DITEC PASM24W User manual

PASM24W
1
2
5
3
4
* Other use of the device outside of the permitted purpose can not be guaranteed by the manufacturer.
TECHNICAL SPECIFICATIONS
DESCRIPTION
ENGLISH
UNIDIRECTIONAL OPENING SENSOR
FOR AUTOMATIC DOORS*
1. main connector
2. wide field antenna
3. narrow field antenna
4. push buttons
5. cover
Technology:
Transmitter frequency:
Transmitter radiated power:
Transmitter power density:
Detection mode:
Min. detection speed:
Supply voltage:
Mains frequency:
Max power consumption:
Output:
Max. contact voltage:
Max. contact current:
Max. switching power:
Mounting height:
Degree of protection:
Temperature range:
Dimensions:
Tilt angles:
Material:
Weight:
Cable lenght:
Conformity:
microwave and microprocessor
24.150 GHz
< 20 dBm EIRP
< 5 mW/cm²
motion
5 cm/s
12V to 24V AC ±10%; 12V to 24V DC +30% / -10%
50 to 60 Hz
< 2 W
relay (free of potential change-over contact)
42V AC/DC
1A (resistive)
30W (DC) / 60VA (AC)
from 1.8 m to 4 m
IP54
from -20 °C to + 55 °C
120 mm (L) x 80 mm (H) x 50 mm (W)
0° to 90° vertical; -30° to +30° lateral
ABS
215 g
2.5 m
RED 2014/53/EU, RoHS 2 2011/65/EU
Specifications are subject to changes without prior notice.
Measured in specific conditions.
User’s Guide for product version 0600 and higher
See product label for serial number
This user’s guide is an informative document and can not be seen as a commitment of result.

1
2
23
1
EAGLE ONE
OPENING THE SENSOR
MOUNTING & WIRING
Before fixing After fixing
TIPS
Apply the mounting template.
Drill 1 hole for the cable and
pull it through.
Drill 2 holes for the screws.
Position the
cable as indicated.
Fix the sensor firmly.
Avoid proximity to neon
lamps or moving objects.
Do not cover the sensor.Avoid vibrations.Do not touch electronical
parts.
APPLICATIONS
Connect the wires accordingly:
1 - BROWN - POWER SUPPLY
2 - GREEN - POWER SUPPLY
3 - WHITE - COM
4 - YELLOW - NO
5 - YELLOW - NC
Wall mounting above sliding or
revolving door Ceiling mounting in front of door
(sliding, revolving or swing doors)
Mounting on door axis (swing doors)
or

3
4
NC
NO
XXS XS S > > > > L XL XXL
1 2
> > > >>
... S, XS, XXS ... L, XL, XXL
< 3 m > 3 m
EAGLE ONE
+
MECHANICAL ADJUSTMENTS
SETTINGS (by remote control or push buttons)
FIELD SIZE
FIELD SIZE
IMMUNITY FILTER
DETECTION MODE
OUTPUT
CONFIGURATION
bi = two-way detection; uni = one-way detection towards sensor
A = active output (NO-contact)
P = passive output (NC-contact)
bi uni uni
PRM
FACTORY VALUES
low normal
Adjust the lateral antenna
angle.
Adjust the vertical antenna
angle.
OR
RESETTING TO FACTORY VALUES:
4 m x 2 m (wide) 2 m x 2.5 m (narrow)
WIDTHANGLE
uni
AWAY
PRM &
AWAY uni PRM = one-way detection also of people with reduced mobility
uni AWAY = one-way detection away from sensor
HOLD-OPEN TIME
MOUNTING
HEIGHT
DOOR CONTROL
0.5 s 1 s 2 s 3 s 4 s 5 s 6 s 7 s 8 s 9 s
< 3 m > 3 m
auto open closed open = the sensor detects constantly. The LED is ON.
closed = the sensor is in standby and does not detect. The LED is OFF.
2.2 m 2.2 m
high
> 2 seconds
2.2 m
2.2 m
highest

1
1
2
3
4
5
1
2
1
1
1
1
2
2
1
3
3
1
2
1
ASSA ABLOY Entrance Systems AB - Lodjursgatan 10 - SE-261 44 Landskrona - Sweden - www.ditecautomations.com
©ASSA ABLOY Entrance Systems AB I | Original instructions | 47.0473 / V1 - 05.21
TROUBLESHOOTING
The door remains
closed.
The LED is OFF.
The sensor power is off. Check the wiring and the power supply.
The door does not
react as expected.
The door opens
and closes
constantly.
The LED
flashes quickly
after unlocking.
The sensor does
not respond to the
remote control.
Improper output
configuration on the sensor.
The sensor is disturbed
by the door motion or
vibrations caused by the
door motion.
The sensor needs an access
code to unlock.
Batteries in the remote
control are weak or
installed improperly.
The door opens for
no apparent reason.
It rains and the sensor
detects the motion of the
rain drops.
Remote control badly
pointed.
Change the output configuration setting on
each sensor connected to the door operator.
Make sure the sensor is fixed properly.
Make sure the detection mode is unidirectional.
Increase the antenna angle.
Increase the immunity filter.
Reduce the field size.
Change the antenna angle.
Decrease the field size.
Increase the immunity filter.
Enter the right access code.
If you forgot the code, cut and restore the power
supply to access the sensor without access code.
Change or delete the access code.
Check and change the batteries if necessary.
Point the remote control towards the sensor.
Make sure the detection mode is unidirectional.
Increase the immunity filter.
In highly reflective
environments, the sensor
detects objects outside of its
detection field.
ACCESS CODE
The access code (1 to 4 digits) is recommended to set sensors installed close to each other.
SAVING AN ACCESS CODE:
DELETING AN ACCESS CODE:
In airlock vestibules,
the sensor detects the
movement of
the opposite door.
Change the antenna angle.
Change the antenna.
Increase the immunity filter.
The door control setting (F2)
is set to value 3 (closed).
Change the door control setting (F2) to value 1
(automatic).
Once you have saved an access code, you always need to enter this code to unlock the sensor.
If you forget the access code, cut and restore the power supply. During 1 minute, you can access the sensor without
introducing any access code.
This product should be disposed of separately from unsorted municipal waste
PLEASE KEEP FOR FURTHER USE - DESIGNED FOR COLOUR PRINTING
ASSA ABLOY Entrance Systems AB hereby declares that the that the radio equipment type from the PASM24W is in compliance
with Directive 2014/53/EU (RED) and Directive 2011/65/EU (RoHS).
Landskrona, January 2021 Matteo Fino, authorized representative and responsible for technical documentation.
The complete declaration of conformity is available on our website