Directed Xpresskit DBALL2 User manual

Vehicle Application Guide......................................................................................................................................................................
Installation
Type 1a (with CHTHD1/THCHD1 T-Harness).....................................................................................................................................
Type 1b (without T-Harness)...............................................................................................................................................................
Parking Light Vehicle Wiring Reference Chart (Type 1)........................................................................................................................
Type 2a (with CHTHD1/THCHD1 T-Harness).....................................................................................................................................
Type 2b (without T-Harness)...............................................................................................................................................................
Vehicle Wiring Reference Chart (Type 2).............................................................................................................................................
Type 3a (with CHTHD2/THCHD2 T-Harness R9)...............................................................................................................................
Type 3b (with CHTHD2/THCHD2 T-Harness R1-R6)..........................................................................................................................
Type 3c (without T-Harness)................................................................................................................................................................
Vehicle Wiring Reference Chart (Type 3)..............................................................................................................................................
Type 4 (not compatible with T-Harness)................................................................................................................................................
Vehicle Wiring Reference Chart (Type 4)..............................................................................................................................................
SmartStart/XL202 Installation Notes.....................................................................................................................................................
Programming
Module Programming for Installation (with Factory Keyless)...............................................................................................................
Module Programming for Installation (without Factory Keyless)..........................................................................................................
Module Reset........................................................................................................................................................................................
Hard Reset............................................................................................................................................................................................
Feature & Option List............................................................................................................................................................................
Feature Programming...........................................................................................................................................................................
LED Diagnostics & Troubleshooting.....................................................................................................................................................
Parking Light Error Codes....................................................................................................................................................
Limited One-Year Consumer Warranty..................................................................................................................................................
Quick Reference Guide.........................................................................................................................................................................
02
03
04
05
06
07
08
09
10
11
12
14
15
16
17
19
20
20
21
22
23
24
25
26
Index
Platform: DBALL2
Firmware: CHRYSLER Remote Start Ready (RSR) Installation
© 2016 Directed. All rights reserved.
Rev.: 20160908
® Chrysler, Dodge, Jeep and Volkswagen are registered trademarks and property of their respective companies.
Installation Guide
Update Alert: Firmware updates are posted on the web on a regular basis. We recommend
that you check for firmware and/or install guide updates prior to installing this product.
Important!
This product is NOT compatible with vehicles equipped with a manual transmission.
Remote Start Ready (RSR) is a function that enables the interface module to remote start the vehicle
completely on its own. Consequently, there is no need for an aftermarket or an OEM remote starter in order to
start the vehicle from a distance.
SmartStart Compatible
SmartStart is equipped with D2D, which means it can be connected to an interface module and used in Remote
Start Ready (RSR) mode without the use of a remote starter. See the Module Programming section for more
information.
The CHRYSLER firmware for DBALL2 is an all-in-one door lock and override module compatible with
specific Chrysler, Dodge, Jeep and Volkswagen vehicles. This guide supports the installation of a
DBALL2 in Remote Start Ready (RSR) mode with or without a Plug & Play (CHTHD1/THCHD1 or
CHTHD2/THCHD2)
T-Harness (optional). This solution offers three (3) configuration options to control your system: 3x
OEM Lock Remote Start Activation, RF System or SmartStart (all sold separately).
This module can only be flashed and configured using DirectLink at www.directechs.com or using
the Directechs Mobile application for smartphones. Refer to the Module Programming section on
pages 17-19 for more information.
This guide supports the installation of a DBALL in Remote Start Ready (RSR) mode with or without a
Plug & Play (CHTHD1 or CHTHD2) T-Harness (Optional). This solution offers three (3) configuration
options to control your system: 3x OEM Lock Remote Start Activation, RF Kit or SmartStart
(all sold separately).

Platform: DBALL2
Firmware: CHRYSLER Remote Start Ready (RSR) Installation
© 2016 Directed. All rights reserved.
Rev.: 20160908
Vehicle Application Guide Page 2
* To select the proper installation between
types 3 and 4, locate the ignition switch
connector and select your install type as
illustrated below:
Connector side view
at ignition switch
Type 3 vehicles do not have
a (+) Starter wire at the ignition switch.
Type 4 vehicles have a (+) Starter wire
at pin 4 of the ignition switch.
Connector side view
at ignition switch
(+) Starter, pin 4
1
5 or 6
1
5 or 6
The following table lists the vehicles and features which are compatible with this product. The number assigned to each
year allows you to determine which installation type should be used for your vehicle.
Legend:
PK: Transponder & Immobilizer Override
AV: Horn & Lights Controls
CC: Comfort & Convenience Controls
DL: OE Door Lock & Alarm Control
RS: Remote Start & Engine Controls
SS: Integrated Security & Monitoring
ST: Function/Feature Status
Vehicles
2016 2015 2014 2013 2012 2011 2010 2009 2008 2007 2006 2005 2004 PK-Immobilizer Bypass-Data No Key Req'd AV-Parking Lights Control CC-Heated Seats Activation DL-Arm Factory Security DL-Disarm Factory Security DL-Door Lock Control DL-Door Unlock DL-Driver Priority Unlock DL-Sliding Door Control Driver DL-Sliding Door Control Passenger DL-Trunk / Hatch Release RS-3x LOCK START (Start control using OEM Remote) RS-3x LOCK STOP (Stop control using OEM Remote) RS-RAP Shut Down (Retained ACC Power) RS-Remote Start Ready RS-SmartStart RS-Tach / RPM Output SS-Entry Monitoring ALL Door Pins SS-Entry Monitoring Driver Door Pin SS-Entry Monitoring Trunk/Hatch Pin ST-Brake Status (foot brake)
Chrysler
200 3 3 3 3 • • • • • • • • • • • • • • • • •
300/300c 2 2 2 • • • • • • • • • • • • • • • • • •
300/300c 4 4 4 • • • • • • • • • • • • • • • • • •
Aspen 3 3 3 • • • • • • • • • • • • • • • • •
PT Cruiser 4 4 4 4 4 • • • • • • • • • • • • • • • •
Sebring 3 3 3 3 • • • • • • • • • • • • • • • • •
Sebring Convertible 3 3 3 • • • • • • • • • • • • • • • • •
Sebring Sedan 3 3 3 3 • • • • • • • • • • • • • • • • •
Town & Country 1 1 1 1 1 1 1 1 1 • • • • • • • • • • • • • • • • • • • •
Dodge/Ram
1500 1 1 • • • • • • • • • • • • • • • •
2500 1 1 • • • • • • • • • • • • • • • •
3500 1 1 • • • • • • • • • • • • • • • •
Avenger 3 3 3 3 3 3 3 • • • • • • • • • • • • • • • • •
C/V 1 1 1 1 1 • • • • • • • • • • • • • • • • • • • •
Caliber 3 3 3 3 3 3 or 4* • • • • • • • • • • • • • • • •
Caravan 1 1 1 • • • • • • • • • • • • • • • • • • • •
Challenger 1 1 1 1 1 1 1 • • • • • • • • • • • • • • • • • •
Challenger (Smart Key) 1 1 1 1 1 1 1 • • • • • • • • • • • • • • • • • •
Charger 2 2 2 • • • • • • • • • • • • • • • • • •
Charger 4 4 • • • • • • • • • • • • • • • • • •
Dakota 3 3 3 3 3 • • • • • • • • • • • • • • •
Dakota 5 5 • • • • • • • • • • • •
Durango 1 1 1 • • • • • • • • • • • • • • • • •
Durango 3 3 3 • • • • • • • • • • • • • • • •
Grand Caravan 1 1 1 1 1 1 1 1 1 • • • • • • • • • • • • • • • • • • • •
Journey 1 1 • • • • • • • • • • • • • • • •
Magnum 2 • • • • • • • • • • • • • • • • •
Magnum 4 4 4 • • • • • • • • • • • • • • • • • •
Nitro 3 3 3 3 3 • • • • • • • • • • • • • • • •
RAM 1 1 • • • • • • • • • • • • • • • •
RAM 3 or 4* 3 or 4* 3 or 4* • • • • • • • • • • • • • • •
Jeep
Commander 2 2 2 4 4 • • • • • • • • • • • • • • • • •
Compass 3 3 3 3 3 3 3 3 3 3 • • • • • • • • • • • • • • • •
Grand Cherokee 1 1 1 • • • • • • • • • • • • • • • • •
Grand Cherokee 2 2 2 • • • • • • • • • • • • • • • •
Grand Cherokee 4 4 4 • • • • • • • • • • • • • • • • •
Grand Cherokee (Smart
Key) 111 • • • • • • • • • • • • • • • • •
Liberty 3 3 3 3 3 • • • • • • • • • • • • • • • •
Patriot 3 3 3 3 3 3 3 3 3 3 • • • • • • • • • • • • • • • •
Wrangler 3 3 3 3 3 3 3 3 3 3 • • • • • • • • • • • • • • • •
Mitsubishi
Raider 3 3 3 • • • • • • • • • • • • • • •
Volkswagen
Routan 1 1 1 1 1 • • • • • • • • • • • • • • • • • • • •
This guide supports the installation of a DBALL in Remote Start Ready (RSR) mode with or without a
Plug & Play (CHTHD1 or CHTHD2) T-Harness (Optional). This solution offers three (3) configuration
options to control your system: 3x OEM Lock Remote Start Activation, RF Kit or SmartStart
(all sold separately).

Platform: DBALL2
Firmware: CHRYSLER Remote Start Ready (RSR) Installation
© 2016 Directed. All rights reserved.
Rev.: 20160908
Installation Type 1a (with CHTHD1/THCHD1 T-Harness)
Page 3
Important!
The Hood Pin and Remote Start Safety Override Switch are mandatory safety devices, but are NOT supplied with the DBALL.
30
86 85
87
87a
10
DBALL2
RF
Prog. Button
LED
4
14 12 2
OR
RAP Off: Yellow/Black: 10
[1] Parking Light MUX Output: Violet/Green: 8
[1] Parking Light MUX Output: Violet/Brown: 9
[1] (-) Parking Lights via Relay: Green/Black: 2
(-) Driver Door Trigger
Violet wire in
driver kick panel
See page 5 for
wiring information
TX
(-) Ground
RX
(+) 12V
To vehicle’s
(+) Parking Lights
White/Violet
Fuse 15A
+12V
ONLY connect for
Dodge Journey.
6: White/Black: (-) Hood
Hood Pin
Remote Start Safety
Override Switch
Ignition
Barrel
(vehicle side)
12-pin Connector
(Vehicle side)
12-pin Connector
(harness side)
12-pin Connector
(harness side)
You can connect to either a XL202
RFTD OR a SmartStart module.
Refer to the SmartStart/XL202
Installation Notes for more information.
CHTHD1/
THCHD1
(optional)
With the exception of the OBDII Diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise).
[1] See Parking Lights wiring reference chart for the appropriate Parking Lights configuration.
Wires not listed in this diagram are not required for the installation.
This guide supports the installation of a DBALL in Remote Start Ready (RSR) mode with or without a
Plug & Play (CHTHD1 or CHTHD2) T-Harness (Optional). This solution offers three (3) configuration
options to control your system: 3x OEM Lock Remote Start Activation, RF Kit or SmartStart
(all sold separately).

Platform: DBALL2
Firmware: CHRYSLER Remote Start Ready (RSR) Installation
© 2016 Directed. All rights reserved.
Rev.: 20160908
Installation Type 1b (without T-Harness) Page 4
Important!
The Hood Pin and Remote Start Safety Override Switch are mandatory safety devices, but are NOT supplied with the DBALL.
10
DBALL2
RF
Prog. Button
LED
4
14 12 2
RAP Off: Yellow/Black: 10
[1] Parking Lights MUX Output: Violet/Green: 8
[1] Parking Lights MUX Output: Violet/Brown: 9
(-) Driver door Trigger
Violet wire in
driver kick panel
TX
(-) Ground
RX
(+) 12V
Ignition
Barrel
1
6
12 7
Connector side view
at ignition switch
[1] (-) Parking Lights via Relay: Green/Black: 2
HS CAN High: Tan/Black: 3
HS CAN Low: Tan: 4
Ignition Isolation (veh. side): Yellow: 8
Ignition Isolation (conn. side): Orange/Yellow: 9
(+) 12V: Brown: 7
(-) Ground: Black: 14
(+) 12V: Red: 13
6: White/Black: (-) Hood
Hood Pin
Remote Start Safety
Override Switch
You can connect to either a XL202
RFTD OR a SmartStart module.
Refer to the SmartStart/XL202
Installation Notes for more information.
With the exception of the OBDII Diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise).
[1] See Parking Lights wiring reference chart for the appropriate Parking Lights configuration.
(+) Ignition: Pink/White, pin 3
(+) 12V:Lt.Blue/Red ,pin 1
(-) Ground: Black/Striped, pin 4
HS CAN High: pin 5
HS CAN Low: pin 6
See page 5 for
wiring information
OR
30
86 85
87
87a
To vehicle’s
(+) Parking Lights
White/Violet
Fuse 15A
+12V
ONLY connect for
Dodge Journey.
This guide supports the installation of a DBALL in Remote Start Ready (RSR) mode with or without a
Plug & Play (CHTHD1 or CHTHD2) T-Harness (Optional). This solution offers three (3) configuration
options to control your system: 3x OEM Lock Remote Start Activation, RF Kit or SmartStart
(all sold separately).

Platform: DBALL2
Firmware: CHRYSLER Remote Start Ready (RSR) Installation
© 2016 Directed. All rights reserved.
Rev.: 20160908
Type 1 - Parking Light Vehicle Wiring Reference Chart
Page 5
6
5
4
3
2
1
54
9 8 7
32
10 6
1
Light switch,
black 10-pin plug
Light switch,
black 6-pin plug
Vehicle Years Vehicle Wire Location on vehicle Polarity
DBALL Output from
12 Pin connector
Chrysler
Town & Country 2011+ White/Green Black connector at light switch, pin 3 MUX 8: Violet/Green: Parking Light MUX
9: Violet/Brown: Parking Light MUX
Town & Country 2008-10 White/Brown Black connector at light switch, pin 1 MUX 8: Violet/Green: Parking Light MUX
9: Violet/Brown: Parking Light MUX
Dodge/Ram
1500 2011+ White Black connector at light switch, pin 1 MUX 8: Violet/Green: Parking Light MUX
9: Violet/Brown: Parking Light MUX
2500 2011+ White Black connector at light switch, pin 1 MUX 8: Violet/Green: Parking Light MUX
9: Violet/Brown: Parking Light MUX
3500 2011+ White Black connector at light switch, pin 1 MUX 8: Violet/Green: Parking Light MUX
9: Violet/Brown: Parking Light MUX
C/V 2011+ White/ Lt.Green Black connector at light switch, pin 3 MUX 8: Violet/Green: Parking Light MUX
9: Violet/Brown: Parking Light MUX
Caravan 2008-10 White/Brown Black connector at light switch, pin 1 MUX 8: Violet/Green: Parking Light MUX
9: Violet/Brown: Parking Light MUX
Challenger 2008+ White/Brown Black connector at light switch, pin 1 MUX 8: Violet/Green: Parking Light MUX
9: Violet/Brown: Parking Light MUX
Challenger (Smart Key) 2008+ White/Brown Black connector at light switch, pin 1 MUX 8: Violet/Green: Parking Light MUX
9: Violet/Brown: Parking Light MUX
Durango 2011+ White/Green Black connector at light switch, pin 3 MUX 8: Violet/Green: Parking Light MUX
9: Violet/Brown: Parking Light MUX
Grand Caravan 2011+ White/Green Black connector at light switch, pin 3 MUX 8: Violet/Green: Parking Light MUX
9: Violet/Brown: Parking Light MUX
Grand Caravan 2008-10 White/Brown Black connector at light switch, pin 1 MUX 8: Violet/Green: Parking Light MUX
9: Violet/Brown: Parking Light MUX
Journey 2009-10 WhiteViolet Passenger kick panel (+) 2: Green/Black: to relay for (+)
parking lights
RAM 2009-10 White Black connector at light switch, pin 1 MUX 8: Violet/Green: Parking Light MUX
9: Violet/Brown: Parking Light MUX
Jeep
Grand Cherokee 2011+ White/Green Black connector at light switch, pin 1 MUX 8: Violet/Green: Parking Light MUX
9: Violet/Brown: Parking Light MUX
Grand Cherokee
(Smart Key) 2011+ White/Green Black connector at light switch, pin 1 MUX 8: Violet/Green: Parking Light MUX
9: Violet/Brown: Parking Light MUX
Volkswagen
Routan 2011+ White/Green Black connector at light switch, pin 3 MUX 8: Violet/Green: Parking Light MUX
9: Violet/Brown: Parking Light MUX
Routan 2009-10 White/Brown Black connector at light switch, pin 1 MUX 8: Violet/Green: Parking Light MUX
9: Violet/Brown: Parking Light MUX
This guide supports the installation of a DBALL in Remote Start Ready (RSR) mode with or without a
Plug & Play (CHTHD1 or CHTHD2) T-Harness (Optional). This solution offers three (3) configuration
options to control your system: 3x OEM Lock Remote Start Activation, RF Kit or SmartStart
(all sold separately).

Platform: DBALL2
Firmware: CHRYSLER Remote Start Ready (RSR) Installation
© 2016 Directed. All rights reserved.
Rev.: 20160908
Installation Type 2a (with CHTHD1/THCHD1 T-Harness)
Page 6
Important!
The Hood Pin and Remote Start Safety Override Switch are mandatory safety devices, but are NOT supplied with the DBALL.
10
DBALL2
Prog. Button
LED
4
14 12 2
Twisted pair in the steering column or behind radio
White/Orange
White/Gray, White,
White/Pink or White/Black
RF
FT CAN High: Orange/Green: 5
FT CAN Low: Orange/Brown: 6
[1] (-) Parking Lights: Green/Black: 2
(-) Driver Door Trigger
Violet wire in
driver kick panel or
driver door (Jeeps ONLY)
RAP Off: Yellow/Black: 10
[1] Parking Light MUX Output: Violet/Green: 8
[1] Parking Light MUX Output: Violet/Brown: 9
See page 8 for
wiring information
TX
(-) Ground
RX
(+) 12V
OR
6: White/Black: (-) Hood
Hood Pin
Remote Start Safety
Override Switch
CHTHD1/
THCHD1
(optional)
12-pin Connector
(Vehicle side)
Ignition
Barrel
(vehicle side)
12-pin Connector
(harness side)
12-pin Connector
(harness side)
You can connect to either a XL202
RFTD OR a SmartStart module.
Refer to the SmartStart/XL202
Installation Notes for more information.
With the exception of the OBDII Diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise).
[1] See Parking Lights wiring reference chart for the appropriate Parking Lights configuration.
Wires not listed in this diagram are not required for the installation.
This guide supports the installation of a DBALL in Remote Start Ready (RSR) mode with or without a
Plug & Play (CHTHD1 or CHTHD2) T-Harness (Optional). This solution offers three (3) configuration
options to control your system: 3x OEM Lock Remote Start Activation, RF Kit or SmartStart
(all sold separately).

Platform: DBALL2
Firmware: CHRYSLER Remote Start Ready (RSR) Installation
© 2016 Directed. All rights reserved.
Rev.: 20160908
Installation Type 2b (without T-Harness) Page 7
Important!
The Hood Pin and Remote Start Safety Override Switch are mandatory safety devices, but are NOT supplied with the DBALL.
[1] See Parking Lights wiring reference chart for the appropriate Parking Lights configuration.
Ignition
Barrel
See page 8 for
wiring information
OR
HS CAN High:White/Black or White/Lt. Green, pin 5
HS CAN Low: White/Lt. Blue, pin 6
1
6
12 7
RAP Off: Yellow/Black: 10
[1] Parking Light Out.: Violet/Green: 8
[1] Parking Light Out.: Violet/Brown: 9
(-) Driver Door Trigger
Violet wire in
driver kick panel
or
driver door(Jeeps ONLY)
[1] (-) Parking Lights: Green/Black: 2
HS CAN High: Tan/Black: 3
HS CAN Low: Tan: 4
(+) 12V: Brown: 7
(-) Ground: Black: 14
(+) 12V: Red: 13
10
DBALL2
Prog. Button
LED
4
14 12 2
Twisted pair in the steering column or behind radio
White/Orange
White/Gray, White
or White/Pink
RF
TX
(-) Ground
RX
(+) 12V
6: White/Black: (-) Hood
Hood Pin
Ignition Switch
(connector side view)
(+) Ignition Car Side: Yellow: 8
(+) Ignition Key Side: Orange/Yellow: 9
Remote Start Safety
Override Switch
FT CAN High: Orange/Green: 5
FT CAN Low: Orange/Brown: 6
You can connect to either a XL202
RFTD OR a SmartStart module.
Refer to the SmartStart/XL202
Installation Notes for more information.
With the exception of the OBDII Diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise).
(+) Ignition: Pink/White, pin 3
(+) 12V:Lt.Blue/Red, pin 1
(-) Ground: Black/Striped, pin 4
This guide supports the installation of a DBALL in Remote Start Ready (RSR) mode with or without a
Plug & Play (CHTHD1 or CHTHD2) T-Harness (Optional). This solution offers three (3) configuration
options to control your system: 3x OEM Lock Remote Start Activation, RF Kit or SmartStart
(all sold separately).

Platform: DBALL2
Firmware: CHRYSLER Remote Start Ready (RSR) Installation
© 2016 Directed. All rights reserved.
Rev.: 20160908
Page 8
Type 2 - Parking Light Vehicle Wiring Reference Chart
Jeep Commander & Jeep
Grand Cherokee
ALTERNATIVE parking light
connection
Refer to DirectWire for additional parking light locations.
Light switch,
black 10-pin plug
7
2
6
1
10
5
9
4
8
3
Vehicle Years Vehicle Wire Location on vehicle (+) / (-)
DBALL Output from
12 Pin connector
Chrysler
300/300c 2008-10 White/Brown Black connector at light switch, pin 1 MUX 8: Violet/Green: Parking Light MUX
9: Violet/Brown: Parking Light MUX
Dodge
Charger 2008-10 White/Brown Black connector at light switch, pin 1 MUX 8: Violet/Green: Parking Light MUX
9: Violet/Brown: Parking Light MUX
Magnum 2008 White/Brown Black connector at light switch, pin 1 MUX 8: Violet/Green: Parking Light MUX
9: Violet/Brown: Parking Light MUX
Jeep
Commander 2008-10 White/Dk. Blue Hazard light switch (-) (-) Parking Lights Output
Grand Cherokee 2008-10 White/Dk. Blue Hazard light switch (-) (-) Parking Lights Output
This guide supports the installation of a DBALL in Remote Start Ready (RSR) mode with or without a
Plug & Play (CHTHD1 or CHTHD2) T-Harness (Optional). This solution offers three (3) configuration
options to control your system: 3x OEM Lock Remote Start Activation, RF Kit or SmartStart
(all sold separately).

Platform: DBALL2
Firmware: CHRYSLER Remote Start Ready (RSR) Installation
© 2016 Directed. All rights reserved.
Rev.: 20160908
Installation Type 3a (with CHTHD2/THCHD2 T-Harness R9-R10)
Page 9
Important!
The Hood Pin and Remote Start Safety Override Switch are mandatory safety devices, but are NOT supplied with the DBALL.
TX
(-) Ground
RX
(+) 12V
10
DBALL2
Prog. Button
LED
4
14 12 2
RAP Off: Yellow/Black: 10
(-) Parking Lights: Green/Black: 2
RF
30
86 85
87
87a
To vehicle’s
(+) Parking Lights
Fuse 15A
+12V
See page 12 for
wiring information
You can connect to either a XL202
RFTD OR a SmartStart module.
Refer to the SmartStart/XL202
Installation Notes for more information.
N.C.
8-pin Connector
at ignition switch
(Vehicle side)
8-pin Connector
(harness side)
8-pin Connector
(harness side)
Ignition Switch
(Vehicle side)
CHTHD2/
THCHD2 R9-R10
(optional)
T-04
Remote Start Safety
Override Switch
Hood Pin
White/Black
HS CAN High: Orange/Green: 5
HS CAN Low: Orange/Brown: 6
With the exception of the OBDII Diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise).
Use this connection ONLY
with DBALL2.
However, it must NOT be
used in the Nitro, Liberty,
Wrangler & Wrangler
Limited.
Diagnostic Connector OBDII
(connector side view)
1 8
169
(-) Driver Door Trigger
Violet wire in
driver kick panel
Wires not listed in this diagram are not required for the installation.
HS CAN High: pin 6
HS CAN Low: pin 14
This guide supports the installation of a DBALL in Remote Start Ready (RSR) mode with or without a
Plug & Play (CHTHD1 or CHTHD2) T-Harness (Optional). This solution offers three (3) configuration
options to control your system: 3x OEM Lock Remote Start Activation, RF Kit or SmartStart
(all sold separately).

Platform: DBALL2
Firmware: CHRYSLER Remote Start Ready (RSR) Installation
© 2016 Directed. All rights reserved.
Rev.: 20160908
Installation Type 3b (with CHTHD2/THCHD2 T-Harness R1-R6)
Page 10
Important!
The Hood Pin and Remote Start Safety Override Switch are mandatory safety devices, but are NOT supplied with the DBALL.
Also note that this installation is NOT compatible with DBALL2.
10
DBALL2
Prog. Button
LED
4
14 12 2
RAP Off: Yellow/Black: 10
RF
(-) Driver Door Trigger
Violet wire in
driver kick panel TX
(-) Ground
RX
(+) 12V
(-) Parking Lights: Green/Black: 2
30
86 85
87
87a
To vehicle’s
(+) Parking Lights
Fuse 15A
+12V
See page 12 for
wiring information
6: White/Black: (-) Hood
Hood Pin
Remote Start Safety
Override Switch
You can connect to either a XL202
RFTD OR a SmartStart module.
Refer to the SmartStart/XL202
Installation Notes for more information.
8-pin Connector
at ignition switch
(Vehicle side)
Ignition Switch
(Vehicle side) CHTHD2/
THCHD2 R1-R6
(optional)
8-pin Connector
(harness side)
8-pin Connector
(harness side)
With the exception of the OBDII Diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise).
Wires not listed in this diagram are not required for the installation.
This guide supports the installation of a DBALL in Remote Start Ready (RSR) mode with or without a
Plug & Play (CHTHD1 or CHTHD2) T-Harness (Optional). This solution offers three (3) configuration
options to control your system: 3x OEM Lock Remote Start Activation, RF Kit or SmartStart
(all sold separately).

Platform: DBALL2
Firmware: CHRYSLER Remote Start Ready (RSR) Installation
© 2016 Directed. All rights reserved.
Rev.: 20160908
Installation Type 3c (without T-Harness) Page 11
Important!
The Hood Pin and Remote Start Safety Override Switch are mandatory safety devices, but are NOT supplied with the DBALL.
With the exception of the OBDII Diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise).
10
DBALL2
Prog. Button
LED
4
14 12 2
FT CAN High: Tan/Black: 3
(+) Ignition: Yellow: 8
FT CAN Low: Tan: 4
RF
(-) Driver Door Trigger
Violet wire in
driver kick panel
TX
(-) Ground
RX
(+) 12V
FT CAN Low: pin 7
FT CAN High: pin 6
1 8
Connector
at Sentry Key Module
near Ignition Switch
(-) Ground: Black: 14
(+) 12V: Red: 13
Multiplex Output: Violet/Green: 8
Multiplex Output: Violet/Brown: 9
RAP Off: Yellow/Black: 10
(-) Parking Lights: Green/Black: 2
(+) 12V: Brown: 7
30
86 85
87
87a
To vehicle’s
(+) Parking Lights
Fuse 15A
+12V
(+) Ignition:Pink or
Pink/Striped, pin 3
MUX: Violet/Brown, pin 1
See page 12 for
wiring information
6: White/Black: (-) Hood
Hood Pin
(+) 12V: Red or
Red/Striped,pin 5
(-) Ground: Black or
Black/Striped, pin 4
Remote Start Safety
Override Switch
You can connect to either a XL202
RFTD OR a SmartStart module.
Refer to the SmartStart/XL202
Installation Notes for more information.
HS CAN High: Orange/Green: 5
HS CAN Low: Orange/Brown: 6
Use this connection ONLY
with DBALL2.
However, it must NOT be
used in the Nitro, Liberty,
Wrangler & Wrangler
Limited.
Diagnostic Connector OBDII
(connector side view)
1 8
169
HS CAN High: pin 6
HS CAN Low: pin 14
Refer to the Vehicle
Wiring Reference
Charts on page 13
for CAN wire colors
and location.
This guide supports the installation of a DBALL in Remote Start Ready (RSR) mode with or without a
Plug & Play (CHTHD1 or CHTHD2) T-Harness (Optional). This solution offers three (3) configuration
options to control your system: 3x OEM Lock Remote Start Activation, RF Kit or SmartStart
(all sold separately).

Platform: DBALL2
Firmware: CHRYSLER Remote Start Ready (RSR) Installation
© 2016 Directed. All rights reserved.
Rev.: 20160908
Type 3 - Parking Light Vehicle Wiring Reference Chart Page 12
46
55
65
20
10
3
29
58
59
61
72
64
17
16
15
14
11
60
17 38 44
31 37 68 74
Above driver kick,
gray 74-pin plug
Underhood fuse box,
black 20-pin plug
10
20
9
19
8
18
7
17
6
16
5
15
4
14
3
13
2
12
1
11
39 25
28
29
32
33 21
36 24
9
12
13
16
820
5
17
1
38 4
37 3
40 2
Driver kick fuse box,
black 40-pin plug
Vehicle Years Wire Polarity Location
Chrysler
200 2011-14 White/Violet (+) Driver kick panel
Aspen 2007-09 Pink/Red (+) Driver kick fuse box, black 40-pin plug, pin 6
Sebring 2007-10 White/Violet (+) Driver kick panel
Sebring Convertible 2008-10 White/Violet (+) Driver kick panel
Sebring Sedan 2007-10 White/Violet (+) Driver kick panel
Dodge
Avenger 2008+ White/Violet (+) Driver kick panel
Caliber 2007-12 White/Violet (+) Driver kick panel
Dakota 2007-11 Pink/Red (+) Underhood fuse box, black 20-pin plug, pin 15
Durango 2007-09 Pink/Red (+) Driver kick fuse box, black 40-pin plug, pin 6
Nitro 2007-11 White/Violet (+) Driver kick panel
White/Yellow (L),
White/Gray (+)
Totally Integrated Power Module under hood,
connector C9 pin 8,10
Use (2) 6Amp diodes to isolate left and right
parking lights.
OR
White/Lt.Green MUX
Headlight switch.
Use a resitor and relay, see Tech Tip 1082
Multiplex Light Circuit Integration.
Jeep
Compass 2007+ White/Violet (+) Driver kick panel
Liberty 2008-12 White/Violet (+) Driver kick panel
Patriot 2007+ White/Violet (+) Driver kick panel
Wrangler 2007+ White/Violet (+) Passenger kick panel
Wrangler Limited 2007+ White/Violet (+) Passenger kick panel
RAM 2006-08
Module-Totally Integrated Power C9
1
6
7
12
This guide supports the installation of a DBALL in Remote Start Ready (RSR) mode with or without a
Plug & Play (CHTHD1 or CHTHD2) T-Harness (Optional). This solution offers three (3) configuration
options to control your system: 3x OEM Lock Remote Start Activation, RF Kit or SmartStart
(all sold separately).

Platform: DBALL2
Firmware: CHRYSLER Remote Start Ready (RSR) Installation
© 2016 Directed. All rights reserved.
Rev.: 20160908
Type 3 - CAN Vehicle Wiring Reference Chart Page 13
Vehicle Years FT CAN High FT CAN Low
200 2011-14 White/Orange White
Aspen 2007-09 White/Orange White
Sebring 2007-10 White/Orange White
Sebring Convertible 2007-10 White/Orange White
Sebring Sedan 2007-10 White/Orange White
Avenger 2008-14 White/Orange White
Caliber 2007-12 White/Orange White/Pink
Dakota 2007-11 White/Orange White
Durango 2007-09 White/Orange White
Nitro 2007-11
White/Black or
White/Lt.Green White/Lt.Blue
RAM 2006-08 White/Orange White
Compass 2007-16 White/Orange White/Pink
Liberty 2008-12 White/Black White/Lt.Blue
Patriot 2007-16 White/Orange White/Pink
Wrangler 2007-16 White/Black White/Lt.Blue
Raider 2007-09 White/Orange White
Mitsubishi
Dodge/Ram
Chrysler
Jeep
This guide supports the installation of a DBALL in Remote Start Ready (RSR) mode with or without a
Plug & Play (CHTHD1 or CHTHD2) T-Harness (Optional). This solution offers three (3) configuration
options to control your system: 3x OEM Lock Remote Start Activation, RF Kit or SmartStart
(all sold separately).

Platform: DBALL2
Firmware: CHRYSLER Remote Start Ready (RSR) Installation
© 2016 Directed. All rights reserved.
Rev.: 20160908
Installation Type 4 Page 14
Important!
The Hood Pin and Remote Start Safety Override Switch are mandatory safety devices, but are NOT supplied with the DBALL.
With the exception of the OBDII Diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise).
10
DBALL2
Prog. Button
LED
4
14 12 2
FT CAN High: Tan/Black: 3
FT CAN Low:White
or White/Pink ,
pin 7
FT CAN High:
White/Orange,
pin 6
1 8
(+) Ignition: pin 3
(+) Start: pin 4
MUX:
Violet/Brown,pin 2
1
Ignition Switch
(connector side view)
Sentry Key Module
near Ignition Switch
(connector side view)
RF
FT CAN Low: Tan: 4
(-) Ground: Black: 14
(+) 12V: Red: 13
(+) Ignition: Yellow: 8
(+) Start: Yellow/Red: 11
Multiplex Output: Violet/Green: 8
Multiplex Output: Violet/Brown: 9
(-) Parking Lights: Green/Black: 2
(+) 12V: Brown: 7
(+) 12V: Brown/Red: 12
(+) Parking Lights
See page 15 for
wiring information.
30
86 85
87
87a
To vehicle’s
(+) Parking Lights
Fuse 15A
+12V
5-pin
or
6-pin
6: White/Black: (-) Hood
Hood Pin
(+) 12V: Red or
Red/Striped, pin 5
(-) Ground:
Black or
Black/Striped,
pin 4
Remote Start Safety
Override Switch
You can connect to either a XL202
RFTD OR a SmartStart module.
Refer to the SmartStart/XL202
Installation Notes for more information.
HS CAN High: Orange/Green: 5
HS CAN Low: Orange/Brown: 6
Use this connection
ONLY with DBALL2.
Diagnostic Connector OBDII
(connector side view)
1 8
169
HS CAN High: pin 6
HS CAN Low: pin 14
Refer to the Vehicle
Wiring Reference
Charts on page 15
for Start wire colors
and location.
This guide supports the installation of a DBALL in Remote Start Ready (RSR) mode with or without a
Plug & Play (CHTHD1 or CHTHD2) T-Harness (Optional). This solution offers three (3) configuration
options to control your system: 3x OEM Lock Remote Start Activation, RF Kit or SmartStart
(all sold separately).

Platform: DBALL2
Firmware: CHRYSLER Remote Start Ready (RSR) Installation
© 2016 Directed. All rights reserved.
Rev.: 20160908
46
55
65
20
10
3
29
58
59
61
72
64
17
16
15
14
11
60
17 38 44
31 37 68 74
Type 4 - Parking Light Vehicle Wiring Reference Chart Page 15
Above driver kick,
gray 74-pin plug
Vehicle Years Wire (+) / (-) Location
Chrysler
300/300c 2005-07 White/Violet (+) Passenger kick panel
PT Cruiser 2006-10 White/Violet (+) Driver kick panel
Dodge
Caliber 2007 White/Violet (+) Driver kick panel
Charger 2006-07 White/Violet (+) Passenger kick panel
Magnum 2005-07 White/Violet (+) Passenger kick panel
RAM 2006 White/Gray (+) Above driver kick, gray 74-pin plug, pin 19
Jeep
Commander 2006-07 White/Dk. Blue (-) Hazard light switch
Grand Cherokee 2005-07 White/Dk. Blue (-) Hazard light switch
Vehicle Years Wire Polarity Location
Chrysler
300/300c 2005-07 Pink/Dk. Green (+) At ignition switch, black 5-pin plug
PT Cruiser 2006-10 Pink/Lt.Blue (+) At Ignition harness
Dodge
Caliber 2007 Pink/Lt.Blue (+) At ignition switch, black 5-pin plug
Charger 2006-07 Pink/Dk. Green (+) At ignition switch, black 5-pin plug
Magnum 2005-07 Pink/Dk. Green (+) At ignition switch, black 5-pin plug
RAM 2006 Dk. Green/Yellow (+) At ignition harness or starter button (SRT-10)
Jeep
Commander 2006-07 Pink/Orange (+) At Ignition harness
Grand Cherokee 2005-07 Pink/Orange (+) At Ignition harness
Start - Vehicle Wiring Reference Chart (Type 4)
This guide supports the installation of a DBALL in Remote Start Ready (RSR) mode with or without a
Plug & Play (CHTHD1 or CHTHD2) T-Harness (Optional). This solution offers three (3) configuration
options to control your system: 3x OEM Lock Remote Start Activation, RF Kit or SmartStart
(all sold separately).

Platform: DBALL2
Firmware: CHRYSLER Remote Start Ready (RSR) Installation
© 2016 Directed. All rights reserved.
Rev.: 20160908
SmartStart/XL202 Installation Notes Page 16
The optional XL202 and antenna are not included and MUST be purchased separately.
Refer to the Passive Keyless Entry (PKE) Installation Guide (N2102T) for detailed wiring information.
4
4
XL202
Antenna
XOVER
SmartStart is optional and not included. It MUST be purchased separately.
SmartStart is optional and not included. It MUST be purchased separately.
Configuration Wires (Gray & White)
Connect Gray wire to (-) Ground
5 pins
D2D (4 pins, white)
4 pins
2 pins,
not used
CABLE
CABLE
The modules must be connected in a specific order. Refer to the Module Programming section for more information.
1. Use the D2D Crossover (XOVER) cable that is provided with XL202, and NOT the one in the DBALL2 package.
2. The modules must be connected in a specific order. Refer to the Module Programming section for more information.
The modules must be connected in a specific order. Refer to the Module Programming section for more information.
SmartStart Revision B
RF Kit
RF Kit & PKE Combination
Refer to the Passive Keyless Entry (PKE) Installation Guide (N2102T) for detailed wiring information.
RF Kit, PKE & SmartStart BT Combination
SmartStart Revision A
DBALL2
DBALL2
DBALL2 LED
Prog.
Button
D2D (4 pins, white)
4 pins
2 pins,
not used
OR
SmartStart
Configuration Wires (White & Brown or Blue)
Cut Brown or Blue Loop
LED
THIS SIDE UP
LED
The DBALL2 Remote Start Ready (RSR) solution offers three (3) configuration options to control your system: 3x OEM Lock
Remote Start Activation, RF Kits or SmartStart (all sold separately). This section provides specific installation information for
SmartStart and XL202.
This guide supports the installation of a DBALL in Remote Start Ready (RSR) mode with or without a
Plug & Play (CHTHD1 or CHTHD2) T-Harness (Optional). This solution offers three (3) configuration
options to control your system: 3x OEM Lock Remote Start Activation, RF Kit or SmartStart
(all sold separately).

Platform: DBALL2
Firmware: CHRYSLER Remote Start Ready (RSR) Installation
© 2016 Directed. All rights reserved.
Rev.: 20160908
Module Programming (WITH Factory Keyless) Page 17
2or
Insert the key into the ignition barrel and turn it
to the ON position.
Key Ignition Push-to-Start (PTS) Ignition
It is important to wait for the LED to start flashing
green. Refer to the LED Diagnostics section on
page 23 for troubleshooting if the LED does not
flash green within 15 seconds.
Flashes
&
Flashes
Key IN
OFF
START
ON
It is important to wait for the LED to start flashing
green. Refer to the LED Diagnostics section on
page 23 for troubleshooting if the LED does not
flash green within 15 seconds.
Press the Push-to-Start (PTS) button twice to
turn the ignition ON.
Important: Do NOT press the brake pedal.
2X ENGINE
START
STOP
PUSH
Do NOT
press the
brake pedal
Refer to the LED Diagnostics section for more information and for troubleshooting purposes.
Go to the next page to complete the module programming.
1
10-pin
D2D
st
1
12-pin
14-pin
nd
2
rd
3
&
Solid
Connect the 10-pin, 12-pin and 14-pin harnesses to
DBALL2, then wait until the LED turns ON solid red.
10-pin
D2D
XL202
10-pin
D2D
SmartStart
OR
The DBALL2 module must be disconnected from any power source before SmartStart can
be connected to it. Failing to do so could damage DBALL2.
a. To ensure that the D2D communication between SmartStart and DBALL2 works properly,
the Gray wire must be connected to a ground source (Rev B SmartStart), and the Brown or
Blue loop must be cut (Rev A SmartStart).
b. Do NOT connect the 2-pin harness (on SmartStart). Power and ground will be provided by
the DBALL2 D2D connector.
Connect SmartStart to DBALL2 using the D2D port.
SmartStart Installation
Connect XL202 to DBALL2 using the D2D port.
XL202 Installation
Important
Make all the required connections to the vehicle, as described in the wiring diagram(s) found in this guide, and double check to
ensure everything is correct prior to moving onto the next step.
Note: Before connecting either the XL202 or SmartStart module to DBALL, it is important to ensure that the proper feature and
function programming is selected using XpressVIP (version 4.5 or higher). Visit www.directechs.com to download the latest
version of the application.
Warning! To take advantage of advanced features, you must use XpressVIP 4.5 (and higher) or the Directechs Mobile app.
When the flashing operation is successful, you can proceed with the programming instructions below.
Flashing a module using your computer:
1. Connect the interface module to your computer using the
XKLoader2.
2. Go to www.directechs.com using Internet Explorer, and
select the Config for RSR button.
3. Follow the instructions to select your vehicle, installation
type, and configure your options.
4. Once you have configured the firmware options, click on the
FLASH button.
Flashing a module using your smartphone or tablet
1. Connect the interface module to your XKLoader3.
2. Launch the Directechs Mobile app on your smartphone or
tablet.
3. Select FLASH YOUR MODULE and follow the on screen
instructions.
This guide supports the installation of a DBALL in Remote Start Ready (RSR) mode with or without a
Plug & Play (CHTHD1 or CHTHD2) T-Harness (Optional). This solution offers three (3) configuration
options to control your system: 3x OEM Lock Remote Start Activation, RF Kit or SmartStart
(all sold separately).

Platform: DBALL2
Firmware: CHRYSLER Remote Start Ready (RSR) Installation
© 2016 Directed. All rights reserved.
Rev.: 20160908
3
4
Turn the key to the OFF
position and remove it
from the ignition barrel.
Press LOCK or UNLOCK on the
factory transmitter. The LED turns
ON solid green OR orange for 3 seconds
and then turns off.
or &&
or
Solid Solid Off
Key OUT
OFF
START
IGN
or Press the Push-to-Start
(PTS) button once more
to turn the ignition OFF. 1X ENGINE
START
STOP
PUSH
PANIC
Page 18
You have successfully completed the module programming sequence.
This guide supports the installation of a DBALL in Remote Start Ready (RSR) mode with or without a
Plug & Play (CHTHD1 or CHTHD2) T-Harness (Optional). This solution offers three (3) configuration
options to control your system: 3x OEM Lock Remote Start Activation, RF Kit or SmartStart
(all sold separately).

Platform: DBALL2
Firmware: CHRYSLER Remote Start Ready (RSR) Installation
© 2016 Directed. All rights reserved.
Rev.: 20160908
3Turn the key to the OFF position and remove it from the ignition barrel.
Page 19
2
Insert the key into the ignition barrel and turn it to the ON position.
It is important to wait for the LED to start flashing green.*
* Refer to the LED Diagnostics section on page 22 for troubleshooting
if the LED does not flash green within 15 seconds.
&
Flashes
Key IN
OFF
START
ON
Key OUT
OFF
START
IGN
Module Programming (WITHOUT Factory Keyless)
Off
Press & Release Solid
Solid
or
4Press and release the programming button.
The LED turns ON solid green OR orange
for 3 seconds and then turns OFF. &
&
You have successfully completed the module programming sequence.
1
10-pin
D2D
st
1
12-pin
14-pin
nd
2
rd
3
&
Solid
Connect the 10-pin, 12-pin and 14-pin harnesses to
DBALL2, then wait until the LED turns ON solid red.
Refer to the LED Diagnostics section for more information and for troubleshooting purposes.
Important
10-pin
D2D
SmartStart
OR
The DBALL module must be disconnected from any power source before SmartStart can
be connected to it. Failing to do so could damage DBALL.
a. To ensure that the D2D communication between SmartStart and DBALL works properly, the
Gray wire must be connected to a ground source (Rev B SmartStart), and the Brown or Blue
loop must be cut (Rev A SmartStart).
b. Do NOT connect the 2-pin harness (on SmartStart). Power and ground will be provided by
the DBALL D2D connector.
Connect SmartStart to DBALL using the D2D port.
SmartStart Installation
Connect XL202 to DBALL using the D2D port.
XL202 Installation
Make all the required connections to the vehicle, as described in the wiring diagram(s) found in this guide, and double check to
ensure everything is correct prior to moving onto the next step.
Note: Before connecting either the XL202 or SmartStart module to DBALL, it is important to ensure that the proper feature and
function programming is selected using XpressVIP (version 4.5 or higher). Visit www.directechs.com to download the latest
version of the application.
Warning! To take advantage of advanced features, you must use XpressVIP 4.5 (and higher) or the Directechs Mobile app.
When the flashing operation is successful, you can proceed with the programming instructions below.
Flashing a module using your computer:
1. Connect the interface module to your computer using the
XKLoader2.
2. Go to www.directechs.com using Internet Explorer, and
select the Config for RSR button.
3. Follow the instructions to select your vehicle, installation
type, and configure your options.
4. Once you have configured the firmware options, click on the
FLASH button.
Flashing a module using your smartphone or tablet
1. Connect the interface module to your XKLoader3.
2. Launch the Directechs Mobile app on your smartphone or
tablet.
3. Select FLASH YOUR MODULE and follow the on screen
instructions.
This guide supports the installation of a DBALL in Remote Start Ready (RSR) mode with or without a
Plug & Play (CHTHD1 or CHTHD2) T-Harness (Optional). This solution offers three (3) configuration
options to control your system: 3x OEM Lock Remote Start Activation, RF Kit or SmartStart
(all sold separately).

Platform: DBALL2
Firmware: CHRYSLER Remote Start Ready (RSR) Installation
© 2016 Directed. All rights reserved.
Rev.: 20160908
Page 20
1If required for your installation, connect the 10-pin & 12-pin
harnesses to the module. Press and hold the programming
button, then connect the 14-pin harness to the module.
10-pin
D2D
st
1
12-pin
14-pin
nd
2
th
4
rd
3
Warning Against Executing a Hard Reset!
A hard reset will revert the flashed firmware back to its default settings. Depending on the installation, some settings (such
as RFTD and D2D options) may have to be reconfigured. See the Feature & Option List section of this guide.
2
Solid
&
Release
3 Release the programming button. The LED turns ON solid red.
Module Reset
Hard Reset
2& &
1
Wait 3 seconds until the LED turns ON solid orange then release the
programming button. The LED turns ON solid red.
If required for your installation, connect the 10-pin & 12-pin
harnesses to the module. Press and hold the programming
button, then connect the 14-pin harness to the module.
10-pin
D2D
st
1
12-pin
14-pin
nd
2
th
4
rd
3
A module reset will only erase programming performed in the previous steps. All settings (firmware) and settings flashed
to the module using the web configuration tool will not be affected.
Solid Release Solid
Solid Flashes
&
Wait 3 seconds until the LED turns ON solid orange, and wait 10 more seconds
until the LED starts to flash orange and red.
This guide supports the installation of a DBALL in Remote Start Ready (RSR) mode with or without a
Plug & Play (CHTHD1 or CHTHD2) T-Harness (Optional). This solution offers three (3) configuration
options to control your system: 3x OEM Lock Remote Start Activation, RF Kit or SmartStart
(all sold separately).