJ11 telephone line
Telephone
AC 100-240V
Grounding
Cable
Grounding Lug
Network Cable
Switch
Network Cable P C
Connection Diagram forDAG2000-24S/32S
Connect gateway with network via a switch
Connect FXS ports(RJ21) with analog phones
100-240V AC
100-240VAC 50/60Hz
Grounding Cable
Grounding Lug
Network Cable
Switch
Network Cable
PC
Telephone
RJ21 Cable

Connect FXS ports(RJ11) with analog phones
Telephone
RJ11 Cable
Wire Sequence
6
·Rj21 Wire Sequence
DAG2000-24S/32S support RJ21 Interfaces for FXS connections. One RJ21 cable
has 25 pairs of wires, but the 25 pair of wires never used. It means that RJ21 interface
only support 24 pairs of RJ11 interfaces.
Call No.
Colour
PIN No.
White
P1
0
Blue
P26
1 2 34
White Orange White Green White Brown White Slate
P2
P27 P3 P28 P4 P29 P5 P30
Call No.
Colour
PIN No.
Red
P6
5
Blue
P31
68 9
Orange Green Brown Slate
P7 P32 P8
P33 P9 P34
P10
P35
7
Red Red Red Red
Call No.
Colour
PIN No.
Black
P11
10
Blue
P36
11 12 13 14
Orange Green Brown Slate
P12 P37 P13 P38 P14
P39
P15
P40
Black Black Black Black
Call No.
Colour
PIN No.
Yellow
P16
15
Blue
P41
16 17 18 19
Orange Green Brown Slate
P17
P42
P18
P43 P19 P44 P20 P45
Yellow Yellow Yellow Yellow
Call No.
20
21 22
23 24
Colour Violet Blue Orange Green Brown Slate
Violet Violet Violet Violet
PIN No.
P21
P46
P22
P47 P23 P48 P24 P49 P25
P50

Modify PC’s IP Address
7
Log in Web Management System
8
To log in the Web Management System of the gateway, you need to modify the IP
address of PC first to make it at the same network segment with the gateway.
On the P C, click ‘Network (or Ethernet) → Properties’.
Double-click ‘Internet Protocol Version 4 (TCP/IPv4)’.
Select ‘Use the following I P address’, and then enter an available IP address
‘192.168.11.XX X’ which is at the same network segment with ‘192.168.11.1’.
1
2
3
Open a web browser and enter the gateway's IP address (default IP is
192.168.11.1). Then, input username and password in the displayed login GUI.
Both the default username and password are admin.

Modify Gateway’s IP Address
9
Configure Gateway
10
Click Save and then restart the gateway for the new configurations to take effect.
(1) Configure SIP Server
(2) Configure SIP Account Information
If you want to modify the IP address of DAG1000-1S/2S/4S, please click 'Network
→ Local Network' in the navigation tree on the left of the Web Management
System, and then input new IP address and DNS server address on the displayed
interface.
Log in the Web Management System of the gateway, and then click SIP Server in
the navigation tree and then enter the address of the SIP server which is to be
registered. Click Save in the last.
Click Port in the navigation tree on the left, and then click Add. Input the SIP
account and authentication password assigned by the SIP server.

Basic Operations
11
More Details
12
This document only provides instructions for quick installation and basic
configuration, For detailed configuration and parameter explanation, please
refer to user manual or ask for online technical support.
Dial *158# to query the IP address of LAN port of the gateway;
Dial *159# to query the IP address of WAN port of the gateway;
Dial *114# to query the telephone number of a FX S port;
Dial *165*000000# to restore default IP address, username and password;
Restore factory default settings:
(1) dial *166*000000#;
(2) press the R ST button for 7 seconds;then restart by manual;
(3) Log in the gateway and then click ‘Tools → Factory Reset’ , then click Apply
and restart the gateway.
Dial *111# to restart the gateway.
IP COMMUNICATION SOLUTIONS
Shenzhen Dinstar Co., Ltd.
Web: www.dinstar.com