Dixie Narco P Series User manual

Pepsi-Cola High Visibility Vender
P-SERIES HVV
Models DN552P & DN756P
Beginning Production Run 6925CB
Manufactured by
Dixie-Narco, Inc.
P.O. Drawer 719
Williston, SC 29853-0719
803-266-5001
fax: [phone]
Visit us on the web: www.dixienarco.com
803,903,770.31

Page 2of 76
Table of Contents
GENERAL INFORMATION
Application......................................................................................................................................................... 4
Vender Safety Precautions............................................................................................................................. 4
Product Identification....................................................................................................................................... 4
Physical Characteristics .................................................................................................................................. 4
Receiving Inspection........................................................................................................................................ 4
AINSTALLATION & SETUP
Unpacking the Vender..................................................................................................................................... 5
Electric Power Requirements......................................................................................................................... 5
Ground the Vender........................................................................................................................................... 5
Pepsi Electronic Door Lock........................................................................................................................5 -6
Placing the Vender on Location..................................................................................................................... 6
Level the Vender .............................................................................................................................................. 6
Space the Vender............................................................................................................................................. 6
Coin Changers and Other Accessories ........................................................................................................ 7
Loading the Change Tubes ............................................................................................................................ 7
Loading Product................................................................................................................................................ 7
Initial Loading.................................................................................................................................................... 7
BPROGRAMMING
Normal/Service Mode...................................................................................................................................... 8
Historical Data................................................................................................................................................... 9
Interval Data –Resettable Data..................................................................................................................... 9
Set Price ............................................................................................................................................................ 9
Cash Settings............................................................................................................................................ 9 -10
User Menu...............................................................................................................................................11 -20
Diagnostics Menu..................................................................................................................................20 – 21
Quick Reference Prompts .............................................................................................................................22
Default Space-To-Sales Setting...................................................................................................................23
Set Vender Type.............................................................................................................................................24
CGENERAL MAINTENANCE
Power...............................................................................................................................................................25
Cleaning...........................................................................................................................................................25
Refrigeration Condenser...............................................................................................................................25
Coin Acceptor..................................................................................................................................................25
Lubricating the Vender..................................................................................................................................25
EPROM Replacement...........................................................................................................................26 -27
DMAJOR COMPONENT DESCRIPTION
Electrical..........................................................................................................................................................28
Refrigeration....................................................................................................................................................28
SBC Control Board.........................................................................................................................................29
ETROUBLESHOOTING FLOWCHARTS
All Coins are Rejected...................................................................................................................................30
All Bills are Rejected......................................................................................................................................31
Incorrect Change Dispensed........................................................................................................................32
Selection Will Not Vend.................................................................................................................................33
Ice / Frost on Evaporator...............................................................................................................................34
Compressor Runs Continuously..................................................................................................................34
Compressor Will Not Start ............................................................................................................................35
Machine Not Cooling......................................................................................................................................36
Can’t Enter the Menu or Diagnostics ..........................................................................................................37
Lights Are Not On ...........................................................................................................................................38
One or More Motors Run When Main Door is Closed..............................................................................39
Sold Out ..........................................................................................................................................................40
The Display is Dead.......................................................................................................................................41
Can’t Read the Display..................................................................................................................................42

GENERAL INFORMATION P-SERIES INSTALLATION & SETUP GUIDE
Page 3of 76
Table of Contents
FWIRING DIAGRAMS AND SCHEMATICS
Figure 1 –SBC Wiring Diagrams..........................................................................................................43-44
Figure 2–Compressor Wiring Diagram .....................................................................................................45
GPARTS LIST
MAIN DOOR EXTERIOR ........................................................................................................................46-47
MAIN DOOR INTERIOR (A) ...................................................................................................................48-49
MAIN DOOR INTERIOR (B) .........................................................................................................................50
SELECT PANEL.............................................................................................................................................51
T8 LIGHTING..................................................................................................................................................52
ELECTRONIC COMPONENTS .............................................................................................................53-54
INNER DOOR ...........................................................................................................................................55-56
CABINET AND VEND MECHANISM (SECTION1) ..................................................................................57
CABINET AND VEND MECHANISM (SECTION 2) ...........................................................................58-61
CABINET AND VEND MECHANISM (SECTION 3) .................................................................................62
CHUTE ASSEMBLY ..................................................................................................................................... 63
EVAPORATOR FAN ASSEMBLY.........................................................................................................64-65
POWER DISTRIBUTION BOX.....................................................................................................................66
HARNESSING................................................................................................................................................67
REFRIGERATION SYSTEM .................................................................................................................68-69
MISCELLANEOUS LABELS ........................................................................................................................70
SIGNS AND DECALS....................................................................................................................................71
SCREWS & NUTS ...................................................................................................................................72-73
WASHERS, BOLTS, & MISC. HARDWARE........................................................................................74-76
\

GENERAL INFORMATION P-SERIES
Page 4of 76
APPLICATION
This information applies to P-Series venders
manufactured the third quarter 2003 which have
significant differences in programming and parts
content from previous venders. To order parts or
information pertaining to this vender, please contact
Dixie Narco.
VENDER SAFETY PRECAUTIONS
Please read this manual in its entirety. This service
information is intended to be used by a qualified
service technician, who is familiar with proper and
safe procedures to be followed when repairing,
replacing, or adjusting any Dixie-Narco vender
components. All repairs should be performed by a
qualified service technician who is equipped with the
proper tools and replacement components, using
genuine Dixie-Narco factory parts.
REPAIRS AND/OR SERVICING
ATTEMPTED BY UNINFORMED
PERSONS CAN RESULT IN
HAZARDS DEVELOPING DUE TO
IMPROPER ASSEMBLY OR
ADJUSTMENTS WHILE
PERFORMING SUCH REPAIRS.
PERSONS NOT HAVING A PROPER
BACKGROUND MAY SUBJECT
THEMSELVES TO THE RISK OF
INJURY OR ELECTRICAL SHOCK
WHICH CAN BE SERIOUS OR EVEN
FATAL.
PRODUCT IDENTIFICATION
First production of P-Series August 2003
The production date of Dixie-Narco products is
determined by the date code incorporated in the
serial number.
The vender serial number takes the form yyyyzz-
xxxx.The last 4 digits (xxxx) identify the specific
vender. The first 4 digits (yyyy) identify the
manufacturing run that the vender was built in. The
two alpha characters (zz) identify the quarter and the
year the vender was built. The first alpha-character
identifies the quarter.
A = 1st quarter
B = 2nd quarter
C = 3rd quarter
D = 4th quarter
The second alpha-character identifies the year:
B = 2003
C = 2004
D = 2005
PHYSICAL CHARACTERISTICS
552P 756P
HEIGHT 72” 72”
WIDTH 28” 36”
DEPTH 33.5” 33.5”
DEPTH WITH
VALIDATOR
N/A N/A
SHIPPING WEIGHT 600 lbs. 788 lbs.
Loaded Weight 4 Deep
Cans
1134 lbs lbs
Model # of
Selections
# of Wide
Columns
# of Narrow
Columns
552P 624
756P 12 35
RECEIVING INSPECTION
Upon receipt, inspect the vender for any shipping
damage. If there is any damage have the driver
note the damage on the bill of lading and notify
Dixie-Narco.
Although the terms of sale are FOB shipping point,
which requires the consignee to originate shipping
damage claims, Dixie-arco will gladly help if you
must file a claim.

INSTALLATION & SETUP P-SERIES
Page 5of 76
The Dixie-Narco P-Series vender is designed
utilizing the latest technology.
UNPACKING THE VENDERS
Remove the stretch wrap and top cover from the
vender. Product cards are installed in the select
buttons.
DO NOT STORE THE VENDER
OUTSIDE WITH THE STRETCH
WRAP ON. THIS COULD CAUSE
THE STRETCH WRAP TO BOND
TO THE VENDER’S SURFACE,
WHICH COULD DAMAGE THE
FINISH.
Remove the shipping boards from the bottom of the
vender. The shipping boards are attached by the
leveling legs. To avoid unnecessary damage to the
leveling legs or base, remove the shipping boards by
using a 1½” “socket type” wrench to unscrew the
leveling legs. Be sure to replace the legs after
removing the shipping boards.
WARNING
TO AVOID THE POSSIBILITY OF A
FIRE HAZARD, DO NOT STORE
ANYTHING OR ALLOW DEBRIS OF
ANY KIND TO ACCUMULATE IN
THE BOTTOM OF THE DOOR, IN
AND AROUND THE
REFRIGERATION COMPARTMENT
OF THE CABINET, OR IN FRONT
OF THE EVAPORATOR AND
CONDENSER COILS.
ELECTRIC POWER NEEDED
Refer to the cabinet serial number plate to determine
the proper voltage and frequency the machine
requires (domestically this requirement is 120 Volts,
60 Hertz). The cabinet serial plate also indicates the
Amperage of the vender. The vender must be
plugged into a properly rated, single phase
alternating current outlet with its own circuit
protection (fuse/circuit breaker).
DO NOT USE AN EXTENSION CORD.
GROUND THE VENDER
The vender is equipped with a three-wire power
supply cord and MUST be plugged in a properly
grounded outlet.
DO NOT REMOVE THE GROUND PIN OR IN ANY
WAY BYPASS, MODIFY, DEFEAT, OR DESTROY
THE GROUNDING SYSTEM OF THE VENDER.
If the outlet will not accept the power cord plug,
contact an electrician to install a proper AC outlet.
FAILURE TO COMPLY WITH
THESE INSTRUCTIONS MAY
SUBJECT THE USER TO THE RISK
OF INJURY OR ELECTRICAL
SHOCK WHICH CAN BE SERIOUS
OR FATAL.
ELECTRONIC DOOR LOCK (OPTION)
The electronic lock when provided in the vender
consists of a door mounted, motor driven bayonet
(shaft) system, a cabinet mounted nut receptacle
switch system, an infrared controlled CPU, and a
remote control key (FOB). The design is modular
and allows for easy field service.
The electronic remote key (FOB) features a rolling
code system which cannot be decoded if it is lost or
stolen. After the vender has been unlocked, a new
key can be programmed into it any number of times.
If a key is lost or stolen, it is recommended you
change the lock code in the field as soon as
possible. Changing the lock code requires a new
key and pressing the LEARN button inside the
vender. The lock does not need to be changed for
re-keying.
Important: For security reasons all Electronic
Door Lock Venders are shipped less
keys. Customers will need to
contact the Electronic Door Lock
manufacturer to order keys.
A power bypass connector, located in the product
delivery port, allows auxiliary power to be applied via
a battery pack to the electronic lock in the event that
power is not available or there has been a failure of
the internal power supply. In the event of an
emergency, battery power is applied to the
connector and the door can be opened and closed
using the FOB.
The electronics use an infrared transmission system,
which functions similar to a television remote control.
The transmission signal is line-of-sight, which
requires you to aim the remote at a specific place at
close range to prevent the accidental opening of
several venders at the same time.

INSTALLATION & SETUP P-SERIES
Page 6of 76
TO OPEN THE ELECTRONIC DOOR LOCK:
(OPTION)
1. Plug the vender into a properly powered
outlet.
2. Hold the key FOB 0 to 3 inches to the right
side of select button #10 in 12 select or elect
button #5 in 6 select and press the button on
the key FOB.
Note: The wide end of the FOB should
face the door.
3. The lock will begin releasing the door. The
display will indicate Door opening.
After the motor has stopped running, you
can pull the door open. The display will
indicate: Door unlocked.
TO CLOSE THE ELECTRONIC DOOR LOCK:
CAUTION: DO NOT SLAM THE DOOR CLOSED.
Slamming the door closed can damage the
electronic locking device.
1. Push the door to the cabinet until the lock
motor starts. The display will indicate: Door
closing.
2. Continue to push the door for approximately
2 to 3 seconds after the lock motor starts.
The lock will pull the door closed tightly.
3. When the lock motor stops the door will be
locked and the display will indicate:Door
locked.
Before leaving the vender, ensure that the
door is locked.
The electronic door lock assembly is supplied by Tri
Teq Lock and Security. Dixie-Narco, Inc. does not
carry parts for the Tri Teq Electronic Door Lock.
For parts and assistance, please contact:
Tri Teq
701 Gullo Ave.
Elk Grove Village, IL 60007
Tel: [phone]
Fax: [phone]
Email: [email protected]
PLACING THE VENDER ON LOCATION
!! CAUTION !!
DO NOT TRANSPORT THE
VENDER TO OR FROM THE
LOCATION LOADED WITH
PRODUCT.
DAMAGE TO THE VENDER MAY
RESULT.
The vender must be located on a solid, flat, and
level surface. Ensure the flooring can bear the
weight of a fully loaded vender (approximately 1134
lbs.) The vender must be positioned close enough
to an electrical outlet that an extension cord is not
required. If the machine will be subject to user
misuse or vandalism, it is recommended that the
vender be secured to the floor or wall as described
in Dixie-Narco Technical Bulletin 344. Call the Dixie-
Narco Technical Service Department or your Dixie-
Narco Representative for assistance.
LEVEL THE VENDER
When the vender is level, the door can be opened to
any position and it will not move by itself. Open the
door to several different positions before deciding
the vender is level. A carpenter’s level will help
verify the machine is level.
Make sure that all leveling legs are in contact with
the floor. If you cannot level the vender in its current
location, select another location. DO NOT place any
objects under the machine.
DANGER
THE VENDER MUST BE
PROPERLY LOCATED AND
LEVELED. IF THE MACHINE WILL
BE SUBJECT TO USER MISUSE
OR VANDALISM IT IS
RECOMMENDED THAT THE
VENDER BE SECURED TO THE
FLOOR OR WALL AS DESCRIBED
IN DIXIE-NARCO TECHNICAL
BULLETIN 344 TO MINI MIZE THE
RISK OF INJURY OR DEATH
FROM TIPPING. CALL THE DIXIE-
NARCO TECHNICAL SERVICE
DEPARTMENT OR YOUR DIXIE-
NARCO REPRESENTATIVE FOR
ASSISTANCE.
SPACE THE VENDER
Do not block the rear of the vender. Keep the vender 4
inches (10 cm) from the wall to ensure adequate airflow to
the condenser and compressor. At the front of the vender,
make sure that nothing obstructs the air intake at the
bottom of the main door. At the rear of the vender, make
sure nothing obstructs the air exhaust at the bottom of the
cabinet.
WARNING
TO AVOID THE POSSIBILITY OF A
FIRE HAZARD, DO NOT STORE
ANYTHING OR ALLOW DEBRIS OF
ANY KIND TO ACCUMULATE IN
THE BOTTOM OF THE DOOR, IN
AND AROUND THE
REFRIGERATION COMPARTMENT
OF THE CABINET, OR IN FRONT
OF THE EVAPORATOR AND
CONDENSER COILS.

INSTALLATION & SETUP P-SERIES
Page 7of 76
COIN CHANGERS & OTHER
ACCESSORIES
The vender must have an MDB coin changer
installed and can have an MDB bill acceptor
installed. If the MDB coin changer and other MDB
accessories are not factory installed, refer to the
instructions received from the manufacturer of the
MDB coin changer and other MDB accessories for
proper set-up and installation.
The vender will support the following MDB coin
changers:
Multi-Drop Coin Mech (Domestic)
Coinco 9302GX
Coinco USQ G700 Series
Conlux USLZ-101
Conlux CCM5G
Mars 4510
Mars 6512
The vender will support the following MDB bill
validators:
Multi-Drop Bill Validators (Domestic)
Coinco BA30B, BA50, MAG30, MAG50
Mars VN2512, VN2502, VN2312
Conlux NBM-3000 Series, NBU-2111-12
Ardac 5500 Series
The vender will support the following MDB card
readers:
At publication, card reader dispositions were
not available. Contact card reader
manufacturer for proper installation and
setup.
LOADING CHANGE TUBES
Open the main door and enter the “FILL CM” mode
in the “CASH SET” sub-menu in Programming (see
Section B –Programming).
Load the coin mechanism with coins by inserting
coins in the coin mech’s separator. The display will
show the total value of coins as they are inserted.
Note: A low coin level in the coin tubes will
interfere with operation of the bill validator.
For additional information about coin mechanisms,
refer to the specific manufacturer’s instructions.
Loading Product
The P-Series Vender is designed to vend a wide
range of packages.
All P-Series Venders are shipped ready to vend
packages according to customers orders. To vend
an alternative package in the P-Series vender,
contact Dixie Narco Technical Service Dept. or your
Representative For Assistance.
INITIAL LOADING
To ensure proper vending, make sure wide columns
all set to vend the proper packages. When loading a
wide column, the first row of packages should be
loaded on the bottom bar of the oscillator. The
second row of packages must be loaded on the top
bar of the oscillator. Always load complete rows; do
not load only to the back or only to the front of the
column.
The narrow column rotors must be in the “cup”
position to receive the first row of packages. When
loading narrow columns, lay the first row of
packages in the rotor. The second row of packages
must be loaded on the load bar.
Correct loading will prevent service calls and ensure
proper vending.
After loading the vender for the first time, ensure the
vender is loaded and primed. Priming is done in
programming. The depth must also be
programmed depending on the package to be
vended. Cans may be programmed up to 4 deep.
NOTE: To ensure proper airflow through the
evaporator, DO NOT place packages (or
other foreign objects) in the bottom of the
tank.
SERVICE NOTE
Battery Backup (SBC)
The Single Board Controller is equipped with a battery
backup which is used to retain information programmed in
the system (pricing, time, date, etc.) in case of power
interruptions or any time the main power is off. When the
vender is shipped, the battery is connected and memory is
being maintained.
Disconnect the battery if the vender will be stored for a
long period of time. The following steps will guide you
through this procedure.
ØRemove power from the vender by unplugging
the main power cord from the wall receptacle.
ØLocate the Control Board on the main door.
Remove the battery from its holder (B1).

INSTALLATION & SETUP P-SERIES
Page 8of 76
SBC
PROGRAMMING METHOD
AUGUST 2003
P-SERIES
HVV
The controller has two modes of operation:
NORMAL and SERVICE.
NORMAL MODE:
In Normal Mode, on power up display will show the software version installed in vender for 10 Seconds, then
change to Ice Cold Drink message, Product Price, Sold Out, Credit Value, or decimal point. If the right most
decimal is fl ashing, this indicates an error or problem recognized in the vender. When money is inserted, the
display indicates the total amount of the deposit. The select buttons are used to select the product. In normal
mode you may access an external menu for reading historical sales total, product total, product total by selection,
sales by price totals, and machine temperature.
Note: If “SCOL” appears on the display on power up with the door open, you will need to program the vender
model number in the controller. Refer to Setting the Vender Type on page 25.
SERVICE MODE:
The Service Mode is entered when the vender door is open and the service switch is pressed. The display will
show a list of error codes for errors that have occurred since the door was last opened. "Jammed Column #” is a
vend mechanism jammed, "Select Switch #" is a select switch problem, “Refrigeration” is a refrigeration or temp
sensor problem, and “Door Switch” is a door switch open problem. To acknowledge an error, press select button
1, at this time you will enter the service menu. The display will show "Historical Data" at this time. Some of the
menu items have sub-menus.
To move through the menus and sub-menus follow these instructions. To:
MOVE THROUGH MENU: Press select buttons 1 & 2 simultaneously to scroll down through the menu.
While scrolling down through menu, release for 2 seconds, press select
buttons 1 & 2 simultaneously to scroll up through menu.
ENTER SUB -MENU: Press and hold select button 1 to enter a sub-menu.
EXIT SUB-MENU: With "Return" on display, press and hold select button 1 to exit a sub-
menu.
EXIT SERVICE MODE:
Closing the inner door, pressing button 1 when “Return” is displayed at the top menu level, or a five-minute
inactivity time-out will exit the service mode.

PROGRAMMING P-SERIES
Page 9 of 76
FRONT PANEL PROGRAMMING
SERVICE MENU
Historical Data
This function shows the user the vender accounting over the life of the vender. Use the following select buttons to
view the total sales in dollars, total number of vends and the total number of vends for each selection.
Press Select Button 1: Shows the historical total cash sales for the life of the vender.
Press Select Button 2: Shows the historical total number of vends.
Press Select Button 3: Shows the historical number of vends by selection. Each selection automatically scrolls
across the display.
Press & hold select buttons 1 & 2 simultaneously to move to the next item on the menu.
Resettable Data
This function shows the user the vender accounting data since the last counter reset. This data can be reset
either from the menu or by DEX interrogation.
Press Select Button 1: Shows the total cash collected since the last counter reset
Press Select Button 2: Shows the total number of vends since the last counter reset.
Press Select Button 3: Shows the total number of vends by selection since the last counter reset Each selection
automatically scrolls across the display.
Press Select Button 4: This button zeros the interval data described above. Hold select button “4” for 5 seconds,
“the display will go blank” then “Counters Reset” will be displayed. At this time, all interval
data will return to “0”.
Set Price
This function is used to set the price of each selection. When a select button is pressed, the price for that
selection will be displayed. If the button is held in, the price will increment or decrement. To change from
increment to decrement, release the select button and press it again. To set all selections for the same price: set
the desired vend price on select #1, then simultaneously press and hold buttons 3 & 4, the price set for select #1
will be displayed. After 5 seconds the display will show “Single Price Set”, this will change the vend price of all
selections, both primary and secondary, to the price programmed to button #1.
Note: The SBC multi-pricing capability allows you to set all the selections to any price in the range of $0.00 to
$99.95.
Press & hold select buttons 1 & 2 simultaneously to move to the next item on the menu.
Cash Settings
This function is used to configure credit handling rules for the vender. To move to “User Menu”, press & hold
select buttons 1 & 2 simultaneously. Press button 1 to enter Cash Settings Menu. The following are sub-menus
of the Cash Settings: Fill Coin Mech, Dump Coin Mech, Coin Rules, Escrow, Multi Vend, and Return.
Fill Coin Mech:
This function is used to count coins loaded in the top (separator) of the coin mech. When Fill Coin Mech
is displayed the coin mech will accept tubed coins. When the first coin is inserted, Fill Coin Mech will be
replaced with the cash value of coins in the coin tubes. The total value of the coins inserted will be
displayed and will be counted in the DEX audit data, so the controller knows exactly how much change is
in the coin mech.
Press & hold buttons 1 & 2 simultaneously to move to the next item on the menu.

PROGRAMMING P-SERIES
Page 10 of 76
Dump Coin Mech:
This function is used to dump coins from the coin mechanism. Press select button #1 to enter mode and
the lowest coin value dispensable will show on the display. Press and hold select buttons 1 & 2
simultaneously to scroll through the different coin values available to dump coins. Press and hold select
button #1 to dump the coins whose value is shown on the display. Press and hold select buttons 1 & 2
simultaneously until “Return” shows on the display. Press select button #1 will return to “Dump Coin
Mech”.
If a level 3 coin mech with Alternate Payout mode is installed, the coin mech will stop
dispensing coins when the coin mech’s coin count reaches 0.
Coin Rules:
This condition is used to allow the exact change condition to be turned on or off. When off, the controller
will not go in the exact change condition. This will allow bills or coins to be accepted regardless of the
ability to pay back non-refundable currency. When turned on, the controller will set the exact change
condition based on the ability to pay back non-refundable currency (i.e. Coins, paper). To show current
condition press select button 1. Press and hold select button 1 to toggle “Coin Rules” on and off.
Escrow:
This function supports 4 (four) escrow options. Pressing select button 1 will show the current escrow
setting. Press and hold select button 1 to scroll through the available Escrow options and set the escrow
mode to the setting displayed when select button1 is released.
Price 1
This escrow condition is forced vend option 1 (“escrow to price”). All dollar bills will be stacked.
No cancel sale is allowed once minimum vend price is met or exceeded.
Price 2
This escrow condition is forced vend option 2 (“escrow no cancel”) with all bills stacked, and no
cancel sale allowed unless the vender is in exact change and the maximum vend price is
exceeded. Note: Any money entered below the vend price cannot be returned.
Select 4
This escrow condition is “escrow to select” with all the dollar bills being stacked. Cancel sale will
return the deposit from the coin changer (i.e.4 quarters).
Select 1
This escrow condition is “escrow to select dollar bills” with the last dollar bill that meets or
exceeds maximum vend price being escrowed in the validator. Cancel sale will return the held
dollar bill and any amount over $1 will be returned from the coin changer.
Press & hold select buttons 1 & 2 simultaneously to move to the next item on the menu.
Multi Vend:
This function, when turned on, allows credit to be retained after a vend so the customer can vend from
another selection. (i.e..50 vend price, put in $1.00, push a select button and vends, .50 still shows on the
display, push a second select button and vends). Credit is cancelled after 5 minutes of inactivity. There
is unlimited acceptance. If a customer wants their credit (money) back, the coin return lever must be
pressed. To show the current “Multi Vend” condition, press select button 1 and the display will show the
current setting. Press and hold button 1 to toggle “Multi Vend” on and off.
Press and hold select buttons 1 & 2 simultaneously to move to “Return”.
Return:
Press and hold button 1 to return to “Cash Settings”.

PROGRAMMING P-SERIES
Page 11 of 76
User Menu:
This function is used to configure the vender to operate in a fashion best suited for the vender location. To move
to “Diagnostics”, press & hold select buttons 1 & 2 simultaneously, to enter the User Menu sub-menus press
select button1. The following are sub-menus of the User Menu for a machine with AC motors: Space To Sales,
Column, Time, Language, Electronic Counter, Limited Access, Secondary Price, Environmental Controls, Light,
Refrigeration, Free Vend, Override, Sales Message, Recharge, and Return. The “Column” sub-menu prompt will
only be available in machines with DC motors.
Space To Sales
To view the space to sales condition, press select button 1 and display will show “Selection 1”. Alternating
with columns assigned to that select button. Press select buttons 1 & 2 simultaneously to scroll through
the available select buttons to view columns assigned and “Return”.
To change space to sales:
Press select button 1 at the “Selection #” prompt and “Column ## #” (column edit routine) will be
displayed, where the ## is the column to be added or deleted to the select button and the third #
is “0” for not assigned or “1” for assigned to that selection. Press select button 1 with “Column ##
#” on the display to toggle between “Column ## 0” and “Column ## 1”. With the setting you wish
to use showing on the display, press select buttons 1 & 2 to scroll to next selection to add/delete
columns. Press select button 1 at the “Return” prompt when selecting columns to enable, will
return to “Selection #”.. Press select button 1 at the “Return” prompt when choosing what
selection to set for Space to Sales, will return to “Space to Sales”.
Note: You must be in the “Selection” prompt to get to the “Return” mode that scrolls to “Space To
Sales”.
Press & hold select buttons 1 & 2 simultaneously to move to the next item on the menu.
Column -This prompt only appears on machines with DC motors.
Select this prompt to set column depth, package type and vend angles if the package type is custom. This
will scroll through the list of columns 1--- 9, “ALL” or “Return” to select what column(s) will have its
settings changed. Pressing button 1 will display “Column # ” where # represents the column number.
Pressing select buttons 1 & 2 simultaneously will scroll through the columns.
Press select button 1 to scroll to “Package”
“Package” -is the next prompt. Press select buttons 1 & 2 simultaneously after entry into this
sub-menu will toggle between “Package” and “Return”. Selecting this allows setting the package
type for the column selected in the column prompt. Pressing select button 1 will show current
package setting. (i.e.1, 2, 3, …, Custom, and Return ). Press select buttons 1 & 2 simultaneously
to scroll through the package settings.
Press select button 1 to select the package type.
If a predefined package type(1, 2, 3, 4, or 5) is selected
After the package type has been selected, “Key 1 = Prime, Key 2 = Exit” will be displayed. Press
button 1 to prime the column with product or button 2 to exit without priming the column. If select
button 2 is pressed the column will be marked as jammed and will prime when the door is closed.
“Hold Angle” -Will only be displayed if the package type selected is custom.
This allows setting the hold angle for the column selected in the column prompt. Press select
button 1 to display the current hold angle “Hold Angle ###. Press select buttons 1 & 2
simultaneously to scroll through hold angles. Press select button 1 to select the displayed hold
angle. “Depth” will be displayed after the hold angle is set.
“Depth” -Will only be displayed if the package type selected is custom.
This allows setting the product depth for the column selected in the column prompt. The current
product depth “Depth #” is displayed when select button 1 is pressed. Press select buttons 1 & 2
simultaneously to scroll through available product depths. Press select button 1 to select the
displayed depth.

PROGRAMMING P-SERIES
Page 12 of 76
“Vend Angle” -Will only be displayed if the package type selected is custom.
This allows setting the vend angles for the column selected in the column prompt. “Vend Angle #
### will be displayed where the first # is the product number in the column and ### is the vend
angle for that product. The user will be prompted to enter to same number of vend angles as was
entered at the “Depth” prompt. After the last vend angle is entered the display will show “2 =
Exit, 1 = Prime”. Press button 1 to prime the column with product or 2 to exit with out priming the
column. If select button 2 is pressed the column will be marked as jammed and will prime when
the door is closed.
Return
Pressing select button 1 will return to “Column”
Press and hold select buttons 1 & 2 simultaneously to move to the next item on the menu
Time
This function is used to set the year, month, day, hour/minute (military 24 hour clock), and daylight
savings time. Press select button 1 and “Year” will show on display. Press select buttons 1 and 2
simultaneously to scroll through all “Time” sub-menus.
“Year”- Year Setting (2000 to 2099)
Press select button 1 the current year setting will show on display.
Press and hold select button 1 to increment the year setting (2000 to 2099).
Release select button 1 and press and hold again will decrement the year setting.
Release the select button with the display showing the year you wish to use and display will
return to “Year”.
Press select buttons 1 & 2 simultaneously to scroll to “Month”.
“Month” -Month Setting (01 to 12)
Press select button 1 and the current 2-digit month setting will show on display.
Press and hold select button 1 to scroll through the month settings. (01 = Jan. to 12 = Dec).
Release the select button with the display showing the month you wish to use and display will
return to “Month”.
Press select buttons 1 & 2 simultaneously to scroll to “Day”.
“Day”-Day of Month Setting (1 to 31)
Press select button 1 and the current 2-digit day of month setting will show on display.
Press and hold select button 1 to scroll through the day of month settings (1 to 31).
Release select button 1 and press and hold again will decrement the day of month setting.
Release the select button with the display showing the day of month setting you wish to use and
display will return to “Day”.
Press select buttons 1 & 2 simultaneously to scroll to “Hour/Minute”.
“Hour/Minute” -Hour and Minute Setting (0000 to 2359)
Press select button 1 and the current 4-digit hour and minute setting will be displayed (24 hour).
Press and hold select button 1: Set Hours
Press and hold select button 2: Set Minutes
Press select buttons 1 & 2 simultaneously to move to the next item in the menu.

PROGRAMMING P-SERIES
Page 13 of 76
Daylight Savings Time
Press select button 1 and the current setting will show on the display.
Press and hold select button 1 to scroll through the “Daylight Savings Time” options listed:
“American” –North American rules –Set forward 1 hour at 2:00 am on the first Sunday
in April; Set backward 1 hour at 2:00 am on the last Sunday in October.
“European” –European rules –Set forward 1 hour at 1:00 am on the last Sunday in
March; Set backward 1 hour at 1:00 am on the last Sunday in October.
“Australian” –Australian rules –Set forward 1 hour at 1:00 am on the first Sunday in
October; Set backward 1 hour at 1:00 am on the last Sunday in March.
“Off” –Off Rules–Daylight savings time change will not be made.
Release the select button with the display showing the “Daylight Savings Time” setting
you wish to use and display will return to “Daylight Savings Time”.
Press and hold select buttons 1 & 2 simultaneously to move to “Return”.
Return:
Press select button 1 to return to “Time”.
Language
This function is used to set the language that will be used for sales mode messages. To display the
current language selected, press select button 1. To change the language selected, press & hold select
button 1 to scroll through the language menu. Once the desired language is shown on the display,
release the button. The display will then return to "Language".
English Spanish
French Slovene
German Finnish
Italian Norwegian
Portuguese
Press and hold select buttons 1 & 2 simultaneously to move to the next item on the menu.
Electronic Counter
This function is used to set the four (4) button code that will show historical cash sales, historical
total vends, historical product counts by selection, historical product
counts that have occurred for prices, and cabinet temperature when the
vender is in sales mode. Press select button 1 to view the current four
(4) button code.
To change "Electronic Counter" four button code:
At "Electronic Counter" press select button 1, "####" (representing current four button code) will show on
display (“4231” is the factory default code). Press and hold select button 1 until the far left digit is
replaced by an “*” indicating it can be changed. Press the select button desired for the first digit of the
code. The next digit will be replaced by an “*” press the select button desired for that digit of the code.
Continue this process until all 4 digits are set. After the last digit is entered the display will return to
“Electronic Counter”

PROGRAMMING P-SERIES
Page 14 of 76
Note: The four-button code must use select buttons 1 through 9 only.
Enter the four button code while in sales mode to view the data. Once entered the listed data is available
from the front of the vender:
Press select button 1: Show historical cash sales.
Press select button 2: Show historical total vends.
Press select button 3: Show historical product counts by selection.
Press select button 4: Show historical cash sales by selection
Press select button 5: Show temperature inside the cabinet.
Press select button 6: Returns to sales idle mode (sales vender operation).
Note: There is a thirty (30) second time-out that will return the vender to sales mode if no select buttons
are pressed.
Press & hold select buttons 1 & 2 simultaneously to move to the next item on the menu.
Limited Access
This function is used to program the vender to use the Limited Access Features. To move to Secondary
Price Menu, press & hold select buttons 1 & 2 simultaneously, to enter the sub-menu press select button
1. The following are sub-menus of the Limited Access Menu: "Selects", "Days”, “Start 1”, “Stop 1”, “Start
2”, “Stop 2”, and “Return”.
Selects
This function is used to set selection(s), which, will be limited during certain periods of the day.
To view the selection setting condition, press select button 1. The display will show "Selects## #
where ## is the selection number and # is a “0” or “1” depending on whether the selection is
enabled (1) or disabled (0). Press and hold select button 1 to toggle between “0” & “1. Press
select buttons 1 & 2 simultaneously to scroll through all available select buttons, “NONE”, “ALL”,
and “Return”. Pressing select button 1 when “ALL” is” displayed will cause the display to change
to “on” when all selections have been enabled. Pressing select button 1 when “NONE” is”
displayed will cause the display to change to “off” when all selections have been disabled. Press
select button 1 at the “Return” prompt returns to “Selects”.
Press & hold select buttons 1 & 2 simultaneously to move to the next item on the menu.
Days
This function is used to set the days of the week to be affected by limited access.
Day of Week: Sunday Wednesday Saturday Return
Monday Thursday All Days
Tuesday Friday No Days
Press select button 1 and "Monday #" will show on the display, where # is “0” (disable) or “1”
(enable). Press and hold select button 1 to toggle between “0” and “1”. Release the select button
with the display showing the setting you wish to use. Press select buttons 1 & 2 simultaneously
to scroll through all available days, “All Days”, “No Days”, and “Return”. Pressing select button 1
when “ALL Days” is” displayed will cause the display to change to “on” when all days have been
enabled. Pressing select button 1 when “No Days” is” displayed will cause the display to change
to “off” when all days have been disabled. Press select button 1 at the “Return” prompt returns to
“Days”.
Press & hold select buttons 1 & 2 simultaneously to move to the next item on the menu.
Start 1
This function is used to set the hours and minutes to start period 1 limited access. Press select
button 1 and the current four-digit hour and minute setting will to be displayed (24 hour).
Press & hold select button 1: Set Hours
Press & hold select button 2: Set Minutes
Press select buttons 1 & 2 simultaneously to move to the next item in the menu.

PROGRAMMING P-SERIES
Page 15 of 76
Stop 1
This function is used to set the hours and minutes to stop period 1 limited access. Press select
button 1 and current four-digit hour and minute will be displayed. (24 hour).
Press & hold select button 1: Set Hours
Press & hold select button 2: Set Minutes
Press select buttons 1 & 2 simultaneously to move to the next item in the menu.
Start 2
This function is used to set the hours and minutes to start period 2 limited access. Press select
button 1 and the current four-digit hour and minute setting will be displayed (24 hour).
Press & hold select button 1: Set Hours
Press & hold select button 2: Set Minutes
Press select buttons 1 & 2 simultaneously to move to the next item in the menu.
Stop 2
This function is used to set the hours and minutes to stop period 2 limited access. Press select
button 1 and the current four-digit hour and minute setting will be displayed (24 hour).
Press & hold select button 1: Set Hours
Press & hold select button 2: Set Minutes
Press select buttons 1 & 2 simultaneously to move to the next item in the menu.
Return
Press select button 1 to return to “Limited Access”.
Press & hold select buttons 1 & 2 simultaneously to move to the next item on the menu.
Secondary Price
This function is used to program a second price for each selection. To move to Environmental Controls,
press & hold select buttons 1 & 2 simultaneously. To enter the sub-menu press select button 1. The
following are sub-menus of the Secondary Price Menu: “Price”, “Days”, “Start”, “Stop”, and “Return”.
Price
This function is used to set the price of each selection. When a select button is pressed, the price
For that selection will be displayed. If the button is held in, the price will increment or decrement.
To change from increment to decrement, release the select button and press it again.
Note: The SBC multi-pricing capability allows you to set all selections to any price in the range
of $0.00 to 99.95.
Press & and hold select buttons 1 & 2 simultaneously to move to the next item on the menu.
Days
This function is used to set the days of the week to be affected by secondary pricing.
Day of Week: Sunday Wednesday Saturday Return
Monday Thursday All Days
Tuesday Friday No Days
Press select button 1 and “Monday #” will show on the display, where # is “0” (disable) or “1”
(enable). Press and hold select button 1 to toggle between “0” and “1”. Release the select button
with the display showing the setting you wish to use. Press select buttons 1 & 2 simultaneously
to scroll through all available days, “All Days”, “No Days”, and “Return”. Pressing select button 1
when “ALL Days” is” displayed will cause the display to change to “on” when all days have been
enabled. Pressing select button 1 when “No Days” is” displayed will cause the display to change
to “off” when all days have been disabled. Press select button 1 at the “Return” prompt returns to
“Days”.

PROGRAMMING P-SERIES
Page 16 of 76
Press & hold select buttons 1 & 2 simultaneously to move to the next item on the menu.
Start
This function is used to set the hours and minutes to start secondary pricing. Press select button
1 and the current four-digit hour and minute setting will be displayed. Press and hold select button
1 to change the hour setting, press button 2 to change the minute setting.
Press select buttons 1 & 2 simultaneously to move to the next item in the menu.
Stop
This function is used to set the hours and minutes to stop secondary pricing. Press select button
1 and the current four-digit hour and minute setting will be displayed. Press and hold select button
1 to change the hour setting, press button 2 to change the minute setting.
Press select buttons 1 & 2 simultaneously to move to the next item in the menu.
Return
Press button 1 to return to Secondary Pricing
Press buttons 1 & 2 to scroll to the next item in the menu
Environmental Controls
This allows the user to view the energy conservation menu “Lighting”, Refrigeration”, and also the “Relay”
test menu. When this is programmed to “OFF” you will not see “Lighting”, Refrigeration or Relay
Test. Press select button 1 and the current setting will be displayed (On or Off). Press and hold select
button 1 to toggle between on and off (This feature is “OFF” from the factory). To move to Light, press
& hold select buttons 1 & 2 simultaneously with this feature on. To move to Free Vend, press & hold
select buttons 1 & 2 simultaneously with this feature off.
Light
This function is used to turn the lights off during certain periods of the day. To enter the sub-menu press
select button 1. The following are sub-menus of the Light Menu: “Days”, “Start”, “Stop”, “Enable”, and
“Return”. To move to Refrigeration, press & hold select buttons 1 & 2 simultaneously.
Pressing select button 1 will enter “Days”.
Days
This function is used to set the days of the week to turn lights off.
Day of Week: Sunday Wednesday Saturday Return
Monday Thursday All Days
Tuesday Friday No Days
Press select button 1 and "Monday #" will show on the display, where # is “0” (disable) or “1”
(enable). Press and hold select button 1 to toggle between “0” and “1”. Release the select button
with the display showing the setting you wish to use. Press select buttons 1 & 2 simultaneously
to scroll through all available days, “All Days”, “No Days”, and “Return”. Press select button 1 at
the “Return” prompt returns to “Days”.
Press & hold select buttons 1 & 2 simultaneously to move to the next item on the menu.
Start
This function is used to set the hours and minutes to start lighting routine.
Press select button 1 and the current four-digit hour and minute setting will be displayed.
(24 hour).
Press & hold select button 1: Set Hours
Press & hold select button 2: Set Minutes
Press select buttons 1 & 2 simultaneously to move to the next item on the menu.

PROGRAMMING P-SERIES
Page 17 of 76
Stop
This function is used to set the hours and minutes to stop lighting routine.
Press select button 1 and the current four-digit hour and minute setting will be displayed.
(24 hour)
Press & hold select button 1: Set Hours
Press & hold select button 2: Set Minutes
Press select buttons 1 & 2 simultaneously to move to the next item on the menu.
Enable
This function is used to allow the lighting routine to go in to affect.
Press select button 1 and the current setting will be displayed (On or Off).
Press and hold select button 1 to toggle between “On” and “Off”.
Release the select button showing the setting you wish to use and display will return to “Enable”.
Press select buttons 1 & 2 to scroll to “Return”.
Return
Press select button 1 to return to “Light”.
Press & hold select buttons 1 & 2 simultaneously to move to the next item on the menu.
Refrigeration
This function is used to electronically control the refrigeration operations of the vender. . To enter the sub-
menu press select button 1. The following are sub-menus of the Refrigeration Menu: “Temperature”,
“Celsius or Fahrenheit “, “Display”, “Days”, “Start”, “Stop”, “Storage Temperature” , “Storage Enabled”,
and “Return”. To move to Free Vend, press & hold select buttons 1 & 2 simultaneously.
Press select button 1 will enter “Temperature”.
Temperature
(Default Temperature 350F/150C)
This function is used to set the average product temperature for initial pull down and reload
recovery.
Press select button 1 and “tt.tx” will show on the display where x is Fahrenheit or
Celsius and tt.t is the degrees.
Press and hold select button 1 to increase or decrease the number by 1F or 0.5C. Release
select button with the display showing the temperature you wish to use and display will
return to “Temperature”.
Press select buttons 1 & 2 to scroll to “Celsius or Fahrenheit”.
Celsius or Fahrenheit
This function is used to set the degree reading to Fahrenheit or Celsius.
Press select button 1 and the current setting will show on the display. Press and hold select
button 1 to toggle between Fahrenheit and Celsius. Release the select button with the display
showing the setting you wish to use and display will return to “Celsius or Fahrenheit”.
Press select buttons 1 & 2 to scroll to “Display”.
Display
This function is used to enable the Temperature to be displayed following the “Ice Cold Drink”
message. “Sales Message” must also be set to ON for the temperature to be displayed.
Press select button 1 and “Display” will show on the display. Press select button 1 and the
current setting will be displayed (On or Off). Press and hold select button 1 to
toggle between “On” and “Off”.
Press & hold select buttons 1 & 2 simultaneously to move to the next item on the menu.

PROGRAMMING P-SERIES
Page 18 of 76
Days
This function is used to set the days of the week to use Temperature Setting Routine.
Day of Week: Sunday Wednesday Saturday Return
Monday Thursday All Days
Tuesday Friday No Days
Press select button 1 and “Monday #” will show on the display, where # is “0” (disable) or“1”
(enable). Press and hold select button 1 to toggle between “0” and “1”. Release the select button
with the display showing the setting you wish to use. Press select buttons 1 & 2 simultaneously
to scroll through all available days, “All Days”, “No Days”, and “Return”. Press select button 1 at
the “Return” prompt returns to “Days”.
Press & hold select buttons 1 & 2 simultaneously to move to the next item on the menu.
Start
This function is used to set the hours and minutes for storage temperature to become active.
Press select button 1 and the current four-digit hour and minute setting will be displayed (24 hour)
Press & hold select button 1: Set Hours
Press & hold select button 2: Set Minutes
Press select buttons 1 & 2 simultaneously to move to the next item on the menu.
Stop
This function is used to set the hours and minutes for storage temperature to become inactive.
Press select button 1 and the current 4-digit hour and minute setting will be displayed (24hour).
Press & hold select button 1: Set Hours
Press & hold select button 2: Set Minutes
Press select buttons 1 & 2 simultaneously to move to the next item on the menu.
Storage Temperature
(Default Temperature 600F/ 160C)
This function is used to set the temperature for product storage. Press select button 1 and “tt.tx”
will show on the display where x is Fahrenheit or Celsius and tt.t is the degrees.
Press and hold select button 1 to increase or decrease the number by 1 or 0.5. Release select
button with the display showing the temperature you wish to use and display will return to
“Storage Temperature”
Press select buttons 1 and 2 simultaneously to scroll to “Storage Enabled”
Storage Enabled
This function is used to enable the storage setting to go in affect.
Press select button 1 and the current setting will be displayed (On or Off).
Press and hold select button to toggle between ”On or Off”.
Release the select button showing the setting you wish to use and display will return to “Storage
Enabled”
Press select buttons 1 & 2 to scroll to “Return”
Return
Press select button 1 at “Return” to return to “Refrigeration”
Press select buttons 1 & 2 simultaneously to scroll to next item on the menu.

PROGRAMMING P-SERIES
Page 19 of 76
Free Vend
This function is used to set the Free Vend option. Note: For free vend to become active a free vend
switch must be connected to controller on free vend switch connector. Press select button 1 and
“ENABLE” will show on the display. To move to Override, press & hold select buttons 1 & 2
simultaneously.
Enable
This function is used to allow the free vend to go in affect.
Press select button 1 and the current setting will be displayed (On or Off).
Press and hold select button 1 to toggle between “ On ” or “Off ”.
Release the select button showing the setting you wish to use and the display will return to
“Enable”.
Press select buttons 1 & 2 to scroll to “Display”
Display
This function is used to show the current number of free vends performed by the controller.
Press select button 1 and “#” will show on the display where “#” is the number of free vends
performed by the controller. Release the select button and display will return to “Display”
Press select buttons 1 and 2 simultaneously to scroll to “Reset”
Reset
This function is used to reset number of free vends to zero.
Press and hold select button 1 for 5 seconds to reset the number of free vends performed by the
controller to zero. Release the select button and the display will return to “Reset”.
Press select buttons 1 & 2 to scroll to “Return”.
Return
Press select button 1 to return to “Free Vend”.
Press & hold select buttons 1 & 2 simultaneously to move to the next item on the menu.
Override
This function is used to allow a key switch to override some of the settings stored for normal operations.
When enabled and the free vend switch is in the closed position, the controller will override “Free Vend”,
disable vending, disable currency acceptance, display will show “No Sales”, and lights will be off. The
compressor will continue to keep product at the programmed temperature. Vender will remain in this state
until the override switch is in the open position.
Press select button 1 and the display will show the current setting for 2 seconds (ON or Off).
Press and hold select button 1 to toggle between “On” -enabled and “Off” -disabled.
Release the select button showing the setting you wish to use and display will return to “Override”.
To move to Sales Message, press & hold select buttons 1 & 2 simultaneously.
Sales Message
This function is used to turn on the scrolling message “Ice Cold Drink”.
Press select button 1 and the display will show the current setting (On or Off).
Press and hold select button 1 to toggle between “ On or Off”.
Release the select button showing the setting you wish to use and display will return to “Sales Message”.
Press select buttons 1 & 2 simultaneously to scroll to “Recharge”
Recharge -The installed Card Reader must support this option for this feature to
work correctly.
This function is used to enable the recharge card setting routine.
Press select button 1 and the display will show the current setting (On-recharge card enabled or Off-
recharge card disabled). Press and hold select button 1 to toggle between “On” and “Off ”.
Release the select button showing the setting you wish to use and display will return to “Recharge”.
Press select buttons 1 & 2 simultaneously to scroll “Return”

PROGRAMMING P-SERIES
Page 20 of 76
Return
Press select button 1 to return to “User Menu”.
Press & hold select buttons 1 & 2 simultaneously to move to the next item on the menu.
Diagnostics
This function allows you to systematically diagnose problems related to the vender. To move to “Auto Test” press
select buttons 1 & 2 simultaneously, to enter sub-menu press select button 1. The following are sub-menus of
Diagnostics Menu:
Vender with DC motors “Selection”, “Home Sensor”, “Vend Sensors”, “Motors”, “Coin mech”, “Note
Acceptor”, “Display”, “Relay”, “Jog”, “Prime”, and “Return”.
Selection
Press any select button, and the display will indicate the number of the select button pressed.
Press & hold select buttons 1 & 2 simultaneously to the next item on the menu.
Home Sensor -This prompt only appears on machines with DC motors.
Use this to test the home sensor on the motor for any column. Press select button 1 to display “Column
1”. Press & hold select buttons 1 & 2 simultaneously to scroll through the columns and “Return”. Press
button 1 when a column is displayed will cause the displayed column to test that the motor’s home sensor
can be detected. Press select button 1 at “Return” to return to “Home Sensor”.
Press & hold select buttons 1 & 2 simultaneously to move to the next item on the menu.
Vend Sensors -This prompt only appears on machines with DC motors.
Use this to test vend sensor in the machine. Press select button 1 to begin the test and “TEST CHUTE”
will be displayed. Touch or place an object on the chute. When it is detected “Chute Pass” will be
displayed. If nothing is detected on the chute, a “CHUT” message will be displayed.
Press & hold select buttons 1 & 2 simultaneously to move to the next item on the menu.
Motors
Use this test to run any motor in the stack. Press select button 1 and “Motor 1” will show on the display.
Use the following select buttons to run this test.
Press Select Buttons 1 & 2: Press until desired motor # to run or “Return” is shown on the display.
Press Select Button 1: Press to run the selected motor. The display will show “Vending” and the
selected motor will run.
Coin Mech
Use this test to check coin mech, coin chute, and the coin mech payout systems. Inserting any coins
enters the coin mech diagnostic function. Only tubed coins (i.e. that can be returned) will be accepted.
The value of the coins will be reflected on the display. Press select button 2 will exit the test and return
any coins inserted and return to “Coin mech”.
Press select buttons 1 & 2 simultaneously to move to the next item on the menu.
Note Acceptor
Use this test to check note acceptor. Inserting a bill enters the note accepter diagnostic function. Bill will
be held in escrow. Press select button 2 to stack the bill. Press select button 3 to return the bill. After the
note is has been stacked or returned, the display will return to “Note Acceptor”.
Press & hold select buttons simultaneously to move to the next item on the menu.
Display
Press select button 1 and the display segments will illuminate in a scrolling manner, or will scroll through
a set of text characters and return to “Display”.
Press & hold select buttons 1 & 2 simultaneously to move to the next item on the menu.