DMP Electronics 734INT Installation guide

INSTALLATION AND PROGRAMMING GUIDE
734INT Access
Control Module

About the 734INT....................................... 1
Power Supply......................................................... 1
Zone Terminals ...................................................... 1
Annunciators.......................................................... 1
Indicator LEDs ....................................................... 1
Form C Relay......................................................... 2
Programming Connection................................ 2
Keypad In and Out Connections ................... 2
PCB Features...............................................3
Install the 734INT .......................................4
Mount the 734INT ............................................... 4
Wire the Access Control Lock........................ 5
Isolation Relay (optional) ................................. 7
Install the 333Suppressor ............................... 8
Wire the Zone Terminals................................... 9
Connect a Wiegand Card Reader................. 11
Set the 734INT Address...................................14
TABLE OF CONTENTS
Program the Panel.................................... 17
Device Setup ........................................................ 17
Device Number .................................................................. 17
Device Name.......................................................................17
Device Type .........................................................................18
Communication Type.......................................................18
Program the 734INT................................. 19
Programmer Menu ............................................20
Initialization Options........................................20
Access Options ...................................................21
Activate Zone 2Bypass ..................................................21
Activate Zone 3 Request to Exit.................................23
Activate Onboard Speaker ...........................................24
Card Formats.....................................................................24
Require Site Code............................................................28
Number of User Code Digits .......................................29
Card Format Added/Changed (Custom Format)29
No Communication with Panel .................................. 30
Remove Keypad..................................................31

Keypad Bus Wiring Specifications.........32
Public Card Formats ................................33
International Certifications.................... 34
Intertek (ETL) Listed........................................34
Product Specifications ........................... 36
Readers and Credentials .........................37

Digital Monitoring Products, Inc. | 734INT Installation and Programming Guide 1
Annunciators
An onboard programmable piezo provides
local annunciation at the 734INT. You can
also connect a variety of switched ground
annunciators to the 734INT for remote
annunciation.
Indicator LEDs
The 734INT provides three indicator LEDs:
• RELAY (red) turns on for the same
duration as the door strike relay.
• WIEGAND (yellow) turns on for one
second to indicate receipt of valid input.
• DATA (green) indicates that the module
is communicating with the panel.
The 734INT Access Control Module allows you to use the powerful, built in access control
capability of DMP Panels using smartcard, proximity, mag stripe, or biometric readers, or
other compatible authentication devices. The 734INT includes the following features:
Power Supply
The 734INT operates at 12/24VDC from
the power supply supporting a door’s
magnetic lock or door‑strike.
Warning: To avoid the risk of
equipment damage, do not exceed
750mA total output current for
zones connected to the module.
Zone Terminals
Zones 1 ‑ 4on the 734INT can be
programmed for a variety of burglary or
access control applications.
ABOUT THE 734INT

2 734INT Installation and Programming Guide | Digital Monitoring Products, Inc.
Form C Relay
The 10Amp Form C relay draws up to
35mA of current. Refer to “Wire the
Access Control Lock” and “Isolation Relay
(optional)” in this document for more
information.
Programming Connection
The 734INT also provides a keypad
programming connection that allows
you to use a standard DMP LCD keypad
for initial setup. Programming can be
completed using a keypad connected to
the 734INT or from XR150INT/XR550INT
Series panels.
Keypad In and Out
Connections
The keypad in (KYPD IN) connection
receives and transmits data to the panel
Keypad Bus or AX‑Bus.
The keypad out (KYPD OUT) connection
receives and transmits data out to
other keypads or modules. Install a
dual connector four‑position harness
to allow daisy chain connection to
other devices, up to the maximum
number of devices supported. XR150INT
Series panels support up to 8devices.
XR550INTSeries panels support up to
16devices. When using the AX‑Buses with
XR550INT devices, you can have 32 doors,
expandable to 96.
Caution: When the 734INT is powered
from 24VDC, do not connect devices
to KYPD OUT header.

Digital Monitoring Products, Inc. | 734INT Installation and Programming Guide 3
PCB FEATURES
RED
PROG
RED
KYPD OUT
DATA
XMT LED
WIEGAND
READ LED
RELAY
ON
NC
C
NO
GRN
YEL
RED + –
Piezo
1234 5 6 7 810 11 12 13 14
9
LC ASREDWHTGRN BLK Z1 Z2 Z3 Z4+ Z4–RA GND GND
KYPD IN
RED
ON
1 2 3 4
Door Relay
Terminal
Reader
Inputs
Status
Indicator
Outputs Zones
To Panel
Keypad Bus
or AX-Bus
To Other
Keypad Bus
or AX-Bus
Piezo
Indicator
LEDs
Keypad
Programming
Header
Address Dip
Switches
Figure 1: PCB Features

4 734INT Installation and Programming Guide | Digital Monitoring Products, Inc.
INSTALL THE 734INT
Mount the 734INT
The module comes in a high‑impact plastic housing that you can mount directly to a
wall, backboard, or other flat surface.
For easy installation, the back and ends of the 734INT housing have wire entrances.
The back also contains multiple mounting holes that allow you to mount the module
on a single‑gang switch box. DMP recommends mounting the 734INT near the
protected door. Refer to Figure 2 for mounting hole locations on the housing base.
1
1. Remove the PCB from the
plastic housing by loosening
the clips on one side and gently
lifting it out of the housing base.
2. Insert the included screws in the
desired mounting hole locations
and tighten them to secure the
housing to the surface.
3. Reinstall the PCB in the housing
base.
Mounting Holes
Figure 2: Mounting Hole Locations

Digital Monitoring Products, Inc. | 734INT Installation and Programming Guide 5
Wire the Access Control Lock
The 734INT provides a Form C (SPDT) relay for controlling locks and other
electronically‑controlled barriers. The three relay terminals marked NO C NC allow
you to connect the device wiring to the relay for module control.
Use an additional power supply to power magnetic locks and door strikes. See
Figure 3and Figure 4for typical magnetic lock and door strike wiring.
The Form C relay draws up to 35mA of current and contacts are rated for 10Amps
(resistive) at 12/24VDC. When connecting multiple locks to the Form C relay, the
total current for all locks cannot exceed 10Amps. If the total current for all locks
exceeds 10Amps, problems may arise and an isolation relay may be needed. Refer
to “Isolation Relay (optional)” for more information.
2
Model 333
Suppressor
–+
12/24 VDC
Power Supply
Normally Closed
Magnetic Door
Lock
Mag lock positive
to Terminal NC
Power supply positive
to Terminal C
Mag lock negative to
power supply negative
Figure 3: Typical Magnetic Lock Wiring
Model 333
Suppressor
–+
12/24 VDC
Power Supply
Normally Open
Door strike positive
to Terminal NO
Power supply positive
to Terminal C
Door strike negative to
power supply negative
DC Door Strike
Figure 4: Typical Door Strike Wiring

6 734INT Installation and Programming Guide | Digital Monitoring Products, Inc.
KYPD IN / KYPD OUT Connections
• KYPD IN (Keypad In): Receives and transmits data to the panel Keypad bus/AX‑
Bus.
• KYPD OUT (Keypad Out): Receives and transmits data out to other keypad(s) or
module(s). Install a dual‑connector harness to allow connection to other devices
up to the maximum number of devices supported.
When the 734INT is powered from 24VDC, do not connect devices to KYPD OUT header.
Status LEDs
The 734INT board contains three status LEDs.
• The Red LED turns on for the same duration as the door strike relay.
• The Yellow LED turns on for one second to indicate receipt of a valid input
determined by card format programming.
• The Green LED indicates data sent to the panel.