Displays2go DRS21BK User manual

1
DRS21BK/DRS21SV/DRS21BKCP/DRS21SVCP
Digital Store Shelving Unit

2
IMAGE DESCRIPTON QTY
Square Nut (1/4-20) 16
Long MDF Screw (3/4") 12
Medium Button Head Socket
Cap Screw (10-32 x 1/2")
4
Large Button Head Socket Cap Screw
(1/4-20 x 1/2")
24
1/4-20 Fender Washer
8
Extra Large Button Head Socket
Cap Screw (1/4-20 x 1-3/4") 8
Small M4 Button Head Phillips
Cap Screw (M4-0.7 x 10mm)
4
Small Hex Key (1/8") 1
Large Hex Key (5/32") 1
Aluminum Standos (5/8" x 1") 4
N/A String 1
N/A 8’ Long 12V Power Supply 1
HARDWARE:

3
IMAGE DESCRIPTON QTY
6’ Side Pole 2
Screen Backing 1
Extrusion Top Cap 2
Printed Lens 1
Acrylic Faceplate 1
LCD Screen 1
Shelf Bracket 6
Shelf 3
Baseplate 1
COMPONENTS:

4
ASSEMBLY:
Step 1: To feed the 8' Power
Cord up the side pole, feed the
string through the 1" hole on
the side of the pole until it is
sticking out of the far end of
the tube.
Step 2: Run the string though
the hole on the baseplate
Step 4: Tie the string that is sticking out the baseplate to the
end of the 8' Power Cord. Pull up from the other end of the
string sticking out the 1" hole on the side pole until the 8'
Power Cord is now sticking out the 1" hole on the side pole.
Step 5: Untie the string from the 8' Power Cord.
Step 3: Using the Extra
Large Button Head Socket
Cap Screws and the Fender
Washers attach both side
poles to the baseplate

5
ASSEMBLY:
Step 7: Assemble the Shelf
Brackets using (2) Square Nuts
and (2) Large Button Head
Socket Cap Screws. Place the
Large Button Head Socket Cap
Screws through the holes on the
Shelf Bracket and fasten the
Square Nuts onto the screw from
the other side of the shelf
bracket
DO NOT completely tighten the
nuts down, leave enough gap so
that they can slide into the T-slot
channels on the side poles.
Step 8: Repeat Step 7 for 4 tabs
on the ABS Screen Tray.
Step 6: Attach the pole Top
Caps to the top of the side
poles using (4) Large Button
Head Socket Cap Screws.
Repeat for second extrusion

6
ASSEMBLY:
Step 9: Install the Shelf
Brackets into the T-slots on the
side poles as shown and place
at desired shelf height. Once
you have reached desired shelf
height, tighten screws so the
shelf brackets are securely
fastened to the pole.
Step 10: Repeat Step 9 for
Screen Backing.
*Be careful not to damage the
8’ 12V Power Cord while
installing the Shelf Brackets and
Screen Backing.
Step 11: Install the Shelves to
the Shelf Brackets using (4)
Long MDF Screws in the pre-
drilled holes on the underside of
each shelf. Adjust shelf
alignment as needed.

7
ASSEMBLY:
Step 12: Install the LCD Screen in the INSTALLED Screen
Backing using the VESA 100x100 mounting holes on the
rear of the LCD Screen using (4) Small M4 Button Head
Phillips Cap Screws. Be careful not to strip the threads.
Step 13: Install the (4) Aluminum Standos in the Screen
Backing using (4) Medium Button Head Socket Cap Screws.
Step 14: Then stack Printed Lens and Acrylic Faceplate and
in-stall over the LCD Screen using the removable heads of the
standos and then tighten.