Directed VW02 Use and care manual

Directed Digital System
VW02
Firmware Specific Guide
This product is intended for installation by a professional
installer only! Attempts to install this product by a person
other than a trained professional may result in severe
damage to a vehicle’s electrical system and components.
© 2016 Directed, Vista, CA
Directed Digital System 2016-11

Contents
Warning! Safety first ....................................................................................................................... 3
Introduction .................................................................................................................................... 4
Vehicle application guide ........................................................................................................... 4
Wiring connections ......................................................................................................................... 5
Main power harness (H1), 12-pin thick gauge connector ............................................................... 5
Auxiliary output harness (H2), 16-pin black connector .................................................................. 5
Analog harness (H3), 18-pin white connector .............................................................................. 6
MC501 harness (H4), 8 thick-gauge wires (optional)..................................................................... 6
Immobilizer interface ...................................................................................................................... 7
Method 1: Immobilizer interface with 556U (Regular Key) ............................................................. 7
Method 2: Immobilizer interface with 556U Push-to-Start (PTS)........................................................ 7
Method 3: Key wrap for Regular Key........................................................................................... 8
Method 4: Key wrap for Regular Key - Alternate ........................................................................... 8
Method 5: Key wrap for Push-To-Start (PTS)................................................................................... 9
Method 6: Key wrap for Push-To-Start (PTS) - Alternate ................................................................... 9
Method 7: Key wrap for Key Port (Types 5 and 6 only)................................................................ 10
Installation.................................................................................................................................... 11
Type 1 - Regular Key ............................................................................................................... 11
Type 2 - Push-To-Start ............................................................................................................... 12
Type 3 - Regular Key................................................................................................................ 13
Type 4 - Regular Key................................................................................................................ 14
Alternate clutch connection for Audi R8 (Type 4) ......................................................................... 15
Type 5 - Key Port..................................................................................................................... 16
Type 6- Key Port...................................................................................................................... 17
Type 7 - Regular Key................................................................................................................ 18
Type 8- Push-To-Start ............................................................................................................... 19
Type 9 - Regular Key................................................................................................................ 20
Type 10- Push-To-Start .............................................................................................................. 21
Type 11 - Regular Key.............................................................................................................. 22
Vehicle wiring reference charts ....................................................................................................... 23
Connecting the module .................................................................................................................. 24
Important! .............................................................................................................................. 24
Manual or automatic transmission selection ................................................................................ 24
Optional sensors ..................................................................................................................... 25
RF kits.................................................................................................................................... 25
When used in conjunction with SmartStart.................................................................................. 25
Module programming.............................................................................................................. 26
LED diagnostics and troubleshooting.......................................................................................... 28
Module reset .......................................................................................................................... 29
Learning the Tach (not needed with Virtual Tach) ............................................................................... 30
Initializing Virtual Tach (not needed with hardwired or data tach applications) ..................................... 30
Limited lifetime consumer warranty .................................................................................................. 31
Quick Reference Guide – Viper, Clifford, Python, Avital & Automate (Regular Key)................................ 32
Quick Reference Guide – Autostart (Regular Key).............................................................................. 35
Quick Reference Guide – Viper, Clifford, Python, Avital & Automate (Smart Key) .................................. 38
Quick Reference Guide – Autostart (Smart Key) ................................................................................ 41

3Directed Digital System VW02
© 2016 Directed. All rights reserved.
Warning! Safety first
The following safety warnings must be observed at all times:
• Due to the complexity of this system, installation of this product must only be performed by an authorized
Directed dealer.
• When properly installed, this system can start the vehicle via a command signal from the remote control.
Therefore, never operate the system in an area that does not have adequate ventilation.
The following precautions are the sole responsibility of the user; however, authorized Directed dealers should:
• Never use a test light or logic probe when installing this unit. Always use a multimeter.
• Never operate the system in an enclosed or partially enclosed area without ventilation (such as a garage).
• When parking in an enclosed or partially enclosed area or when having the vehicle serviced, the
remote start system must be disabled using the installed toggle switch. It is the user’s sole responsibility to
properly handle and keep out of reach from children all remote controls to assure that the system does not
unintentionally remote start the vehicle.
• USER MUST INSTALL A CARBON MONOXIDE DETECTOR IN OR ABOUT THE LIVING AREA ADJACENT
TO THE VEHICLE. ALL DOORS LEADING FROM ADJACENT LIVING AREAS TO THE ENCLOSED OR
PARTIALLY ENCLOSED VEHICLE STORAGE AREA MUST REMAIN CLOSED AT ALL TIMES.
Use of this product in a manner contrary to its intended mode of operation may result in property damage,
personal injury, or death. Except when performing the Safety Check outlined in this installation guide, (1) Never
remotely start the vehicle with the vehicle in gear, and (2) Never remotely start the vehicle with the keys in the
ignition. The user is responsible for having the neutral safety feature of the vehicle periodically checked, wherein
the vehicle must not remotely start while the car is in gear. This testing should be performed by an authorized
Directed dealer in accordance with the Safety Check outlined in this product installation guide. If the vehicle
starts in gear, cease remote start operation immediately and consult with the user to fix the problem immediately.
OPERATION OF THE REMOTE START MODULE IF THE VEHICLE STARTS IN GEAR IS CONTRARY TO ITS
INTENDED MODE OF OPERATION. OPERATING THE REMOTE START SYSTEM UNDER THESE CONDITIONS
MAY RESULT IN PROPERTY DAMAGE OR PERSONAL INJURY. IMMEDIATELY CEASE THE USE OF THE UNIT
AND REPAIR OR DISCONNECT THE INSTALLED REMOTE START MODULE. DIRECTED WILL NOT BE HELD
RESPONSIBLE OR PAY FOR INSTALLATION OR REINSTALLATION COSTS.
Remote starters for manual transmission pose significant risks if not properly installed and operated. When testing
to ensure the installation is working properly, only remote start the vehicle in neutral gear, on a flat surface and
with a functional, fully engaged parking brake. Do not allow anyone to stand in front of or behind the vehicle.
This product should not be installed in any convertible vehicles, soft or hard top with a manual transmission.
Installation in such vehicles may pose certain risk.

4Directed Digital System VW02
© 2016 Directed. All rights reserved.
Introduction
The VW02 firmware for Directed Digital Systems is a complete solution for remote start,
security (if applicable) and convenience needs compatible with specific Audi and Volkswagen
vehicles.
Warning! This module can only be programmed via the web tool, which can be found on
www.directechs.com or using the Directechs Mobile application for smartphones. Features
and functions will become accessible when you connect the module using the XKLoader.
Vehicle application guide
The following table lists the vehicles and features which are compatible with this product. The number assigned
to each year allows you to determine which installation type should be used for your vehicle.
Note: This firmware does not support transponder override. One (1) programmed OEM key must be wired
into the vehicle to complete installation of a remote starter.
Vehicles
2016 2015 2014 2013 2012 2011 2010 2009 2008 2007 2006 2005 2004 AV-Turn Signal ON/OFF Control CC-Comfort Closure windows DL-Arm Factory Security DL-Disarm Factory Security DL-Door Lock Control DL-Door Unlock DL-Driver Priority Unlock DL-Trunk / Hatch Release FOB-Control of aftermarket alarm with OEM remote RS-3x LOCK START (Start control using OEM Remote) RS-3x LOCK STOP (Stop control using OEM Remote) RS-RAP Shut Down (Retained ACC Power) RS-SmartStart RS-SmartStart 3.0 Compatible RS-Tach / RPM Output SS-Entry Monitoring ALL Door Pins SS-Entry Monitoring Driver Door Pin SS-Entry Monitoring Hood Pin SS-Entry Monitoring Trunk/Hatch Pin ST-Brake Status (foot brake) ST-E-Brake Status * ST-Ignition Status
Audi
A3 4 4 4 4 1 or 4 11111
••••••••••••••••••••••
A3 Cabriolet 1 1 1
••••••••••••••••••••••
Q3
11 11 •••••• •• • •• ••••
Q3 (Smart Key) 2
2 •••••• •• • •• ••••
R8 4 4 4 4 4 1 1
••••••••••••••••••••••
TT 44444 4 1 11
••••••••••••••••••••••
Volkswagen
Beetle
999
••••••••••••••••••••••
Beetle (Smart Key) 888
••••••••••••••••••••••
EOS 11 11 11 11 11 1 1 1 1
••••••••••••••••••••••
EOS (Smart Key)
222
•••••• •• • •• ••••
Golf 3333 3 or 4 1 1 1 1
••••••••••••••••••••••
Golf (Smart Key) 222
••••••••••••••••••••••
Jetta 77777 1 or 7 1 1 1 1
••••••••••••••••••••••
Jetta (Smart Key) 10 10 10 10 10
••••••••••••••••••••••
Jetta GLI (Smart Key) 22222
••••••••••••••••••••••
Passat 3335 5 5 555
••••••••••••••••••••••
Passat (Smart Key) 222
••••••••••••••••••••••
Passat CC
6 6 6 6 5 5 5
••••••••••••••••••••••
Rabbit 1 1 1 1
••••••••••••••••••••••
Tiguan 3333 3
••••••••••••••••••••••
Tiguan (Smart Key)
2 2
••••••••••••••••••••••
* For the E-Brake sensing to become active, start the vehicle, activate and release the E-brake once.
Legend:
DL: OE Door Lock & Alarm Controls
FOB: Sync CAN Interface w/ FOB Remote
RS: Remote Start & Engine Controls
SS: Integrated Security & Monitoring
ST: Function/Feature Status
Note: This firmware does not support transponder override. One (1) programmed OEM key must be wired into the vehicle to complete installation of a remote starter.
AV: Horn & Lights Controls
CC: Comfort & Light Controls

5Directed Digital System VW02
© 2016 Directed. All rights reserved.
Wiring connections
The wiring connections listed below are specific to this firmware.
Main power harness (H1), 12-pin thick gauge connector
Conn./Pin Color Description
H1/1 White Relay 3 COM – (+) 12 Volt (Battery) 1
H1/2 White/Brown Relay 3 N.O. – (+) Ignition Output 1
H1/3 Brown/Red Relay 2 N.O. – Key Wrap
H1/4 Yellow/Red Relay 2 COM – Key Wrap
H1/5 Orange/Red Relay 2 N.C. – Key Wrap
H1/6 Yellow Relay 1 COM – Clutch (Manual Transmission ONLY) 1
H1/7 White Relay 3 COM – No Connection 1
H1/8 White/Brown Relay 3 N.O. – No Connection 1
H1/9 Black (-) Ground
H1/10 Red (+) 12 Volt (Battery)
H1/11 Orange/Yellow Relay 1 N.C. – Clutch (Manual Transmission ONLY) 1
H1/12 Brown Relay 1 N.O. – Clutch (Manual Transmission ONLY) 1
Auxiliary output harness (H2), 16-pin black connector
Conn./Pin Color Description
H2/1 Violet/Brown Door Locks
H2/2 Yellow/Black No Connection
H2/3 Orange/Black (-) Clutch Output
H2/4 Tan HS CAN Low
H2/5 Tan/Black HS CAN High
H2/6 Light Green No Connection
H2/7 Orange/Green FT CAN High
H2/8 Orange/Brown FT CAN Low
H2/9 Violet/Green Door Locks
H2/10 Green/Black (-) Hazards Switch Output 2
H2/11 White/Violet No Connection 2
H2/12 White/Red (+) Accessory Output 2
H2/13 Lt. Blue/Black (-) PTS Output 2
H2/14 Green/Red (+) Brake Activation Output or (+) Starter Output 2
H2/15 N/A No Connection
H2/16 Violet/Yellow No Connection
1. If these outputs are not used by the firmware, they can be configured by the installer when the module is flashed.
2. If these outputs are not used by the firmware, they can be configured by the installer when the module is flashed. Note that they are
low current and a relay may be necessary.

6Directed Digital System VW02
© 2016 Directed. All rights reserved.
Analog harness (H3), 18-pin white connector
Conn./Pin Color Description
H3/1 Lt. Blue/Red No Connection
H3/2 Black/White (-) Parking Brake Input (Manual Transmission) 2
H3/3 Gray (-) Hood Input 2
H3/4 N/A No Connection
H3/5 Gray/Black (+) Glow Plug Input 2
H3/6 Violet/White (AC) Tach Input 2
H3/7 Dark Blue (-) Clutch Output (Manual Transmission)
H3/8 Brown/Black Horn1
H3/9 Red/White (-) Trunk Release Output 1
H3/10 White/Green (-) Door Input 2
H3/11 Yellow/Green (+) Door Input 2
H3/12 Blue/Red No Connection
H3/13 Light Blue (-) Trunk Trigger Input 2
H3/14 Pink/Yellow (-) Activation (Start Trigger) Input
H3/15 Dark Green Lock 1
H3/16 Brown/White (+) Brake Input 2
H3/17 Brown (+) Siren Output 1
H3/18 Blue/White (-) GWR (Ground While Running) 1
MC501 harness (H4), 8 thick-gauge wires (optional)
Conn./Pin Color Description
H4/1 Pink/White No Connection
H4/2 Red/White No Connection
H4/3 Pink No Connection
H4/4 Red No Connection
H4/5 Orange No Connection
H4/6 Red No Connection
H4/7 Green No Connection
H4/8 Violet No Connection
1. If these outputs are not used by the firmware, they can be configured by the installer when the module is flashed. Note that they are
low current and a relay may be necessary.
2. These connections are only required if the corresponding statuses are not supported by the firmware. See "Vehicle application guide"
on page 4 for a list of compatible features.

7Directed Digital System VW02
© 2016 Directed. All rights reserved.
Immobilizer interface
For vehicles with Keyless Entry you must remove battery from OEM key (the OEM remote may differ from the
models shown in the illustrations).
Method 1: Immobilizer interface with 556U (Regular Key)
556U or 556UW is sold SEPARATELY.
Move the 556U loop as close to the
front of ignition cylinder (OEM
Immobilizer Receiver) as possible.
Test and secure mounted loop
before reassembling the vehicle.
4
8
(+) 12V
OEM
Immobilizer
Receiver
16 Black 3 Wh
4 White 12 White4 Red
7 White 2 Wh
2 Bk
6 Green
18 White
Manual/Auto. Transmission Type
Prog.
Button
4: Yellow/Red: COM Relay 2
3: Brown/Red: NO Relay 2
IMPORTANT!: Not all OEM remotes can be inserted in 556U because of their size.
Make sure the key will fit, otherwise it is recommended to use a different method.
(-)Ground:Black,pin1
N/A:Violet,pin3
(-)GWR:Blue,pin4
N/A:Green,pin5
N/A:Brown,pin6
(+)12V:Red,pin2
Method 2: Immobilizer interface with 556U Push-to-Start (PTS)
556U or 556UW is sold SEPARATELY.
Note: OEM immobilizer receiver is located on
the underside of the steering column, where
the ignition switch would normally be.
4
8
(+) 12V
IMPORTANT!: Not all OEM remotes can be inserted in TBXKEY because of their size.
Make sure the key will fit, otherwise it is recommended to use a different method.
OEM
Immobilizer
Receiver
4: Yellow/Red: COM Relay 2
3: Brown/Red: NO Relay 2
Move 556U loop as close to the
front of ignition cylinder (OEM
Immobilizer Receiver) as possible.
Test and secure mounted loop
before reassembling the vehicle.
(-)Ground:Black,pin1
N/A:Violet,pin3
(-)GWR:_Blue,pin_4
N/A:Green,pin5
N/A:Brown,pin6
(+)12V:Red,pin2
16 Black 3 Wh
4 White 12 White4 Red
7 White 2 Wh
2 Bk
6 Green
18 White
Manual/Auto. Transmission Type
Prog.
Button

8Directed Digital System VW02
© 2016 Directed. All rights reserved.
Method 3: Key wrap for Regular Key
- Make 4-6 loops and place them as close to the front of key port (OEM Immobilizer Receiver) as possible.
- Test and secure mounted loops before reassembling the vehicle.
- Make 4-6 loops and place them around the front of the plastic body of the vehicle’s coded key as shown above.
* When possible use valet key for key wrap, if blade key is used, battery must be removed.
16 Black 3 Wh
4 White 12 White4 Red
7 White 2 Wh
2 Bk
6 Green
18 White
Manual/Auto. Transmission Type
Prog.
Button
4-6 loops
4-6 loops
4: Yellow/Red: COM Relay 2
3: Brown/Red: NO Relay 2
OEM
Immobilizer
Receiver
*
Method 4: Key wrap for Regular Key - Alternate
Blue
Brown
Immobilizer ECU
16 Black 3 Wh
4 White 12 White4 Red
7 White 2 Wh
2 Bk
6 Green
18 White
Manual/Auto. Transmission Type
Prog.
Button
4: Yellow/Red: COM Relay 2
3: Brown/Red: NO Relay 2
5: Orange/Red: NC Relay 2
Remove battery
from OEM
Remote Control
OEM
Immobilizer
Receiver
4-6 loops
- Make 4-6 loops and place them around the front of the plastic body of the vehicle's coded key as shown above.
- Test and secure mounted loops before reassembling the vehicle.
- Make connections to the OEM Immobilizer receiver as shown above.
* When possible use valet key for key wrap, if blade key is used, battery must be removed.

9Directed Digital System VW02
© 2016 Directed. All rights reserved.
Method 5: Key wrap for Push-To-Start (PTS)
- Make 4-6 loops and place them as close to the front of key port (OEM Immobilizer Receiver) as possible.
- Test and secure mounted loops before reassembling the vehicle.
- Make 4-6 loops and place them around the front of the plastic body of the vehicle’s coded key as shown above.
- When possible use valet key for key wrap, if blade key is used, battery must be removed.
16 Black 3 Wh
4 White 12 White4 Red
7 White 2 Wh
2 Bk
6 Green
18 White
Manual/Auto. Transmission Type
Prog.
Button
4-6 loops
4: Yellow/Red: COM Relay 2
3: Brown/Red: (-) Ground
OEM
Immobilizer
Receiver
Remove battery from
OEM Remote Control
4-6 loops
Volkswagen Jetta, Tiguan, Passat,
Beetle and Audi Q3
Volkswagen Golf and EOS
Method 6: Key wrap for Push-To-Start (PTS) - Alternate
Blue
Brown
Immobilizer ECU
16 Black 3 Wh
4 White 12 White4 Red
7 White 2 Wh
2 Bk
6 Green
18 White
Manual/Auto. Transmission Type
Prog.
Button
4: Yellow/Red: COM Relay 2
3: Brown/Red: NO Relay 2
5: Orange/Red: NC Relay 2
Remove battery from
OEM Remote Control
OEM
Immobilizer
Receiver
4-6 loops
- Make connections to the OEM Immobilizer Receiver as shown above.
- Test and secure mounted loops before reassembling the vehicle.
- Make 4-6 loops and place them around the front of the plastic body of the vehicle’s coded key as shown above.
Volkswagen Jetta, Tiguan, Passat,
Beetle and Audi Q3
Volkswagen Golf and EOS

10 Directed Digital System VW02
© 2016 Directed. All rights reserved.
Method 7: Key wrap for Key Port (Types 5 and 6 only)
- Make 4-6 loops and place them as close to the front of key port (OEM Immobilizer Receiver) as possible.
- Test and secure mounted loops before reassembling the vehicle.
- Make 4-6 loops and place them in between trunk and unlock button of the plastic body of the vehicle's coded key as
shown above.
16 Black 3 Wh
4 White 12 White4 Red
7 White 2 Wh
2 Bk
6 Green
18 White
Manual/Auto. Transmission Type
Prog.
Button
4-6 loops
4-6 loops
4: Yellow/Red: COM Relay 2
3: Brown/Red: NO Relay 2
Remove battery from
OEM Remote Control
Lt.Blue/Black
(at key port)

11 Directed Digital System VW02
© 2016 Directed. All rights reserved.
Installation
Type 1 - Regular Key
16 Black 3 Wh
4 White 12 White4 Red
7 White 2 Wh
2 Bk6 Green
18 White
Manual/Auto. Transmission Type Prog.
Button
Manual/Auto. Transmission Type Prog.
Button
FT CAN High: Orange/Green: 7
FT CAN Low: Orange/Brown: 8
10: Red: (+) 12V (+) 12V
[2] (+) Siren Output: Brown: 17
9: Black: (-) Ground
With the exception of the OBDII diagnostic connector, all connectors are displayed from the wire side (unless specified otherwise).
Siren
[1] The installation of an aftermarket hood pin is only required on vehicles that are not equipped with a factory hood pin.
[3] For Key Wrap instructions refer to pages 7-10.
[4] For manual transmission vehicle only.
Hood Pin
[1] (-) Hood Input: Gray: 3
6542 31
12
11
89 107
(+) Starter: Red/Black
or Black, pin1
(+) Ignition: Black or
Black/Green, pin 11
FT CAN Low: Orange/ Brown, pin 7
FT CAN High: Orange/Green, pin 8
[4] (-) Clutch: Violet/Black, pin 7
VESCM - Driver side,
under dashboard
E plug
at VESCM
G plug
at VESCM
FH GE
16
8
9
1
10
2
11
3
12
4
13
5
14
6
15
7
4: Yellow/Red: Key Wrap [3]
5: Orange/Red: Key Wrap [3]
3: Brown/Red: Key Wrap [3]
2: White/Brown: (+) Ignition Output
1: White: (+) 12V
(+) Starter Output: Green/Red: 14
The Remote Start
Safety Override
Switch MUST be in
the ON position.
Remote Start Safety
Override Switch
(-) Ground
(-) Clutch Output: Dk.Blue: 7
[2] The siren is only compatible with Directed Digital Hybrid Systems.

12 Directed Digital System VW02
© 2016 Directed. All rights reserved.
Type 2 - Push-To-Start
Refer to "Vehicle wiring reference charts" on page 23 for more information on vehicle-specific connections
[2] (+) Siren Output: Brown: 17
9: Black: (-) Ground
Siren
(-) Ground
Hood Pin
[1] (-) Hood Input: Gray: 3
FT CAN High: Orange/Green: 7
FT CAN Low: Orange/Brown: 8
(-) Hazards SW Output: Green/Black: 10
[5] (+) Brake Activation Output: Green/Red: 14
(-) Hazards: Brown/Red, pin 7
B
CA
VESCM -Driver side underdashboard
12
29
28
42 25 1
52 41 24 11
(connect this wire ONLY if turn
signals don’t flash via CANBUS)
[5] (+) Brake: Black/Red, pin 17
[4] (-) Clutch: Violet/White
or Violet/Black, pin 30
2 x 1Amp
Diodes
FT CAN High:
Orange/Green,
pin 16
FT CAN Low:
Orange/Brown, pin 15
14
1
9
8
16
[4] (-) Clutch Output: Dk. Blue: 7
(-) PTS Output: Lt. Blue/Black: 13
Located under steering column at
Control Unit for Electronic Steering Column Lock
C plug (Brown)
at VESCM
4: Yellow/Red: Key Wrap [3]
5: Orange/Red: Key Wrap [3]
3: Brown/Red: Key Wrap [3]
[6] (-) PTS: pin 13
[6] (-) PTS: pin 4
The Remote Start
Safety Override
Switch MUST be in
the ON position.
Remote Start Safety
Override Switch
With the exception of the OBDII diagnostic connector, all connectors are displayed from the wire side (unless specified otherwise).
[1] The installation of an aftermarket hood pin is only required on vehicles that are not equipped with a factory hood pin.
[3] For Key Wrap instructions refer to pages 7-10.
[4] For manual transmission vehicle only. For wire colors, refer to the Vehicle Wiring Reference Chart on page 23.
[5] For automatic transmission vehicle only.
10: Red: (+) 12V (+) 12V
16 Black 3 Wh
4 White 12 White4 Red
7 White 2 Wh
2 Bk6 Green
18 White
Prog.
Button
Manual/Auto. Transmission Type Prog.
Button
[6]
For wire colors, refer to the Vehicle Wiring Reference Chart on page 23.
[2] The siren is only compatible with Directed Digital Hybrid Systems.
.

13 Directed Digital System VW02
© 2016 Directed. All rights reserved.
Type 3 - Regular Key
Refer to "Vehicle wiring reference charts" on page 23 for more information on vehicle-specific connections.
[2] (+) Siren Output: Brown: 17
Siren
Hood Pin
FT CAN High: Orange/Green: 7
FT CAN Low: Orange/Brown: 8
(-) Hazards SW Output: Green/Black: 10
B
CA
VESCM-Driver side underdashboard
10: Red: (+) 12V (+) 12V
9: Black: (-) Ground (-) Ground
Steering Column Control Unit
12
29
28
42 25 1
52 41 24 11
FT CAN Low: Orange/Brown, pin 3
(+) Ignition:
Black, pin 14
[5] (+) Starter: pin 6
FT CAN High: Orange/Green, pin 4
[4] Clutch Output: Dk.Blue: 7
[1] (-) Hood Input: Gray: 3
(+) Starter Output: Green/Red: 14
2: White/Brown: (+) Ignition Output
1: White: (+) 12V
C plug (Brown)
at VESCM
(-) Hazards: Brown/Red, pin 7
(connect this wire only if turn
signals don’t work on CAN)
[4],[5] (-) Clutch: pin 30
4: Yellow/Red: Key Wrap
[3]
5: Orange/Red: Key Wrap [3]
3: Brown/Red: Key Wrap [3]
6
14
18
916
The Remote Start
Safety Override
Switch MUST be in
the ON position.
Remote Start Safety
Override Switch
With the exception of the OBDII diagnostic connector, all connectors are displayed from the wire side (unless specified otherwise).
[1] The installation of an aftermarket hood pin is only required on vehicles that are not equipped with a factory hood pin.
[3] For Key Wrap instructions refer to pages 7-10.
[4] For manual transmission vehicles only.
16 Black 3 Wh
4 White 12 White4 Red
7 White 2 Wh
2 Bk6 Green
18 White
Manual/Auto. Transmission Type Prog.
Button
Manual/Auto. Transmission Type Prog.
Button
[5]
For wire colors, refer to the Vehicle Wiring Reference Chart on page 23.
[2] The siren is only compatible with Directed Digital Hybrid Systems.
30
86 85
87
87a
(+) 12V
Fuse 5A
(+) Brake: Black/Red, pin 17
Note: Connect only on vehicle
where brake needs to be
depressed to start.

14 Directed Digital System VW02
© 2016 Directed. All rights reserved.
Type 4 - Regular Key
Refer to "Vehicle wiring reference charts" on page 23 for more information on vehicle-specific connections.
17
10
1
20
[2] (+) Siren Output: Brown: 17
Siren
Hood Pin
FT CAN High: Orange/Green: 7
FT CAN Low: Orange/Brown: 8
(-) Hazards SW Output: Green/Black: 10
B
CA
Steering Column Control Unit
12
29
28
42 25 1
52 41 24 11
(+) Starter: Red/Black
or Black/Gray, pin 18
FT CAN Low: Orange/Brown, pin 15
FT CAN High:
Orange/Green,
pin 14
[5] (+) Ignition: pin 17
[4] Clutch Output: Dk.Blue: 7
[1] (-) Hood Input: Gray: 3
(+) Starter Output: Green/Red: 14
2: White/Brown: (+) Ignition Output
1: White: (+) 12V
10: Red: (+) 12V (+) 12V
9: Black: (-) Ground (-) Ground
(-) Hazards:
Brown/Red or Blue/Red, pin 7
(connect this wire only if turn
signals don’t work on CAN)
[4] (-) Clutch:
Violet/Black,
pin 30
For Audi R8, see
Alternate connection
on the next page
VESCM-Driver side underdashboard
C plug (Brown)
at VESCM
4: Yellow/Red: Key Wrap [3]
5: Orange/Red: Key Wrap [3]
3: Brown/Red: Key Wrap [3]
The Remote Start
Safety Override
Switch MUST be in
the ON position.
Remote Start Safety
Override Switch
With the exception of the OBDII diagnostic connector, all connectors are displayed from the wire side (unless specified otherwise).
[1] The installation of an aftermarket hood pin is only required on vehicles that are not equipped with a factory hood pin.
[3] For Key Wrap instructions refer to pages 7-10.
[4] For manual transmission vehicle only.
16 Black 3 Wh
4 White 12 White4 Red
7 White 2 Wh
2 Bk6 Green
18 White
Manual/Auto. Transmission Type Prog.
Button
Manual/Auto. Transmission Type Prog.
Button
[5] For wire colors, refer to the Vehicle Wiring Reference Chart on page 23.
[2] The siren is only compatible with Directed Digital Hybrid Systems..

15 Directed Digital System VW02
© 2016 Directed. All rights reserved.
Alternate clutch connection for Audi R8 (Type 4)
466094 73
7
28 1
5
1
15
(-) Clutch:
Green/Gray,
pin 41
(-) Clutch:
Gray/Blue,
pin 39
Engine Control Module (ECM)
located at the front right of the engine
compartment
(-) Clutch Output: Dk. Blue: 7
16 Black 3 Wh
4 White 12 White4 Red
7 White 2 Wh
2 Bk6 Green
18 White
Manual/Auto. Transmission Type Prog.
Button
Manual/Auto. Transmission Type Prog.
Button
2x 1Amp Diodes

16 Directed Digital System VW02
© 2016 Directed. All rights reserved.
Type 5 - Key Port
FT CAN High: Orange/Green: 7
FT CAN Low: Orange/Brown: 8
[2] (+) Siren Output: Brown: 17
Siren
Hood Pin
[1] (-) Hood Input: Gray: 3
8
16
7
15
6
14
5
13
4
12
3
11
2
10
1
9
CUT
6542 31
12
11
10
87
[4] (-) Clutch:
Violet/Black, pin 7
FH GE
16
8
9
1
10
2
11
3
12
4
13
5
14
6
15
7
[4] (-) Clutch Output: Dk.Blue: 7
(-) Key In Output: Blue/White: 18
30
86 85
87
87a
10: Red: (+) 12V (+) 12V
9: Black: (-) Ground
2: White/Brown: (+) Ignition Output
1: White: (+) 12V
(+) 12V
(-) Ground
(+) Starter Output: Green/Red: 14
VESCM - Driver side, under dashboard
Ignition Switch Plug
(located at Key Port)
E plug
at VESCM
G plug
at VESCM
(+) Starter: Red/Gray
or Red/Violet, pin1
(+) Ignition:
Red/Violet,
pin 11
FT CAN Low:
Orange/ Brown,
pin 7
Keysense: Green,
pin 16
(+) 12V Interrupt: Green/Red, pin 3
FT CAN High:
Orange/Green, pin 8
4: Yellow/Red: Key Wrap [3]
5: Orange/Red: Key Wrap [3]
3: Brown/Red: Key Wrap [3]
The Remote Start
Safety Override
Switch MUST be in
the ON position.
Remote Start Safety
Override Switch
With the exception of the OBDII diagnostic connector, all connectors are displayed from the wire side (unless specified otherwise).
[1] The installation of an aftermarket hood pin is only required on vehicles that are not equipped with a factory hood pin.
[3] For Key Wrap instruction refer to pages 7-10.
[4] For manual transmission vehicle only.
16 Black 3 Wh
4 White 12 White4 Red
7 White 2 Wh
2 Bk6 Green
18 White
Manual/Auto. Transmission Type
Prog.
Button
Manual/Auto. Transmission Type Prog.
Button
[2] The siren is only compatible with Directed Digital Hybrid Systems..
(-) Hazards SW Output: Green/Black: 10
12
29
28
42 25 1
52 41 24 11
(+) Brake:
Black/Red,
pin 17
C plug (Brown)
at VESCM
30
86 85
87
87a
9
(-) Hazards: Brown/Red, pin 9
(connect this wire only if turn
signals don’t work on CAN)
(+)12V
Fuse 10A
Note: Connect only on vehicle
where brake needs to be
depressed to start.
Diode
1A

17 Directed Digital System VW02
© 2016 Directed. All rights reserved.
Type 6
30
86 85
87
87a
[2] (+) Siren Output: Brown: 17
Siren
Hood Pin
FT CAN High: Orange/Green: 7
FT CAN Low: Orange/Brown: 8
(-) Hazards SW Output: Green/Black: 10
(+) Starter Output: Green/Red: 14
(-) Key In Output: Blue/White: 18
B
CA
VESCM TypeB-Driver side underdashboard
10: Red: (+) 12V (+) 12V
9: Black: (-) Ground
2: White/Brown: (+) Ignition Output
1: White: (+) 12V
(-) Ground
6
14
18
916
Steering Column Control Unit
CPlug(Brown)
atVESCM
12
29
28
42 25 1
52 41 24 11
(+) Ignition:
Red/Green or Red/Violet, pin 5
Keysense: Green
or Green/Blue,
pin 16
(+) Starter:
Red/Brown or
Red/Gray,
pin 6
(+) 12V
FT CAN High: Orange/Green, pin 15
FT CAN Low: Orange/Brown,pin 16
(+) Brake: Black/Red,pin 17
Note: Connect only on
vehicle where brake
needs to be
depressed to start.
[4] (-) Clutch Output: Dk.Blue: 7
[1] (-) Hood Input: Gray: 3
Fuse 5A
(-) Hazards: Brown/Red, pin 7
(connect this wire only if turn
signals don’t work on CAN)
Ignition Switch Plug
(located at Key Port)
4: Yellow/Red: Key Wrap [3]
5: Orange/Red: Key Wrap [3]
3: Brown/Red: Key Wrap [3]
Clutch Pedal Switch
[4] (-) Clutch:
Violet/Black,
pin 4 [4] (-) Clutch:
White/Red, pin 2
12345
The Remote Start
Safety Override
Switch MUST be in
the ON position.
Remote Start Safety
Override Switch
With the exception of the OBDII diagnostic connector, all connectors are displayed from the wire side (unless specified otherwise).
[1] The installation of an aftermarket hood pin is only required on vehicles that are not equipped with a factory hood pin.
[3] For Key Wrap instructions refer to pages 7-10.
[4] For manual transmission vehicle only.
16 Black 3 Wh
4 White 12 White4 Red
7 White 2 Wh
2 Bk6 Green
18 White
Manual/Auto. Transmission Type Prog.
Button
Manual/Auto. Transmission Type Prog.
Button
[2] The siren is only compatible with Directed Digital Hybrid Systems..
30
86 85
87
87a
(+) 12V
Fuse 10A
- Key Port

18 Directed Digital System VW02
© 2016 Directed. All rights reserved.
Type 7 - Regular Key
FT CAN High: Orange/Green: 7
Door Locks: Violet/Brown: 1
Door Locks: Violet/Green: 9
FT CAN Low: Orange/Brown: 8
10: Red: (+) 12V (+) 12V
[2] (+) Siren Output: Brown: 17
9: Black: (-) Ground
Siren
(-) Ground
Hood Pin
Ignition
Switch
63
733716
17
1
63
73
3716
171
(-) Trunk Release Output: Red/White: 9
(-) Hazards SW Output: Green/Black: 10
B Plug
(White)
A Plug
(Black)
1 2 5
976 10
3
8
4
(+) Starter Output: Green/Red: 14
(+) Accessory Output: White/Red: 12
2: White/Brown: (+) Ignition Output
1: White: (+) 12V
[1] (-) Hood Input: Gray: 3
VESCM - Driver side,
under dashboard
B Plug (White)
at VESCM
A Plug (Black)
at VESCM
FT CAN Low:
Orange/Brown,
pin 21
[4] (-) Clutch: Violet/White or
Violet/Black, pin 55
(+) Accessory: Black/Red, pin 3 (+) Starter: Red/Black, pin 4
(+) Ignition: Black/Violet, pin 8
FT CAN High:
Orange/Green,
pin 20
(-) Hazards:
Brown/Red, pin 28
Arm/Disarm:
Blue/Red, pin 24
(-) Trunk Release:
Violet, pin 23
[4] (-) Clutch Output: Dk.Blue: 7
4: Yellow/Red: Key Wrap [3]
5: Orange/Red: Key Wrap [3]
3: Brown/Red: Key Wrap [3]
The Remote Start
Safety Override
Switch MUST be in
the ON position.
Remote Start Safety
Override Switch
With the exception of the OBDII diagnostic connector, all connectors are displayed from the wire side (unless specified otherwise).
[1] The installation of an aftermarket hood pin is only required on vehicles that are not equipped with a factory hood pin.
[3] For Key Wrap instructions refer to pages 7-10.
[4] For manual transmission vehicle only.
16 Black 3 Wh
4 White 12 White4 Red
7 White 2 Wh
2 Bk6 Green
18 White
Manual/Auto. Transmission Type Prog.
Button
Manual/Auto. Transmission Type Prog.
Button
[2] The siren is only compatible with Directed Digital Hybrid Systems..

19 Directed Digital System VW02
© 2016 Directed. All rights reserved.
Type 8- Push-To-Start
10: Red: (+) 12V (+) 12V
[2] (+) Siren Output: Brown: 17
(-) PTS Output: Lt. Blue/Black: 13
9: Black: (-) Ground
Siren
(-) Ground
Hood Pin
[1] (-) Hood Input: Gray: 3
FT CAN High: Orange/Green: 7
FT CAN Low: Orange/Brown: 8
(-) Hazards SW Output: Green/Black: 10
[5] (+) Brake Activation Output: Green/Red: 14
(-) Hazards: Brown/Red, pin 28
(connect this wire only if turn
signals don’t work)
[4] Clutch Output: Dk.Blue: 7
63
733716
17
1
A Plug (Black)
at VESCM
(-) Trunk Release Output: Red/White: 9
B Plug
(White)
A Plug
(Black)
VESCM - Driver side,
under dashboard
63
73
3716
171
Door Locks: Violet/Brown: 1
Door Locks: Violet/Green: 9
[4] (-) Clutch: Violet/White or
Violet/Black, pin 55
2 x 1Amp
Diodes
FT CAN High:
Orange/Green,
pin 16
(-) PTS: Violet/Green,
pin 13
FT CAN Low:
Orange/Brown,
pin 15
14
1
9
8
16
(-) PTS:
Violet/Blue, pin 4
(-) Trunk Release: Violet, pin 23
[5] (+) Brake: Black/Red, pin 43
Lock/Unlock:
Brown/Green,
pin 25
4: Yellow/Red: Key Wrap [3]
5: Orange/Red: Key Wrap [3]
3: Brown/Red: Key Wrap [3]
The Remote Start
Safety Override
Switch MUST be in
the ON position.
With the exception of the OBDII diagnostic connector, all connectors are displayed from the wire side (unless specified otherwise).
[1] The installation of an aftermarket hood pin is only required on vehicles that are not equipped with a factory hood pin.
[3] For Key Wrap instructions refer to pages 7-10.
[4] For manual transmission vehicle only.
[5] For automatic transmission vehicle only.
16 Black 3 Wh
4 White 12 White4 Red
7 White 2 Wh
2 Bk6 Green
18 White
Manual/Auto. Transmission Type Prog.
Button
Manual/Auto. Transmission Type Prog.
Button
Remote Start Safety
Override Switch
[2] The siren is only compatible with Directed Digital Hybrid Systems..

20 Directed Digital System VW02
© 2016 Directed. All rights reserved.
Type 9 - Regular Key
63
73
3716
17
1
FT CAN High: Orange/Green: 7
Door Locks: Violet/Brown: 1
Door Locks: Violet/Green: 9
FT CAN Low: Orange/Brown: 8
10: Red: (+) 12V (+) 12V
[2] (+) Siren Output: Brown: 17
9: Black: (-) Ground
Siren
(-) Ground
Hood Pin
Ignition
Switch
63
73
3716
171
(-) Trunk Release Output: Red/White: 9
(-) Hazards SW Output: Green/Black: 10
B Plug
(White)
A Plug
(Black)
1 2 5
976
10
3
8
4
(+) Starter Output: Green/Red: 14
(+) Accessory Output: White/Red: 12
2: White/Brown: (+) Ignition Output
1: White: (+) 12V
[1] (-) Hood Input: Gray: 3
VESCM - Driver side,
under dashboard
B Plug (White)
at VESCM
A Plug (Black)
at VESCM
[4] Clutch Output: Dk.Blue: 7
(-) Hazards:
Brown/Red, pin 28
(-) Trunk Release: Violet, pin 23
Lock/Unlock:
Brown/Green, pin 25
(+) Accessory: Black/Red, pin 3 (+) Starter: Red/Black, pin 4
(+) Ignition: Black/Violet, pin 8
FT CAN Low:
Orange/Brown,
pin 21
[4] (-) Clutch: Violet/White
or Violet/Black, pin 55
FT CAN High:
Orange/Green,
pin 20
4: Yellow/Red: Key Wrap
[3]
5: Orange/Red: Key Wrap [3]
3: Brown/Red: Key Wrap [3]
The Remote Start
Safety Override
Switch MUST be in
the ON position.
Remote Start Safety
Override Switch
With the exception of the OBDII diagnostic connector, all connectors are displayed from the wire side (unless specified otherwise).
[1] The installation of an aftermarket hood pin is only required on vehicles that are not equipped with a factory hood pin.
[2] The siren is only compatible with Directed Digital Hybrid Systems.
[3] For Key Wrap instructions refer to pages 7-10.
[4] For manual transmission vehicle only.
16 Black 3 Wh
4 White 12 White4 Red
7 White 2 Wh
2 Bk6 Green
18 White
Manual/Auto. Transmission Type Prog.
Button
Manual/Auto. Transmission Type Prog.
Button
30
86 85
87
87a
(+) 12V
Fuse 5A
(+) Brake:
Black/Red, pin 43
Note: Connect only on vehicle
where brake needs to be
depressed to start.